New Insights into the Structure of a CeO2–ZrO2–Al2O3 Composite and Its Influence on the Performance of the Supported Pd-only Three-Way Catalyst

Li Lan,Shanhu Chen,Yi Cao,Maochu Gong,Yaoqiang Chen

DOI: https://doi.org/10.1039/c5cy00612k

IF: 6.177

2015-01-01

Catalysis Science & Technology

Abstract:CZA900 displays the most homogeneous structure, and consequently superior redox and catalytic performances are obtained for Pd/CZA900.

What problem does this paper attempt to address?

Effect of Ce/Zr Atomic Ratio on the TWC Properties of PdO/CexZr1-xO2(x=0-1.0) Catalysts

Ma Lei,Lu Chunshan,Zhang Qunfeng,Li Xiaonian

2010-01-01

Rare Metal Materials and Engineering

Abstract:The CexZr1-xO2 (x=0-1) composite oxides were prepared by sol-gel method, and then they were used as supportpr tp prepare PdO/CexZr1-xO2 catalysts. The effect of Ce/Zr atomic ratio on the structure of crystalline phase, redox property and TWC catalytic activity of CexZr1-xO2 composite oxides and PdO/CexZr1-xO2 catalysts were studied. The results show that phase structure of CexZr1-xO2 composite oxide depends on the CeO2 content. The different Ce/Zr atomic ratio affects the catalytic activity of PdO/CexZr1-xO2 catalysts much. In the reaction of NO-CO and CO-O-2, the catalytic activity of PdO/Ce0.8Zr0.2O2 catalyst is the highest. However, the catalytic activity of PdO/Ce0.5Zr0.5O2 catalyst is the highest in the reaction of CH4-O-2. The alpha: H-2-TPR peak is related probably to the NO-CO and CO-O-2 catalytic activity of PdO/Ce0.8Zr0.2O2 catalysts.
CO and Methane Oxidation Over CeXZr1-XO2 Mixed Oxide Supported PdO Catalysts

Lei Ma,Meng-Fei Luo,Li-Feng Han,Song-Ying Chen

DOI: https://doi.org/10.1023/A:1010313605332

2000-01-01

Reaction Kinetics and Catalysis Letters

Abstract:In this paper, the Ce X Zr 1-X O 2 -supported PdO catalysts were prepared and the effect of Ce/Zr ratio on catalytic activity for CO and methane oxidation was studied, both activity and the reduction behavior of catalyst depend on the Ce/Zr ratio. The reduction behavior of those catalysts was characterized by means of TPR.
Preparation of ceria-zirconia by modified coprecipitation method and its supported Pd-only three-way catalyst

Li Lan,Shanhu Chen,Yi Cao,Ming Zhao,Maochu Gong,Yaoqiang Chen

DOI: https://doi.org/10.1016/j.jcis.2015.03.042

2015-07-15

Abstract:A CeO2-ZrO2 compound with mixed phase composition (CZ4) was prepared by modified co-precipitation method, and for comparison, single-phase Ce(0.2)Zr(0.8)O2, Ce(0.5)Zr(0.5)O2 and Ce(0.8)Zr(0.2)O2 were synthesized via simultaneous co-precipitation method. The textural, structural and redox properties, together with the catalytic performance of the supported Pd-only three-way catalysts were investigated systematically. The results revealed that the generation of numerous interface sites in Pd/CZ4 due to its mixed phase composition (as confirmed by TEM observation) had a positive influence on modifying its structural, redox properties and thermal stability. The XRD and Raman results revealed that the highest structural stability was obtained by Pd/CZ4 with negligible lattice variation and slightest grain growth after aging treatment. The XPS analysis demonstrated that the compositional heterogeneity of Pd/CZ4 could facilitate the formation of Ce(3+), and was beneficial to preserve high dispersion of Pd as well as maintain Pd at a more oxidized state. The H2-TPR and oxygen storage capacity measurements indicated that Pd/CZ4 possessed highest reduction ability as well as largest oxygen storage capacity regardless of thermal aging treatment. And consequently Pd/CZ4 exhibited improved three-way catalytic activity compared with the catalysts supported on single-phase Ce(x)Zr(1-x)O2 both before and after thermal aging treatment.
Synthesis of a homogeneous CeO2–ZrO2-Al2O3 composite material by a novel hydrothermal assisted precipitation method

