Carbon Encapsulated 3D Hierarchical Fe3O4spheres As Advanced Anode Materials with Long Cycle Lifetimes for Lithium-Ion Batteries

Xiulin Fan,Jie Shao,Xuezhang Xiao,Lixin Chen,Xinhua Wang,Shouquan Li,Hongwei Ge

DOI: https://doi.org/10.1039/c4ta01511h

IF: 11.9

2014-01-01

Journal of Materials Chemistry A

Abstract:As anode materials for lithium ion batteries, metal oxides have large storage capacity.

What problem does this paper attempt to address?

Enhanced lithium storage performance in three-dimensional porous SnO 2 -Fe 2 O 3 composite anode films

tianzhi yuan,yinzhu jiang,yong li,dan zhang,mi yan

DOI: https://doi.org/10.1016/j.electacta.2014.05.073

IF: 6.6

2014-01-01

Electrochimica Acta

Abstract:As one of the most promising anode materials in lithium-ion batteries (LIBs), SnO2 attracts wide research attention. The practical application of SnO2 anodes, however, is mainly hampered by huge volume variation during cycling and large initial irreversible capacity. In this paper, three-dimensional porous SnO2-Fe2O3 composite films have been fabricated using the electrostatic spray deposition technique. As an anode for LIBs, the hierarchical porous SnO2-Fe2O3 film possesses a high reversible capacity (1034.1 mAh g-1) and a high initial Coulombic efficiency of 82.9% at a current density of 0.2 A g-1. At the same time, it shows good capacity retention with a capacity of 1025.6 mAh g-1 after 240 cycles and excellent rate performance. The enhanced lithium storage performance should be attributed to the synergistic effect between SnO2 and Fe2O3, as well as the three-dimensional hierarchical porous structure. The results demonstrate that such a three-dimensional porous composite anode shows great potential for application in high-energy lithium-ion batteries.
Fe3O4/C Composites Synthesized from Fe-based Xerogels for Anode Materials of Li-ion Batteries

Xiao Yan Chen,Bin Hong Liu,Zhou Peng Li

DOI: https://doi.org/10.1016/j.ssi.2014.04.004

IF: 3.699

2014-01-01

Solid State Ionics

Abstract:In this study, Fe3O4/carbon nanocomposites as anode materials of Li-ion batteries were synthesized through heating hierarchically porous Fe-based xerogels under N2 atmosphere. The pyrolysis of amorphous Fe-xerogel base materials resulted in the simultaneous formation of Fe3O4/C composites, in which Fe3O4 particles of less than 50nm were uniformly dispersed and embedded in a porous carbon matrix. Due to the favorable nanostructure, the synthesized Fe3O4/C composites with a proper carbon content of 18.8wt.% exhibited good electrochemical performance including high capacity and rate capability as well as much enhanced cyclic stability.
Covalent Organic Framework/Aluminum Oxide Composite Nanosheets As a Separator for High-Performance Lithium–Sulfur Batteries

Bingxin Jia,Hongmin Yu,Zhao Wang,Chan Yao,Wei Xie,Nan Jiang,Shuran Zhang,Yan-Hong Xu,Hao Sun,Ning Huang

DOI: https://doi.org/10.1021/acsapm.4c00572

2024-01-01

ACS Applied Polymer Materials

Abstract:With the depletion of fossil energy and increasingly serious environmental pollution, the development of renewable sources of energy is imminent. Exploration of high-efficiency energy storage and transformation materials has become the focus in the field of energy research. Covalent organic frameworks (COFs), as a kind of porous and crystalline polymer, have attracted extensive attention. In this work, we developed a composite material (Al2O3-G-COFSO3) using COFs and alumina, which can serve as an efficient separator in lithium-sulfur (Li-S) batteries. In the composite, alumina can improve the transport ability of Li+ and thus improve conductivity and SO3-COF can effectively restrain the shuttle of polysulfides by electrostatic repulsion. At a current density of 0.05C, the composite-based battery exhibited a high capacity of 1404 mAh g-1, which ranks as one of the highest values among all of the COF-based Li-S batteries. Even at a discharge rate of 1C, it can also achieve a high experimental capacity of 999 mAh g-1 with a low decay rate of 0.061% over 500 cycles. Moreover, the battery also showed a high electrochemical stability and long-term performance stability.
Carbon-Coated Li3 VO4 Spheres As Constituents of an Advanced Anode Material for High-Rate Long-Life Lithium-Ion Batteries.

