Abstract:Cu2O/CuO bilayers were fabricated by electrodeposition of the CuO layer in a copper(II)-ammonia complex aqueous solution, followed by photoelectrochemical deposition of the Cu2O layer at potentials ranging from -0.3 to -1.0 V referenced to a Ag/AgCl electrode in a copper(II)-lactate complex aqueous solution under light irradiation, and the effects of varied potentials of the photoelectrochemical Cu2O depositions and post-heating conditions on their structural, optical, and photovoltaic characteristics were investigated with X-ray diffraction, field emission-scanning electron microscopy, optical absorption measurements, and external quantum efficiency (EQE) measurements with and without applied bias voltage. The Cu2O layers with a characteristic 2.1 eV band gap energy were adhesively stacked on the thorn-like grains of the CuO layers possessing a characteristic 1.5 eV band gap energy, and dense and defect-free Cu2O/CuO bilayers could be fabricated at the potentials of -0.4 and -0.5 V, but the grain size of Cu2O decreased at -0.5 V. In addition, the metallic Cu was deposited simultaneously at potentials less than -0.7 V. The Cu2O/CuO bilayer fabricated at -0.4 V revealed photovoltaic features at wavelengths ranging from 350 nm to approximately 900 nm, and a maximum EQE value of 56.8% was achieved at 510 nm in wavelength with a bias voltage of -0.1 V. The maximum EQE value, however, decreased to 1.2% accompanied with the peak wavelength shift to 580 nm, and no photovoltaic feature was observed at potentials of -0.3, -0.7, and -1.0 V. The photovoltaic performance for the Cu2O/CuO bilayer fabricated at -0.4 V was ameliorated by heating at 423 K, and the maximum EQE values were enhanced to 87.7% at 550 nm and 89.8% at 530 nm in an ambient atmosphere and vacuum. Both the Cu2O and CuO layers acted as photovoltaic layers in the Cu2O/CuO bilayer fabricated at -0.4 V and heated at 423 K, and the electrical characteristic including the carrier mobility affected the photovoltaic performance. The photovoltaic feature, however, disappeared by heating above 523 K due to the formation of nanopores inside the CuO layer and near the CuO heterointerface to the Cu2O and fluorine-doped tin oxide substrate.

Introducing a Protective Interlayer of TiO2 in Cu2O–CuO Heterojunction Thin Film As a Highly Stable Visible Light Photocathode

CuBi2O4/CuO Heterojunction Coated with Electrodeposited ZnO Overlayer for Stable Solar Hydrogen Evolution

Improvement of the Photoelectrochemical Stability of Cu2O Photocathode by PhCCCu Grafting

Cu2O/CuO heterojunction formed by thermal oxidation and decorated with Pt co-catalyst as an efficient photocathode for photoelectrochemical water splitting

Optimization of PEC and photocathodic protection performance of TiO2/CuInS2 heterojunction photoanodes

Semitransparent Cu2O films based on CuO Back Layer for Photoelelctrochemical Water Splitting and Photovoltaic Applications

Embedment of Anodized P-Type Cu2O Thin Films with CuO Nanowires for Improvement in Photoelectrochemical Stability

Facile Construction TiO2/ZnIn2S4/Zn0.4Ca0.6In2S4 Ternary Hetero-Structure Photo-Anode with Enhanced Photo-Electrochemical Water-Splitting Performance

Cu 2 O/CuO composite for efficient performance in photoelectrochemical and optoelectronics applications

In situ loading of ultra-small Cu 2O particles on TiO 2 nanosheets to enhance the visible-light photoactivity

Enhanced photoelectrochemical water splitting via hydrogenated TiO 2 nanotubes modified with Cu/CuO species

Titanium Nitride Protected Cuprous Oxide Photocathode for Stable and Efficient Water Reduction

Enhancing Charge Transport in CuBi2O4 Films: The Role of a Protective TiO2 ALD Coating Probed by Impedance Spectroscopy

Photoelctrochemically Fabricated and Heated Cu2O/CuO Bilayers with Enhanced Photovoltaic Characteristics

Core-shell structured Cu2O@HKUST-1 heterojunction photocatalyst with robust stability for highly efficient tetracycline hydrochloride degradation under visible light

Boosting the photocathode performances of protected Cu2O inverse opals using photonic-crystal heterostructures

A high-performance TiO2 protective layer derived from non-high vacuum technology for a Si-based photocathode to enhance photoelectrochemical water splitting

p-Type Cu<sub>2</sub>O as an effective interlayer between CdS and NiO<sub>x</sub> cocatalysts to promote photocatalytic hydrogen production

Hybrid Overlayer of Defective Ni-MOF and NiO Nanoparticles toward Efficient TiO2/CdS Type-II Heterojunction

CuO/CuBi2O4 bilayered heterojunction as an efficient photocathode for photoelectrochemical hydrogen evolution reaction

Si-doped Cu2O/SiOx composites for efficient photoelectrochemical water reduction