Shanshan Li,Zheng Zhou,Wenliang Xiong,Wei Wang,Linmei Wang,Zixuan Zheng,Jianli Wang,Yaoqiang Chen

DOI: https://doi.org/10.1016/j.mcat.2023.113660

IF: 4.6

2023-12-01

Molecular Catalysis

Abstract:CeO2-ZrO2-Al2O3(CZA) composites, combining the advantages of CeO2-ZrO2 (CZ) and Al2O3, are widely used in three-way catalyst as an indispensable support material. However, due to the adverse Zr-Al interaction and the different precipitation conditions for Ce3+/Ce4+ and Zr4+, the CZA prepared by conventional co-precipitation method has poor compositional homogeneity, resulting in degradation of redox properties. In this study, a homogeneous CZA composite is synthesized by a novel hydrothermal assisted precipitation method, in which the CZ-precipitates and Al-precipitates will be controlled separately. A quantitative EDX points analysis reveals that the Ce/Zr ratio in the resulting CZA material exhibits slight fluctuations between 0.72 and 0.91, which is much narrow than that from conventional precipitation method (0.38∼0.83). As a result, the resulting CZA material exhibits the better redox property, higher specific surface area, and more importantly, its supported Pd/CZA catalyst exhibit superior three-way catalytic activity, the T50 (temperature for 50% conversion) for CO, NO, C3H6 and C3H8 over which is 41 ℃, 26 ℃, 28 ℃ and 12 ℃, respectively, lower than that from conventional method.

chemistry, physical
Redox properties and metal–support interaction of Pd/Ce0.67Zr0.33O2–Al2O3 catalyst for CO, HC and NOx elimination

Siyu Lin,Linyan Yang,Xue Yang,Renxian Zhou

DOI: https://doi.org/10.1016/j.apsusc.2014.03.153

IF: 6.7

2014-01-01

Applied Surface Science

Abstract:Ce0.67Zr0.33 02, Ce0.67Zr0.3302-Al203 and -y-Al203 supported Pd catalysts (designated as Pd/CZ, Pd/CZA and Pd/Al2 03) have been characterized by XRD, CO chemisorption, in situ DRIFTS, XPS, HRTEM, H2-TPR, 02-TPSR and catalytic performance test. The results show that the small Pd0, particles dispersed in CZ would promote the conversion of HC, CO and NO2, while the Pd0, particles dispersed in Al203 promote the conversion of NO in the light-off process. Pd0, species mainly disperse on Al203-rich grains surface for fresh Pd/CZA catalyst, but easily migrate onto CZ-rich grains surface due to the strong interaction between Pd and ceria-based oxide under high temperature reaction conditions. And it promotes the thermal stability of Pd 0 species and resilience of Pd to Pd 0, therefore enhances the catalytic performance for HC, CO and NO elimination. Meanwhile, the interaction between CZ and Al203 can be enhanced after aging treatment, resulting in increasing the thermal stability of Pd/CZA catalyst. 2014 Elsevier B.V. All rights reserved.
Comparative study of three-way catalytic performance over Pd/CeO2-ZrO2-Al2O3 and Pd/La-Al2O3 catalysts: New insights into microstructure and thermal stability

Kai Chen,Jie Wan,Jiansong Lin,Renxian Zhou,Kai Chen,Jie Wan,Jiansong Lin,Renxian Zhou