Laifa Shen,Shuangqiang Chen,Joachim Maier,Yan Yu

DOI: https://doi.org/10.1002/adma.201701571

IF: 29.4

2017-01-01

Advanced Materials

Abstract:Lithium-ion batteries are receiving considerable attention for large-scale energy-storage systems. However, to date the current cathode/anode system cannot satisfy safety, cost, and performance requirements for such applications. Here, a lithium-ion full battery based on the combination of a Li3 VO4 anode with a LiNi0.5 Mn1.5 O4 cathode is reported, which displays a better performance than existing systems. Carbon-coated Li3 VO4 spheres comprising nanoscale carbon-coating primary particles are synthesized by a morphology-inheritance route. The observed high capacity combined with excellent sample stability and high rate capability of carbon-coated Li3 VO4 spheres is superior to other insertion anode materials. A high-performance full lithium-ion battery is fabricated by using the carbon-coated Li3 VO4 spheres as the anode and LiNi0.5 Mn1.5 O4 spheres as the cathode; such a cell shows an estimated practical energy density of 205 W h kg-1 with greatly improved properties such as pronounced long-term cyclability, and rapid charge and discharge.
3-Dimensional Hierarchically Porous ZnFe2O4/C Composites with Stable Performance As Anode Materials for Li-ion Batteries

Daoyan Feng,Hui Yang,Xingzhong Guo

DOI: https://doi.org/10.1016/j.cej.2018.08.202

IF: 15.1

2018-01-01

Chemical Engineering Journal

Abstract:3-Dimensional hierarchically porous ZnFe2O4/C composites with interconnected macropores and co-continuous hollow skeletons are facilely synthesized and used as anode materials for Li-ion batteries. The interconnected macropores impede the agglomeration of primary particles and buffer the volumetric variations, hollow mesoporous skeletons not only improve the interfacial contact area between electrode and electrolyte but also facilitate lithium ions transfer rate. Moreover, N-doped carbon layer further enhances the conductivity and mechanical strength of skeletons, as well as accelerates electron transfer during repeated discharge and charge process. The as-prepared 3-dimensional hierarchically porous ZnFe2O4/C composites possess excellent Li-ion storage properties, delivering a high reversible capacity of 972 mAh g(-1) at 200 mA g(-1) after 100 cycles and a decent specific capacity of 711 mAh g(-1) even at a large current density of 1000 mA g(-1) after 400 cycles. These values are among the highest reported for ZnFe2O4-based materials with different morphologies and nanostructures. The resultant ZnFe2O4/C composites display the potential practical application for high-performance Li-ion batteries.
Hierarchical dopamine-derived N-doped carbon-encapsulated iron oxide/sulfide hollow nanospheres for enhanced lithium-ion storage

Qi Han,Lu Liu,Haoqian Yu,Dali Mu,Ruiqi Huang,Yifei Wang,Yan Liu,Fuyi Jiang,Yanli Zhou

