Abstract:Freestanding, strip-shaped magnetoelastic (ME) biosensors are a class of wireless, mass-based biosensors that are being developed for the real-time detection of pathogenic bacteria for food safety and bio-security. The mass sensitivity of these biosensors operating in longitudinal-vibration modes is known to be largely dependent on the position of masses attached to the sensor surfaces. Hence, considering this dependence is crucial to the detection of low-concentration target pathogens, including single pathogenic bacteria, because their local attachment may cause varying sensor responses. In a worst case scenario, the resultant sensor responses (i.e., mass-induced resonance frequency changes of the sensor) may be too small to be detected despite the attachment of the target pathogenic masses. To address the issue, phage-coated ME biosensors (magnetostrictive strips (4 mm × 0.8 mm × 30 μm) coated with a phage probe specifically binding streptavidin protein) with localized masses (streptavidin-coated polystyrene beads) were fabricated, and mass-position-dependence of the sensor’s sensitivity under the fundamental-mode vibration was experimentally measured. In addition, three-dimensional finite element (FE) modal analysis was performed using the CalculiX software to simulate the phenomena. The experimental and theoretical results show close agreement: (1) the mass sensitivity was low when the mass was positioned in the middle of the sensor’s longest dimension and (2) a much higher mass sensitivity was, by contrast, obtained for the equivalent masses placed at both ends of the strip-shaped sensor. Furthermore, FE models were constructed for differently sized, phage-coated ME biosensors (100 – 500 μm in length with different widths and thicknesses) loaded with a single bacterial mass (2 μm × 0.4 μm × 0.4 μm, 1.05 g/cm 3 ) at varying longitudinal positions. The mass sensitivity was found to be approximated by a mass-position-dependent Boltzmann function whose amplitude is inversely proportional to the length squared, width, and thickness of the sensor.

Effects of Surface Phage Coverage on the Performance of Wireless Phage-Immobilized Magnetoelastic Biosensors

Effects of surface functionalization on the surface phage coverage and the subsequent performance of phage-immobilized magnetoelastic biosensors

Application of Biosensor Surface Immobilization Methods for Aptamer

Improved Surface Modification Approach for Micromechanical Biosensors

Blocking Agent Optimization for Nonspecific Binding on Phage Based Magnetoelastic Biosensors

Prediction of the Mass Sensitivity of Phage-Coated Magnetoelastic Biosensors for the Detection of Single Pathogenic Bacteria

High Throughput Pathogen Screening For Food Safety Using Magnetoelastic Biosensors

Novel “nano-phage” interfaces for wireless biosensors

Model Interface for Pathogens Detection Systems

Multiple Phage-Based Magnetoelastic Biosensors System for the Detection of Salmonella Typhimurium and Bacillus Anthracis Spores

Amorphous Magnetoelastic Sensors for the Detection of Biological Agents

Phage M13KO7 detection with biosensor based on imaging ellipsometry and AFM microscopic confirmation

Immobilization of Escherichia Coli for Detection of Phage T4 Using Surface Plasmon Resonance

Surface Functionalization, Bioanalysis, and Applications: Progress of New Magnetoelastic Biosensors

Multiple Phage-based Magnetoelastic Biosensors for the Direct Detection of Salmonella on Cantaloupes

Strategies for the Immobilization of Bacteriophages Applied in the Biosensors

Micro-Fabricated Wireless Biosensors For The Detection Of S. Typhimurium In Liquids

Detection of Bacillus Anthracis Spores Using Phage-Immobilized Magnetostrictive Milli/Micro Cantilevers

Novel Magnetostrictive Microcantilever and Magnetostrictive Nanobars for High Performance Biological Detection

Directional Immobilisation of SpyTag Bacteriophage on PDMS surfaces for Phage based Microfluidics

Detection of Salmonella Typhimurium Grown Directly on Tomato Surface Using Phage-Based Magnetoelastic Biosensors