DOI: https://doi.org/10.1016/j.mcat.2022.112361

IF: 4.6

2022-06-01

Molecular Catalysis

Abstract:Series of Pd/CeO2-ZrO2-Al2O3 (Pd/CZA) with different pore structures and lanthanum modified Pd/La-Al2O3 (Pd/La-A) were prepared via coprecipitation or hydrothermal method. The obtained catalysts were subjected to TWC activity evaluation, thermal stability tests as well as systematic characterizations including TEM, BET, Rietveld XRD, XPS, H2-TPR, O2-TPSR, and in situ DRIFTS. Results show that the TWC catalytic performance of Pd/Al2O3 catalyst can be obviously improved by CeO2-ZrO2 modification compared to La2O3 modification, due to the strong interaction between PdOx species and CeO2-ZrO2 support. The excellent thermal stability of Pd/CZA-2 catalyst is related to its different microstructure compared to Pd/CZA-1, because the abundant dissociated Zr4+ due to phase separation in Pd/CZA-2 could hinder the θ-Al2O3 to α-Al2O3 phase transition and retain small-sized PdOx species with excellent reoxidation ability. Besides, DRIFTS studies reveal clear structure-activity correlations between the adsorbed reaction intermediates and TWC catalytic performance, i.e. The formation of NO-Pd0 species on fresh Pd/CZA-1 is beneficial for NO conversion, while the rapid adsorption/decomposition of HC and carbonate species on Pd/CZA also contributes to better HC/CO oxidation. Nevertheless, the active sites poisoning by HC strong adsorption along with temperature-stable nitrate species on Pd/La-A cost its inferior catalytic behaviour regardless of thermal ageing.

chemistry, physical
Redox Behavior of Active PdOx Species on (ce,zr)xo2–al2o3 Mixed Oxides and Its Influence on the Three-Way Catalytic Performance

Siyu Lin,Linyan Yang,Xue Yang,Renxian Zhou

DOI: https://doi.org/10.1016/j.cej.2014.03.015

IF: 15.1

2014-01-01

Chemical Engineering Journal

Abstract:Two kinds of (Ce,Zr)(x)O-2-Al2O3 mixed oxides (designated as CZA-m and CZA-c) were prepared through mechanically mixed and co-precipitation method, and the corresponding supported Pd-only three-way catalysts calcined at different temperatures were investigated by XRD, N-2 adsorption, in situ DRIFTS, HRTEM, H-2-TPR and O-2-TPSR. The results show that PdOx species are mainly dispersed on Al2O3-rich grains surface in fresh catalyst, after thermal aging treatment, some PdOx species would migrate to (Ce,Zr)(x)O-2-rich grains surface due to the strong interaction of PdOx-(Ce,Zr)(x)O-2 and the sintering of alumina with loss of surface area. When thermally treated at 900-1000 degrees C, the interaction of both Al2O3-(Ce,Zr)(x)O-2 and PdOx-(Ce,Zr)(x)O-2-rich grains would be promoted, which enhances the thermal stability of PdO species and the reoxidation ability of Pd-0 to PdO under high temperature reaction conditions, especially for Pd/CZA-c catalyst. Meanwhile, more stable PdOx species which have strong interaction with support are formed and their reducibility is improved. Therefore, Pd/CZA-c catalyst exhibits better thermal stability than that of Pd/CZA-m. (C) 2014 Elsevier B.V. All rights reserved.
Synthesis of Stable CeO2-ZrO2/Al2O3 Material with Abundant Oxygen Vacancies for Pd-only Three-Way Catalyst Through Two Synergistic Lanthanum Doping Processes

Shanshan Li,Yi Zhao,Wei Wang,Ming Zhao,Jianli Wang,Yaoqiang Chen

DOI: https://doi.org/10.1016/j.seppur.2024.130677

IF: 8.6

2024-01-01

Separation and Purification Technology

Abstract:Stable support with abundant surface oxygen vacancies (Ov) is indispensable for robust sintering-resistant heterogeneous catalysts. Herein, a strategy of lanthanum (La) atom selectively doping has been put forward to construct the desirable CeO2-ZrO2/Al2O3 (CZA) support for high-temperature applications with the precise control of its distribution and location through two distinct addition processes. In the first addition process, La3+ was introduced to Al2O3 component by precipitation process to stabilize its structure by occupying the surface –OH sites and forming thermodynamically stabled LaAlO3. In the second addition process, the low-valence La3+ is surface grafted and preferentially captured by CZ component during preparation due to electrostatic attraction, thus generating abundant asymmetric Ov as anchor sites for metal nanoparticles. The resulting CZA supported Pd-based three-way catalyst exhibits superior intrinsic activity even being hydrothermally aged at 900 °C/10 h since the as-prepared CZA could anchor Pd species in smaller size and oxidized state due to the enhanced metal-support interactions. This work provides new insights into doping effects and offers an avenue to design stable and active support material for industrial applications.
Redox Properties And Metal-Support Interaction Of Pd/Ce0.67zro.3302-Al203 Catalyst For Co, Hc And No Elimination