DOI: https://doi.org/10.1007/s11581-022-04490-x

IF: 2.961

2022-02-27

Ionics

Abstract:Iron-based anode materials have aroused wide attention due to the multiple advantages of high capacity, abundant resources, eco-friendly and low-cost features, whereas the big volume changes upon cycling and low conductivity limit their practical applications. Herein, the dopamine N-doped carbon-encapsulated Fe3O4 and Fe7S8 hollow nanospheres (Fe3O4@NC and Fe7S8@NC) have been designed via a facile synthesis strategy. The hierarchical hollow structure of inner Fe3O4/Fe7S8 restrains the big volume fluctuation upon cycling. The outer tightly wrapped N-doped carbon shell effectively enhances the conductivity of overall electrode and meanwhile serves as the protective layer to inhibit the structure collapse. The strong chemical bonding effects between Fe3O4/Fe7S8 and N-doped carbon construct such stable structures. As expected, both two composites show excellent lithium storage performances owing to the cooperative effect of N-doped carbon shell and internal active material. The reversible capacity of Fe3O4@NC/Fe7S8@NC reaches as high as 830/690 mAh g−1 over 1500/500 loops even at a high rate of 2 A g−1. The excellent electrochemical performances of Fe3O4@NC/Fe7S8@NC demonstrate their potential merits as next-generation anodes for lithium-ion batteries.

chemistry, physical,physics, condensed matter,electrochemistry
Carbon Encapsulated Fe3o4 Nanospheres With High Electrochemical Performance As Anode Materials For Li-Ion Battery

Jiliang Xu,Jian Zhang,Chang-An Wang

DOI: https://doi.org/10.1111/ijac.12722

2017-01-01

International Journal of Applied Ceramic Technology

Abstract:Transformation-type anodes such as Fe3O4 and other transition-metal oxides are gaining popularity in rechargeable Li-ion batteries, but the poor cycling performance and low poor Coulombic efficiency seriously influence their practical applications. Herein, we design a facile method to prepare well-defined yolk-shell Fe3O4@C nanocomposites, and test the nanocomposites as anode material for Li-ion battery. Due to the protection of carbon shell and the loose interspace structure, the capacity of this yolk-shell Fe3O4@C nanocomposites electrode is approximately 860 mAh g(-1) after 300 cycles at 200 mA g(-1) charge/discharge current density with 2 mg cm(-1) loading. The first Coulombic efficiency is about 73.2% and the average Coulombic efficiency is 99% in the following cycles. The remarkably high specific capacity and excellent cycle performance endow the yolk-shell Fe3O4@C nanocomposites as a great potential anode for the Li-ion batteries application.
MOF-derived Fe3O4 hierarchical nanocomposites encapsulated by carbon shells as high-performance anodes for Li-storage systems

Zhuo Li,Xianwei Hu,Bo Li,Xiaoli Wang,Zhongning Shi,Jinlin Lu,Zhaowen Wang

DOI: https://doi.org/10.1016/j.jallcom.2021.159906

IF: 6.2

2021-09-01

Journal of Alloys and Compounds

Abstract:Transition-metal oxides are widely regarded as promising anode materials for lithium-ion batteries (LIBs). However, they suffer from rapid capacity damping which arises from significant volume expansion and poor conductivity during charge-discharge processes. Herein, the metal-organic framework (MOF) derived hierarchical Fe3O4@C nanocomposites coated with carbon were successfully fabricated. Three kinds of Fe-MOF templates with various morphologies were constructed and then carbonized to obtain the corresponding hierarchical Fe3O4@C nanocomposites. Benefiting from the hierarchical core-shell structure, the obtained Fe3O4@C nanocomposites exhibited outstanding electrochemical performance in LIBs. Specifically, the electrodes presented impressive cycling performance (990, 800, and 1180 mAh g-1 after 100 cycles) and outstanding rate stability. Additionally, the Li-storage conversion mechanism and the functional mechanism of coated carbon were identified with in situ electrochemical impedance spectra. This work provides a facile MOF-derived route to design anode materials with a high specific capacity in the energy storage field.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Enhanced Anode Performances Of The Fe3o4-Carbon-Rgo Three Dimensional Composite In Lithium Ion Batteries

Baojun Li,Huaqiang Cao,Jin Shao,Meizhen Qu

DOI: https://doi.org/10.1039/c1cc13462k

IF: 4.9

2011-01-01

Chemical Communications

Abstract:A three dimensional composite was constructed by anchoring Fe3O4 nanoparticles encapsulated within carbon shells onto reduced graphene oxide sheets, which exhibited enhanced anode performances in lithium ion batteries with a specific capacity of 842.7 mAh g(-1) and superior recycle stability after 100 cycles.
Three-dimensionally Porous Fe3O4 As High-Performance Anode Materials for Lithium–ion Batteries

