Abstract:Membrane biofouling represents a major challenge ever-present in the practical application of polyamide (PA) thin-film composite (TFC) reverse osmosis (RO) membranes. This work focused on grafting polyacrylamide (PAAm) onto PA-TFC via an in-situ atomic transfer radical polymerization (ATRP) method to improve the biofouling resistance of PA-TFC. The ATRP initiators, isobutyryl bromide (iPB), were introduced into PA matrix using a bifunctional small molecule, 2-bromoisobutyryl bromide (BIBB), added in organic hexane solutions to participate in interfacial polymerization through the condensation reaction with m-phenylenediamine. The successful introduction of iPB was confirmed by membrane surface characterizations, and the iPB density in PA layer was tuned by varying the BIBB concentrations in hexane solutions based on the variation in water permeance and salt rejections of iPB-loaded PA-TFC. The ATRP for the gradual growth of PAAm brush was thus in-situ achieved on the PA-TFC surface from the pre-incorporated iPB groups and the length of PAAm chains was facilely controlled via tuning ATRP polymerization time. The PAAm grafted PA-TFC exhibited a minimum decrement of water permeance and essentially retained salt rejections relative to the un-grafted ones. More importantly, the grafted membranes presented synergistically enhanced anti-adhesion and bacteriostatic performance towards either Gram-negative Escherichia coli (E. coli) or Gram-positive Bacillus subtilis (B. subtilis). Also, the grafted membranes presented a lower final flux decline ratio (FDRf) and higher final flux recovery ratio (FRRf) in relation with the un-grafted membranes in the dynamic bovine serum albumin (BSA) fouling test. Particularly, the membrane grafted with longer PAAm chains from extended grafting time showed better anti-biofouling performance: the sterilization ratio towards E. coli and B. subtilis achieved up to 98.8% and 99.0%, respectively, and FDRf of just 3.7% and FRRf of 97.6% after 3 × 8 h BSA fouling test for the membrane subjected to 2 h ATRP grafting. The PAAm grafting induced greater water wettability of membrane surface and the flexible chain structure of PAAm were proposed to account for the enhanced anti-adhesion and bacteriostasis towards bacteria, which collaboratively led to the improved biofouling resistance.

Polypropylene Hollow Fiber Membranes With Grafted Poly(Acrylic Acid) Brushes From Surface-Initiated Atom Transfer Radical Polymerization And Their Ph-Dependent Antifouling Properties

Surface immobilization of polymer brushes onto porous poly(vinylidene fluoride) membrane by electron beam to improve the hydrophilicity and fouling resistance

Functional and Surface-Active Membranes from Poly(vinylidene Fluoride)-Graft-poly(acrylic Acid) Prepared Via RAFT-mediated Graft Copolymerization.

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Tethering Hydrophilic Polymer Brushes Onto PPESK Membranes Via Surface-Initiated Atom Transfer Radical Polymerization

Improvement of the Antifouling Characteristics for Polypropylene Microporous Membranes by the Sequential Photoinduced Graft Polymerization of Acrylic Acid

Enhancing Membrane Surface Antifouling by Implanting Amphiphilic Polymer Brushes Using a Swelling Induced Entrapment Technique.

Preparation of antifouling reverse osmosis membrane with polyacrylic acid brushes based on polydopamine coating assisted atom transfer radical polymerization

Fouling Control In A Submerged Membrane-Bioreactor By The Membrane Surface Modification

Antibacterial Effect of Surface-Functionalized Polypropylene Hollow Fiber Membrane from Surface-Initiated Atom Transfer Radical Polymerization

Enhanced Fouling-Resistance Performance of Polypropylene Hollow Fiber Membrane Fabricated by Ultrasonic-Assisted Graft Polymerization of Acrylic Acid

Antifouling Pvdf Ultrafiltration Membranes Incorporating Pvdf-G-Phema Additive Via Atom Transfer Radical Graft Polymerizations

Antifouling and Self-Cleaning Performances of the Porous Polypropylene Membrane Surface Grafted by P(NIPAAm-PEGMA)

Surface Modification Of Microporous Polypropylene Membranes By Plasma-Induced Graft Polymerization Of Alpha-Allyl Glucoside

Hydrophilic Modification of Microporous Polysulfone Membrane Via Surface-Initiated Atom Transfer Radical Polymerization and Hydrolysis of Poly(Glycidylmethacrylate)

Microporous polypropylene hollow fiber membrane Part I. Surface modification by the graft polymerization of acrylic acid

HYDROPHILIC MODIFICATION OF PPESK POROUS MEMBRANES VIA AQUEOUS SURFACE-INITIATED ATOM TRANSFER RADICAL POLYMERIZATION

Improving the biofouling resistance of polyamide thin-film composite membrane via grafting polyacrylamide brush on the surface by in-situ atomic transfer radical polymerization

Antifouling Poly(Vinylidene Fluoride) Hollow Fiber Membrane With Hydrophilic Surfaces By Ultrasonic Wave-Assisted Graft Polymerization

Poly(Vinylidene Fluoride) Membranes with Hyperbranched Antifouling and Antibacterial Polymer Brushes

Antifouling and Antibacterial Improvement of Surface-Functionalized Poly(vinylidene Fluoride) Membrane Prepared Via Dihydroxyphenylalanine-Initiated Atom Transfer Radical Graft Polymerizations