Siyu Lin,Linyan Yang,Xue Yang,Renxian Zhou

DOI: https://doi.org/10.1016/j.apsusc.2014.03.153

IF: 6.7

2014-01-01

Applied Surface Science

Abstract:Ce0.67Zr0.33 02, Ce0.67Zr0.3302-Al203 and -y-Al203 supported Pd catalysts (designated as Pd/CZ, Pd/CZA and Pd/Al2 03) have been characterized by XRD, CO chemisorption, in situ DRIFTS, XPS, HRTEM, H2-TPR, 02-TPSR and catalytic performance test. The results show that the small Pd0, particles dispersed in CZ would promote the conversion of HC, CO and NO2, while the Pd0, particles dispersed in Al203 promote the conversion of NO in the light-off process. Pd0, species mainly disperse on Al203-rich grains surface for fresh Pd/CZA catalyst, but easily migrate onto CZ-rich grains surface due to the strong interaction between Pd and ceria-based oxide under high temperature reaction conditions. And it promotes the thermal stability of Pd 0 species and resilience of Pd to Pd 0, therefore enhances the catalytic performance for HC, CO and NO elimination. Meanwhile, the interaction between CZ and Al203 can be enhanced after aging treatment, resulting in increasing the thermal stability of Pd/CZA catalyst. 2014 Elsevier B.V. All rights reserved.
Morphology Controllable Synthesis of Pd/CeO2–ZrO2 Catalysts and Its Structure-Activity Relationship in Three-Way Catalytic Performance

Jie Wan,Xue Yang,Ting Wang,Yanjun Liu,Yuanyuan Zhou,Gongde Wu,Renxian Zhou

DOI: https://doi.org/10.1016/j.pnsc.2021.08.002

IF: 4.269

2021-01-01

Progress in Natural Science Materials International

Abstract:CeO2–ZrO2 mixed oxides with controlled morphologies (i.e., nanorod, nano-polyhedral and disordered shape) were synthesized through either hydrothermal or coprecipitation method, and the corresponding supported Pd/CeO2–ZrO2 catalysts were also prepared by conventional impregnation. The obtained catalysts were subjected to systematic structural/physio-chemical characterizations as well as three-way catalytic performance evaluations. The results showed that CeO2–ZrO2 mixed oxides presented different exposed crystal planes: namely disordered CZ-di mainly exposed (111) crystal planes, nanorod CZ-ro mainly exposed (111) crystal planes and few (100) crystal planes, while nano-polyhedral CZ-po exposed both (111) and (100) crystal planes. Clear structure-activity relationship could be demonstrated between the TWC (Three-way catalysts) performance of Pd/CeO2–ZrO2 and such different microstructures, as (100) and (111) crystal planes exposed by CZ-ro and CZ-po were beneficial for the surface oxygen vacancies formation, thus increasing the Pd-support interaction and effectively decreasing the light-off temperature of HC and NO elimination. On the other hand, the disordered CZ-di retained more lattice oxygen content, leading to better catalytic activity of CO elimination for the corresponding Pd/CZ-di catalyst.
Three-way catalytic performance of Pd/Ce0.67Zr0.33O2–Al2O3 catalysts: Role of the different Pd precursors

siyu lin,xue yang,linyan yang,renxian zhou

DOI: https://doi.org/10.1016/j.apsusc.2014.11.176

IF: 6.7

2015-01-01

Applied Surface Science

Abstract:•Pd dispersion and surface morphology are notable affected by Pd precursors.•PdOx species are mainly dispersed on Al2O3 surface in Pd/CZA(Cl) catalyst.•Pd/CZA(Cl) promotes HC and NO conversion, whereas Pd/CZA(NO) and Pd/CZA(NH) CO oxidation.•Surface chemistry under reaction conditions is revealed by in situ DRIFTS studies.
Construction of bimetallic Pt–Pd/CeO2–ZrO2–La2O3 catalysts with different Pt/Pd ratios and its structure–activity correlations for three-way catalytic performance