Hao Wu,Ning Du,Jiazheng Wang,Hui Zhang,Deren Yang

DOI: https://doi.org/10.1016/j.jpowsour.2013.07.063

IF: 9.2

2014-01-01

Journal of Power Sources

Abstract:This paper describes the synthesis of three-dimensionally porous Fe3O4 via template-assisted and subsequent electrochemical deposition methods. When used as anode materials of lithium–ion batteries, the porous Fe3O4 electrodes show better cyclability and enhanced rate capabilities compared to planar Fe3O4 electrodes. The superior performance can be attributed to improved electrical contact, fast electron transport and good strain accommodation of the porous electrodes. The effect of the thickness of the porous Fe3O4 electrodes on the lithium–ion battery performance has also been investigated.
3D Porous iron oxide/carbon with large surface area as advanced anode materials for lithium-ion batteries

Chaoyu Duan,Fuliang Zhu,Chen Wang,Xinyou Ke,Guofeng Ren,Yanshuang Meng

DOI: https://doi.org/10.1007/s11581-020-03574-w

IF: 2.961

2020-05-25

Ionics

Abstract:Nanostructures have received great attention to improve the performance of lithium-ion batteries, due to their advantages in dealing with critical issues associated with large volume change, low electrical conductivity, and slow rate of Li+ diffusion. To realize large lithium storage capacity and excellent rate capability of iron oxide electrode. Carbon-modified three-dimensional porous iron oxide was prepared by chemical reaction with in situ formation of templating agent followed by the calcination is reported herein. Benefit from the regulation of the number of pores in the precursor, part of Fe is oxidized to Fe3O4 and part of Fe is peroxidized to Fe2O3, thus forming Fe2O3/Fe3O4 heterostructure during oxidation process. Attributed to its unique structural feature, the 3D Fe2O3/Fe3O4-C heterostructure electrode for the anode of lithium-ion batteries exhibits outstanding rate capability, i.e., 911.4, 797.9, 736.3, 597.8, and 402.6 mAh g−1 at 0.3, 1.0, 2.0, 5.0, and 10.0 A g−1, respectively, and high reversible capacity, i.e., 929.1 mAh g−1 at a low current density of 300 mA g−1.

chemistry, physical,physics, condensed matter,electrochemistry
Three-Dimensional Interconnected Network Geox/Multi-Walled Cnt Composite Spheres As High-Performance Anodes for Lithium Ion Batteries

Wei He,Huajun Tian,Xiaoliang Wang,Fengxia Xin,Weiqiang Han

DOI: https://doi.org/10.1039/c5ta04456a

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:3D GeOx/MWCNTs composite spheres as anode exhibited high rate capability and long-life performances with high areal loading for lithium ion batteries.
Electrosprayed Porous Fe3O4/carbon Microspheres As Anode Materials for High-Performance Lithium-Ion Batteries

Wenjie Han,Xianying Qin,Junxiong Wu,Qing Li,Ming Liu,Yue Xia,Hongda Du,Baohua Li,Feiyu Kang

