Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Dry Sliding Behaviors of Polydicyclopentadiene under Elevated Sliding Velocity

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Improved Interfacial Adhesion And Manufaturing Method Of Mgf/P-Dcpd Composites Using W, Mo, Or Ru Type Catalysts In Air Condition

Mechanical Properties of Polydicyclopentadiene/graphite Nanosheet Composites Prepared by Reaction Injection Moulding

The Tribological and Mechanical Properties of Pdcpd/Pew Composites Prepared by Reaction Injection Moulding

Tribological Behaviors of Several Polymer–polymer Sliding Combinations under Dry Friction and Oil-Lubricated Conditions

Sliding Friction Behaviors of Poly (p‐phenylene Benzobisoxazole) (PBO) Film under Different Conditions

Dry Friction Characteristics of Ti-6Al-4V Alloy under High Sliding Velocity

Effects of Fiber Diameter and Tribotest Conditions on Nonlubricated Frictional Behavior of a Microsized Metal Fiber

Research on stick–slip behavior and tribological properties of ethylene–propylene diene monomer under various wear velocity conditions

Comparative Study of Tribological Properties of Polyphenylene Sulfide (PPS), Polyethersulfone (PES), and Polysulfone (PSU)

Study on the Friction and Sliding Wear Behavior of Hybrid Polytetrafluoroethylene/Kevlar Fabric Composites Filled with Polyphenylene Sulfide

Friction and wear behaviors of polycrystalline diamond self-mated pairs in air and water lubrication conditions

Dry sliding tribological behavior of C/SiC under different load and speed

Determination of the Effect of Sliding Speed on Tribological Performances of Carbon Fiber Reinforced, Graphite and PTFE Filled Poly-ether-ether-ketone (PEEK) Polymer Composite

Significant sliding speed effect on the friction and wear behavior of UHMWPE matrix composites

Friction and Wear of Polyphenylene Sulfide (PPS), Polyethersulfone (PES) and Polysulfone (PSU) Under Different Cooling Conditions

Ultralow Friction and Wear of Polymer Composites under Extreme Unlubricated Sliding Conditions

Tribological properties of PTFE/PPS films deposited on the ultrasonic rolling textured substrates by electrohydrodynamic atomization under dry reciprocating sliding

Mechanical and Tribological Properties of PA/PPS Blends