Kai Chen,Jie Wan,Ting Wang,Qi Sun,Renxian Zhou

DOI: https://doi.org/10.1016/j.jre.2022.10.014

IF: 4.632

2022-11-01

Journal of Rare Earths

Abstract:A series of Pt–Pd bimetallic catalysts supported on CeO2–ZrO2–La2O3 mixed oxides were synthesized through the conventional impregnation method. Three-way catalytic performance evaluations along with detailed physio-chemical characterizations were carried out to establish possible structure–activity correlations. Results show that on the one hand, different Pt/Pd ratios can strongly affect the TWC behaviors of Pt–Pd/CZL catalysts by modulating the synergistic effect between Pt and Pd. On the other hand, higher Pt/Pd ratio also favors better dispersion of precious metals. Such improved precious metals (PM) dispersion can promote the metal-support interaction and increase the surface oxygen vacancies concentration, thereby raising the dynamic oxygen storage/release capacity, improving the redox ability as well as enhancing the thermal stability of the Pt–Pd/CZL catalyst. Moreover, the strong metal-support interaction can augment surface oxygen vacancy concentration, thereby benefiting low temperature CO and NO reaction via augmented NO x adsorption and nitrate conversion.

chemistry, applied
Preparation of Cex Zr1-x-AI mixed oxides and investigation of the palladium-only three-way catalytic performance

Chun-qing YANG,Ren-xian ZHOU,Zhen-guo LI

DOI: https://doi.org/10.3785/j.issn.1008-9497.2008.04.016

2008-01-01

Abstract:The CexZr1-x-Al mixed oxides were prepared by the sol-gel method and the super-critical dryness method.The samples were characterized by means of XRD and BET techniques,and the three-way catalytic performance of their supported-Pd catalysts was also investigated.It was found that the samples calcined at 1 100 ℃ for 4 h still had large specific surface area(>95 m2·g-1) and no α-Al2O3 was formed.Based on the TEM and the investigation of catalytic performance,the catalysts containing cerium-zirconium solid solution had good catalytic activity and thermal stability,and the three-way catalytic performance of Pd/Ce0.75Zr0.25-Al was best.The catalyst Pd/Ce0.75Zr0.25-Al had low light-up temperatures(T20%) of 140 ℃,268 ℃,340 ℃ and 175 ℃ for CO,C3H6,NO and NO2,respectively,and the temperatures at which the reactants were converted fully were only raised by 10-20 ℃ after thermal aging.
Influence of Ceria-Zirconia Solid Solution on Performance of Noble Metal Monolithic Oxidation Catalyst

FU Huijing,FU Lixin,LI Junhua

DOI: https://doi.org/10.3969/j.issn.1004-0676.2006.02.008

2006-01-01

Abstract:CeXZr1-XO2 solid solution was prepared by co-precipitation method,while powder and monolith honeycomb catalysts were prepared by impregnating carriers with certain CeXZr1-XO2 aqueous solution.The crystalline structures of CeXZr1-XO2 and Ce0.5Zr0.5O2/Al2O3 were characterized by XRD,and the adsorbability was examined by TPD-C3H6.The results showed that the solid solution was obtained in CeO2-ZrO2 composite oxides,the addition of CeO2-ZrO2 to γ-Al2O3 improved the adsorptive power of CeXZr1-XO2/Al2O3 to C3H6.The behavior of these catalysts was examined by propene oxidation in a fixed-bed microreactor under excess oxygen.It was found that when the adding amount of CeXZr1-XO2 was equal,Pt/Ce0.6Zr0.4O2/Al2O3/cordierite showed the best activity,which was still lower than that of Pt/Al2O3/cordierite.So the addition of ceria-zirconia solid solution restrained the catalytic activity in the presence of excessive oxygen,when the amount of noble metal such as platinum was quite low.The more the ceria-zirconia solid solution was loaded,the worse was the performance of the catalysts as oxidative catalyst.
Preparation of Ce0.67Zr0.33O2 mixed oxides as supports of improved Pd-only three-way catalysts

