Abstract:As significant fluid machinery, canned motor pumps are widely applied in industrial field. The typical characteristic of canned motor pump is that the fluid comes into the narrow gap and affects the performance of canned motor. The coolant flow in the narrow annular gap between rotor and stator cans belongs to Taylor-Couette-Poiseuille flow which has been investigated for a long time while the thermal design is a key function of internal narrow gap annular flow of canned motor. However, the temperature distribution prediction of canned motor deviates from the experiments, especially in the high-capacity canned motor due to the large shear rate of fluid and eddy-current loss of motor's can. According to the researcher's work, the significant work lies in the heat transfer coefficient that different researchers give various numerical prediction and experimental measurement. It brings big challenge in thermal design of high capacity canned motor pump. In this paper, the author focuses on the reason why the heat transfer coefficient is remarkably lower than that other's forecast. In this paper, the heat transfer behavior of the boundary layer near surfaces in the annular flow is investigated by using the commercial fluid dynamic (CFD) method. Firstly, the Naiver-Stocks (N-S) equations and energy conservation equation are employed for modeling the flow and heat transfer behavior, and the k-omega turbulent model is used for solving the flow control equations. Secondly, the fluid domain is described by a simplified geometrical model: two concentric cylinders with finite gap length. Thirdly, numerical approach is used to analyze the subject with tools of Solidworks, ICEM CFD and Ansys Fluent. Two parameters are analyzed in the research, namely the rotating speed and the wall heat flux, without considering the fluid viscous dissipation and thermal contact resistance. Numerical simulation results indicate that Taylor vortex exists in the flow regime, and the temperature distribution is affected by both the rotating speed and the wall heat flux, named thermal barrier effect under large heat flux condition. The thermal barrier effect lies in that the temperature gradient of interface decreases compared to the peak value of temperature gradient near the surface, so that the heat transfer coefficient is reduced remarkably. This effect leads to the temperature prediction deviates from the experiment measurement.

An Effective Viscosity Equation For The Cfd Analysis Of The Micro Flows In The Confinement Ring

Finite Volume Method of the Microfiltration of Viscoelastic Polymer Solution

Simulation of Couette Flow Using Conventional Burnett Equations with Modified Slip Boundary Conditions

Close-contact Melting of Shear-Thinning Fluids

Numerical Analysis of the Micro-Couette Flow Using a Non-Newton–fourier Model with Enhanced Wall Boundary Conditions

Analytical Method of Nonlinear Coupled Constitutive Relations for Rarefied Non-Equilibrium Flows

- 1-development and validation of high-precision cfd method with volume-tracking algorithm for gas-liquid two-phase flow simulation on unstructured mesh i 1

Simulation of Flow and Heat Transfer in Micro Couette Flow

CFD Study of Flow Fields in an Oscillatory Flow Reactor with Conic Ring Baffles

Numerical Investigations of Liquid Film Offtake by Transverse Gas Flow in a Downcomer Annulus Geometry

Flow Behavior Analysis in Tight Lattice Rod Bundle Using CFD Method

Numerical Prediction of CHF Based on CFD Methodology under Atmospheric Pressure and Low Flow Rate

A Fast Convergent Semi-analytic Method for an Electrohydrodynamic Flow in a Circular Cylindrical Conduit

CFD Simulations of the Air/Water Two-phase Flow in an Annular Centrifugal Contactor

Chemically reactive magnetized flow of viscoplastic nanofluid through a vertical cone considering non-Darcy porous media

Numerical simulation of single-phase flow in a single square tube with blockage

Heat Transfer Behavior Of The Boundary Layer Near Surfaces In Annular Flow Of High Capacity Canned Motor Pump

Mixed Lubrication Problems in the Presence of Textures: an Efficient Solution to the Cavitation Problem with Consideration of Roughness Effects

Cfd Application To Subcooled Boiling Analyses On The First Wall Of Wccb Blanket For Cfetr

Design and Flow Simulation on a Variable Structure Plasma Reaction Chamber

CFD analysis for full vessel upper plenum in Maanshan Nuclear Power Plant