Abstract:T he turbulent in-cylinder air flow and the unsteady high-pressure fuel injection lead to a highly transient air fuel mixing process in spark-ignition directinjection (SIDI) engines, which is the leading cause for combustion cycle-to-cycle variation (CCV) and requires further investigation.In this study, crank-angle resolution particle image velocimetry (PIV) was employed to simultaneously measure the air flow and fuel spray structure at 1300 rpm in an optically accessible single-cylinder SIDI engine.The measurement was conducted at the center tumble plane of the four-valve pent-roof engine, bisecting the spark plug and fuel injector.84 consecutive cycles were recorded for three engine conditions, i.e. (1) none-fueled motored condition, (2) homogeneous-charge mode with start of injection (SOI) during intake (50 crank-angle degree (CAD) after top dead center exhaust, aTDCexh), and (3) stratified-charge mode with SOI during mid compression (270 aTDCexh).The air flow structure (quantified by the objective metric -relevance index) and kinetic energy were examined to study the effect of the fuel spray on the air flow.The air flow was nearly identical for three conditions before the fuel injection.During fuel injection, the entrainment of air into the spray was observed near the spray but the flow structure further away from the spray was not significantly affected for both homogeneous and stratified charge modes.Right after the fuel was atomized, the spray increased the kinetic energy of air f low by 48 ± 25% and 45 ± 40% (average ± standard variation, with CCV included in standard deviation) for spray at intake and compression stroke, respectively.Spray changed the flow structure and kinetic energy immediately after injection for both conditions.The changes caused by injection during intake did not affect the flow and CCV at spark timing.For injection during mid compression, both the flow-structure and kinetic-energy CCV were apparently affected at spark timing.

Characteristics of the In-cylinder Flow and Fuel Behavior with Respect to Fuel Injection Angle and Cone Angle in the PFI Dual Injection Engine

Characteristics of the In-cylinder Flow and Fuel Behavior with Respect to Engine Temperature Condition in the MPI Dual Injection Engine

Experimental Analysis in Dynamics Characteristics of Impinging Spray by a PFI Injector : from Spray Atomization to Fuel Adhesion Formation

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Effect analysis of the forward flow fuel injection angle on stratified combustion process in a high-pressure direct injection diesel Wankel engine (HPDI-DWE)

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Effects of PFI/DI Injection on Stratified Flame Ignition SI-CAIHybrid Combustion

Influence of Early and Late Fuel Injection on Air Flow Structure and Kinetic Energy in an Optical SIDI Engine

Impact Of Fuel Sprays On In-Cylinder Flow Length Scales In A Spark-Ignition Direct-Injection Engine

Computational analysis of piston shape effects on in-cylinder gas flow, fuel-charge mixing, and combustion characteristics in a two-stroke rod-less spark ignition opposed-pistons engine

Development of a Novel Dual-Coil Fuel Injector for Direct-Injection Spark Ignition Engines

A Study on the In-Port Twice Fuel Injection Mode in a 5-Valve S.I.Engine

Dual-injection: the Flexible, Bi-Fuel Concept for Spark-Ignition Engines Fuelled with Various Gasoline and Biofuel Blends

Numerical Investigations of Injection Timing Effects on a Gasoline Direct Injection Engine Performance: Part A, In-Cylinder Combustion Process

Effect of injection strategy on an air-assisted direct injection aviation kerosene two-stroke engine

Investigation of Two-Stage Split-Injection Strategies for a Dieseline Fuelled PPCI Engine

A Piston Geometry and Nozzle Spray Angle Investigation in a DI Diesel Engine by Quantifying the Air-Fuel Mixture

Application of semi-direct fuel injection system to free piston engine generator for better performance: Simulation approach with validation results

CFD Analysis of the Fuel–Air Mixture Formation Process in Passive Prechambers for Use in a High-Pressure Direct Injection (HPDI) Two-Stroke Engine

Numerical Simulation Investigation on Effect of the Different Parameters on the Combustion Pressure and Temperature in a PCCI-DI Engine

Enhancement of Stratified Charge for DISI Engines through Split Injection