Bo Zhao,Guangfeng Li,Changhua Ge,Qiuyan Wang,Renxian Zhou

DOI: https://doi.org/10.1016/j.apcatb.2010.02.031

2010-01-01

Abstract:Four types of Ce0.67Zr0.33O2 (CZCP, CZH, CZHP and CZM) mixed oxides as supports were prepared by coprecipitation, hydrothermal, homogeneous precipitation and microemulsion methods, respectively. The results show that both the preparation methods and the aging procedures have significant influences on the physicochemical properties of Ce0.67Zr0.33O2 mixed oxides. All these fresh Ce0.67Zr0.33O2 samples develop mesopore structure, especially that, CZCP obtains the largest diameter (20.87nm) and volume (0.455cm3/g). The XRD results indicate that fresh CZHP and CZCP samples contain cubic and tetragonal phases, while only cubic solid solution is found in fresh CZH and CZM samples, which show better low-temperature reducibility. Moreover, higher oxygen storage capacity complete (OSCC) values and faster O2 uptake are observed in CZH and CZM samples compared with those of fresh CZCP and CZHP. After calcination at 1100°C, it is found that the OSCC values and the kinetics of the O2 uptake for CZM and CZHP samples are deteriorated due to the coexistence of cubic and tetragonal phases as well as strong sintering of samples. On the contrary, the aged CZCP and CZH samples keep satisfactory low-temperature reducibility and oxygen storage capacity. For fresh catalysts, the pore-size distribution of mixed oxides seems to be important for catalytic activities. In contrast, for aged catalysts, their activities are related to both the redox properties and the textural properties of aged mixed oxides. Therefore, the Pd-only three-way catalyst supported on the CZCP exhibits the most promising amplified amplitude of stoichiometric window.
Effects of CeO2-ZrO2 Present in Pd/Al2O3 Catalysts on the Redox Behavior of PdOx and Their Combustion Activity

Renxian Zhou,Bo Zhao,Baohua Yue

DOI: https://doi.org/10.1016/j.apsusc.2008.01.075

IF: 6.7

2008-01-01

Applied Surface Science

Abstract:The ceria-zirconium-modified alumina-supported palladium catalysts are prepared using impregnation method with H2PdCl4 as Pd source, hydrazine hydrate as reducing agent. The physicochemical properties of these catalysts are characterized by BET surface area (BET), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction (H2-TPR) and temperature programmed oxidation (O2-TPO) techniques, and their catalytic activities for the combustion of methane are examined. The results show that the palladium mainly exist in a highly dispersed PdO species on Ce-Zr-rich grains as well as Al2O3-rich grains surfaces, and a stable PdO species due to the strong interaction between PdO and CeO2-ZrO2 on the Ce-Zr/Al2O3 surfaces. The catalytic activity is strongly related to the redox behavior of PdO species highly dispersed on Ce-Zr-rich grains and Al2O3-rich grains surfaces, and the higher the reducibility of the PdO species, the higher the catalytic activity. The presence of Ce-Zr in Pd/Al2O3 catalyst would inhibit the site growth of PdOx particles and decomposition of PdO to Pd0, and the reoxidation property of Pd0 to PdOx is significantly improved, which obviously increases thermal stability and catalytic activity of Pd/Ce-Zr/Al2O3 catalyst for the methane combustion.
Probing BaO Doping Effect on the Structure and Catalytic Performance of Pd/CexZr1–xO2 (x = 0.2–0.8) Catalysts for Automobile Emission Control

