Abstract:To produce castings of titanium, nickel, copper, aluminum, and zinc alloys, graphite molds can be used, which makes it possible to provide a high cooling rate. No die coating and lubricant are required in this case. Computer simulation of casting into graphite molds requires knowledge of the thermal properties of the poured alloy and graphite. In addition, in order to attain adequate simulation results, a series of boundary conditions such as heat transfer coefficients should be determined. The most important ones are the interface heat transfer coefficient between the casting and the mold, the heat transfer coefficient between the mold parts, and the interface heat transfer coefficient into the environment. In this study, the interface heat transfer coefficient h between the cylindrical aluminum (99.99%) casting and the mold made of block graphite of the GMZ (low ash graphite) grade was determined. The mold was produced by milling using a CNC milling machine. The interface heat transfer coefficient was found by minimizing the error function reflecting the difference between the experimental and simulated temperatures in a mold and in a casting during pouring, solidification, and cooling of the casting. The dependences of the interface heat transfer coefficient between aluminum and graphite on the casting surface temperature and time passed from the beginning of pouring are obtained. It is established that, at temperatures of the metal surface contacting with a mold of 1000, 660, 619, and 190°C, the h is 1100, 4700, 700, and 100 W/(m2 K), respectively; i.e., when cooling the melt from 1000°C (pouring temperature) to 660°C (aluminum melting point), the h rises from 1100 to 4700 W/(m2 K), and after forming the metal solid skin on the mold surface and decreasing its temperature, the h decreases. In our opinion, a decrease in the interface heat transfer coefficient at casting surface temperatures lower than 660°C is associated with the air gap formation between the surfaces of the mold and the casting because of the linear shrinkage of the latter. The heat transfer coefficient between mold parts (graphite–graphite) is constant, being 1000 W/(m2 K). The heat transfer coefficient of graphite into air is 12 W/(m2 K) at a mold surface temperature up to 600°C.

Equivalent Heat Transfer Coefficient at Casting/Cu Mould Interface and Temperature Field Simulation

A Study of the Interfacial Heat Transfer Between an Iron Casting and A Metallic Mould

Study on Heat Transfer Behavior at Metal/Die Interface in Aluminum Alloy Die Casting Process - I. Experimental Study and Determination of the Interfacial Heat Transfer Coefficient

Measurement of Temperature Inside Die and Estimation of Interfacial Heat Transfer Coefficient in Squeeze Casting

Determination of interface heat transfer coefficient between aluminum casting and graphite mold

Investigation and Application of Inverse Determination of Interfacial Heat Transfer Coefficient in Vacuum Investment Casting

Numerical Simulation of Temperature Field and Grain Structure in Cu-10Al Alloy Produced by Heated Mould Continuous Casting

Determination of the Interfacial Heat Transfer Coefficient at the Metal-Sand Mold Interface in Low Pressure Sand Casting

STUDY OF INTERFACIAL HEAT TRANSFER COEFFI-CIENT BETWEEN METAL AND DIE DURING HIGH PRESSURE DIE CASTING PROCESS OF ALUMINUM ALLOY ADCl2Z

Determination of Interfacial Heat Transfer Coefficient at the Frozen Sand Mold Casting Process of ZL101 Alloy

Spatial interfacial heat transfer and surface characteristics during gravity casting of A356 alloy

Experimental Study on the Heat Transfer Behavior and Contact Pressure at the Casting-Mold Interface in Squeeze Casting of Aluminum Alloy

An Inverse Estimation of Frozen Sand Mold-Melt Heat Transfer Coefficient in the Solidification of A356 Alloy

Study on the Heat Transfer at the Casting-Mould Interface in Resin-Bonded Sand Mould Casting of Mg-Gd-Y-Zr Alloy

Heat transfer coefficient during cooling water of continuous casting of aluminum alloy

Method for Determining the Boundary Condition of Heat Transfer in Mold for Slab Casting

Numerical simulation and experimental verification of the initial temperature distribution of castings during mold filling process

Development of Thermal Boundary Condition Model at Metal/die Interface of High Pressure Die Casting Process

Numerical Simulation of Fluid Flow and Solidification in Continuous Slab Casting Mould Based on Inverse Heat Transfer Calculation

Heat Transfer Coefficient Determination in a Gravity Die Casting Process with Local Air Gap Formation and Contact Pressure Using Experimental Evaluation and Numerical Simulation

Investigating the suitability of using a single heat transfer coefficient in metal casting simulation: An inverse approach