Linyan Yang,Xue Yang,Renxian Zhou

DOI: https://doi.org/10.1021/acs.jpcc.5b10301

2016-01-01

Abstract:Pd/CeO2-ZrO2-BaO (Pd/CZB) catalysts with 5.0 wt % BaO and different CeO2/ZrO2 molar ratio were synthesized. The modification with BaO significantly promotes the catalytic activity of HC and NO conversions when the molar ratio of CeO2 to ZrO2 is 2/1, because the substitution of Cex+/Zr4+ ions by Ba2+ promotes the formation of oxygen vacancy as revealed by XRD refinement analysis results and improves the mobility of active oxygen as a result of electronic and structural modifications. Among the Ba-doped catalysts, the crystalline form of the CZB supports gradually transform from cubic and pseudocubic to stable tetragonal phase as the increase of ZrO2 content. Meanwhile, the Raman results show that addition of moderate ZrO2 promotes the formation of structural defects, resulting in higher OSC and NOx storage efficiency. On the other hand, the introduction of moderate ZrO2 facilitates the dissociative adsorption of NO and promotes the deep oxidation of HC. Therefore, Pd/CZB catalysts with CeO2/ZrO2 molar ratio of 3/1-1/1, especially Pd/CZB21, show a much better catalytic activity of HC and NOx eliminations and a wider dynamic operation window. Zr-rich catalysts present worse catalytic activity of CO oxidation compared with Ce-rich catalysts, which is mainly arising from the decreased amount of active sites. After thermal aging treatment, Zr-rich catalysts (CeO2/ZrO2 < 1) undergo less severe deterioration of the catalytic activity compared with Ce-rich catalysts (CeO2/ZrO2 >= 1) as a result of better thermostability, and Pd/CZB11-a presents the best catalytic performance and widest dynamic operation window.
The Support Effect on Pdo/Ce0.7zr0.3ba0.1o2.1 and Cuo/Ce0.7zr0.3ba0.1o2.1 Catalysts

Min Chen,Lingyan Qi,Xiaoming Zheng

DOI: https://doi.org/10.1134/s002315840804006x

2008-01-01

Kinetics and Catalysis

Abstract:Ce0.7Zr0.3Ba0.1O2.1 mixed oxides (denoted as CZB) were prepared using macromolecule surface modified methods and used as supports to prepare low palladium content of PdO/CZB model catalysts. CuO/CZB series of catalysts were also prepared for comparison. The catalytic activity of the PdOCZB and CuO/CZB series of catalysts for low-temperature CO oxidation was investigated. A significant influence of the Ce0.7Zr0.3Ba0.1O2.1 support on the catalytic performance has been found. Using Ce0.7Zr0.3Ba0.1O2.1 as catalyst support increased the activity of CO oxidation and promoted the thermal stability significantly. It was found that the transition metal supported catalyst of 10.0 wt % CuO/CZB obtained a good result, as did the precious metal supported catalysts of 0.75 wt % PdO/CZB. The catalytic behaviors and thermal stability of PdO/CZB and CuO/CZB catalysts greatly depended on the support effect. The nature of Ce0.7Zr0.3Ba0.1O2.1 support was also characterized by surface area (BET method), x-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction with hydrogen (H-2-TPR) and X-ray photoelectron spectroscopy (XPS) technologies.
Cerium Based Shells with Palladium Cores Encapsulated: an Efficient Catalyst for Carbon Monoxide Oxidation

Wang Miao,Shen Meiqing,Wang Jianqiang,Wei Guangxi,Li Hang,Wang Jun

DOI: https://doi.org/10.1016/s1002-0721(14)60191-5

2014-01-01

Abstract:Pd@Zr/Ce O2 core-shell catalyst prepared by hydrothermal method was applied in CO oxidation reaction, exhibiting high CO oxidation activity at low temperature.XRD(X-ray diffraction) analysis demonstrated that the remarkable enhancement of catalytic performance was found to depend on the presence of more oxygen vacancies in the core-shell structure, which contributed higher content of and ready release of active oxygen species at low temperature, confirmed by H2-TPR(temperature programed reduction) results.Interestingly, introducing a small amount of zirconium(0.5 wt.%) exhibited a significant improvement of catalytic activity because the introduction of Zr further improved the amount of crystal defects and promoted the migration of oxygen species.
Highly efficient Pt catalyst on newly designed CeO2-ZrO2-Al2O3 support for catalytic removal of pollutants from vehicle exhaust

Wei Tan,Shaohua Xie,Xin Wang,Chunying Wang,Yaobin Li,Thomas E. Shaw,Lu Ma,Steven N. Ehrlich,Annai Liu,Jiawei Ji,Fei Gao,Lin Dong,Fudong Liu

DOI: https://doi.org/10.1016/j.cej.2021.131855

IF: 15.1

2021-12-01

Chemical Engineering Journal

Abstract:Pt-CeO2 catalysts have been widely studied for the vehicle emission control. Designing novel CeO2 based supports with improved physical-chemical properties has become a research hotspot to further promote the catalytic performance and stability of Pt-CeO2 catalysts. In this work, through utilizing a unique, two-step incipient wetness impregnation (T-IWI) method for ceria-zirconia-alumina (CZA-T) support preparation, a Pt single site catalyst (Pt/CZA-T) with excellent thermal stability was synthesized. Higher oxidation activity and Oxygen storage capacity (OSC) were achieved on activated Pt/CZA-T, comparing to Pt catalysts on regular CeO2/Al2O3 (Pt/CA) and one-step prepared CeZrO x /Al2O3 (Pt/CZA). Via the modification of hydrophilic/hydrophobic properties of γ-Al2O3 by this unique T-IWI method, finer Ce0.9Zr0.1O2 particles with higher density of surface defects were formed on CZA-T, on which a higher Pt dispersion and stronger Pt-O-Ce interaction were achieved. Upon activation, smaller, well-dispersed Pt clusters on CZA-T were generated. It was concluded that the CO oxidation performance and OSC were highly related to the size of Pt clusters on different supports that we have developed. More Pt sites located at Pt cluster-CeZrO x interfaces, which were the real active sites, were responsible for the highest OSC function and CO oxidation activity of activated Pt/CZA-T catalyst.

engineering, chemical, environmental

New Insights into the Structure of a CeO2–ZrO2–Al2O3 Composite and Its Influence on the Performance of the Supported Pd-only Three-Way Catalyst

Effect of Ce/Zr Atomic Ratio on the TWC Properties of PdO/CexZr1-xO2(x=0-1.0) Catalysts

CO and Methane Oxidation Over CeXZr1-XO2 Mixed Oxide Supported PdO Catalysts

Preparation of ceria-zirconia by modified coprecipitation method and its supported Pd-only three-way catalyst

Synthesis of a homogeneous CeO2–ZrO2-Al2O3 composite material by a novel hydrothermal assisted precipitation method

Redox properties and metal–support interaction of Pd/Ce0.67Zr0.33O2–Al2O3 catalyst for CO, HC and NOx elimination

Comparative study of three-way catalytic performance over Pd/CeO2-ZrO2-Al2O3 and Pd/La-Al2O3 catalysts: New insights into microstructure and thermal stability

Redox Behavior of Active PdOx Species on (ce,zr)xo2–al2o3 Mixed Oxides and Its Influence on the Three-Way Catalytic Performance

Synthesis of Stable CeO2-ZrO2/Al2O3 Material with Abundant Oxygen Vacancies for Pd-only Three-Way Catalyst Through Two Synergistic Lanthanum Doping Processes

Redox Properties And Metal-Support Interaction Of Pd/Ce0.67zro.3302-Al203 Catalyst For Co, Hc And No Elimination

Morphology Controllable Synthesis of Pd/CeO2–ZrO2 Catalysts and Its Structure-Activity Relationship in Three-Way Catalytic Performance

Three-way catalytic performance of Pd/Ce0.67Zr0.33O2–Al2O3 catalysts: Role of the different Pd precursors

Construction of bimetallic Pt–Pd/CeO2–ZrO2–La2O3 catalysts with different Pt/Pd ratios and its structure–activity correlations for three-way catalytic performance

Preparation of Cex Zr1-x-AI mixed oxides and investigation of the palladium-only three-way catalytic performance

Influence of Ceria-Zirconia Solid Solution on Performance of Noble Metal Monolithic Oxidation Catalyst

Preparation of Ce0.67Zr0.33O2 mixed oxides as supports of improved Pd-only three-way catalysts

Effects of CeO2-ZrO2 Present in Pd/Al2O3 Catalysts on the Redox Behavior of PdOx and Their Combustion Activity

Probing BaO Doping Effect on the Structure and Catalytic Performance of Pd/CexZr1–xO2 (x = 0.2–0.8) Catalysts for Automobile Emission Control

The Support Effect on Pdo/Ce0.7zr0.3ba0.1o2.1 and Cuo/Ce0.7zr0.3ba0.1o2.1 Catalysts

Cerium Based Shells with Palladium Cores Encapsulated: an Efficient Catalyst for Carbon Monoxide Oxidation

Highly efficient Pt catalyst on newly designed CeO2-ZrO2-Al2O3 support for catalytic removal of pollutants from vehicle exhaust