DOI: https://doi.org/10.1007/s12274-017-1700-6

IF: 9.9

2017-01-01

Nano Research

Abstract:Porous Fe3O4/carbon microspheres (PFCMs) were successfully fabricated via a facile electrospray method and subsequent heat treatment, using ferrous acetylacetonate, carbon nanotubes (CNTs), Ketjen black (KB), polyvinylpyrrolidone (PVP), and polystyrene (PS) as raw materials. The porous carbon sphere framework decorated with well-dispersed CNTs and KB exhibits excellent electronic conductivity and acts as a good host to confine the Fe3O4 nanoparticles. The abundant mesopores in the carbon matrix derived from polymer pyrolysis can effectively accommodate the volume changes of Fe3O4 during the charge/discharge process, facilitate electrolyte penetration, and promote fast ion diffusion. Moreover, a thin amorphous carbon layer on the Fe3O4 nanoparticle formed during polymer carbonization can further alleviate the mechanical stress associated with volume changes, and preventing aggregation and exfoliation of Fe3O4 nanoparticles during cycling. Therefore, as anode materials for lithium-ion batteries, the PFCMs exhibited excellent cycling stability with high specific capacities, and outstanding rate performances. After 130 cycles at a small current density of 0.1 A·g–1, the reversible capacity of the PFCM electrode is maintained at almost 1,317 mAh·g–1. High capacities of 746 and 525 mAh·g–1 were still achieved after 300 cycles at the larger currents of 1 and 5 A·g–1, respectively. The optimized structure design and facile fabrication process provide a promising way for the utilization of energy storage materials, which have high capacities but whose performance is hindered by large volume changes and poor electrical conductivity in lithium or sodium ion batteries.
Self-assembly of Hierarchical Fe3O4microsphere/graphene Nanosheet Composite: Towards a Promising High-Performance Anode for Li-ion Batteries

Ting-qiang Wang,Xiu-li Wang,Yi Lu,Qin-qin Xiong,Xu-yang Zhao,Jian-bin Cai,Sen Huang,Chang-dong Gu,Jiang-ping Tu

DOI: https://doi.org/10.1039/c3ra45268a

IF: 4.036

2014-01-01

RSC Advances

Abstract:A hierarchical Fe3O4 microsphere/graphene nanosheet (H-Fe3O4-MS/GNS) composite has been synthesized by a facile one-pot solvothermal route. The Fe3O4 microspheres uniformly decorated the surface of the two dimensional GNS. Each Fe3O4 microsphere possesses a hierarchical and porous structure, which is composed of Fe3O4 nanoparticles with a diameter of about 10 nm. As an anode material for Li-ion batteries, the H-Fe3O4-MS/GNS composite shows high specific capacity and good cycling stability (1171.6 mA h g(-1) at 200 mA g(-1) and 940.4 mA h g(-1) at 500 mA g(-1) up to 70 cycles), reduced voltage hysteresis, as well as enhanced rate capability. The improved electrochemical performance can be attributed to the combination of the conductivity, confinement and dispersion effects of GNS and the porous hierarchical structure of the Fe3O4 microsphere.
MOF-Derived Hierarchical MnO-Doped Fe3O4@C Composite Nanospheres with Enhanced Lithium Storage.

Zhishun He,Kai Wang,Shasha Zhu,Liang-ai Huang,Miaomiao Chen,Jianfeng Guo,Shien Pei,Haibo Shao,Jianming Wang

DOI: https://doi.org/10.1021/acsami.8b01358

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:Hierarchically nanostructured binary/multiple transition-metal oxides with electrically conductive coatings are very attractive for lithium-ion batteries owing to their excellent electrochemical properties induced by their unique compositions and microstructures. Herein, hierarchical MnO-doped Fe3O4@C composite nanospheres are prepared by a simple one-step annealing in Ar atmosphere, using Mn-doped Fe-based metal-organic frameworks (Mn-doped MIL-53(Fe)) as precursor. The MnO-doped Fe3O4@C composite particles have a uniform nanosphere structure with a diameter of ∼100 nm, and each nanosphere is composed of clustered primary nanoparticles with an amorphous carbon shell, forming a unique hierarchical nanoarchitecture. The as-prepared hierarchical MnO-doped Fe3O4@C composite nanospheres exhibit markedly enhanced lithium-storage performance, with a large capacity of 1297.5 mAh g-1 after 200 cycles at 200 mA g-1. The cycling performance is clarified through analyzing the galvanostatic discharge/charge voltage profiles and electrochemical impedance spectra at different cycles. The unique microstructures and Mn element doping of the hierarchical MnO-doped Fe3O4@C composite nanospheres lead to their enhanced lithium-storage performance.
Synthesis of Hierarchical Hollow-Structured Single-Crystalline Magnetite (fe3o4) Microspheres: the Highly Powerful Storage Versus Lithium As an Anode for Lithium Ion Batteries

Q. Q. Xiong,J. P. Tu,Y. Lu,J. Chen,Y. X. Yu,Y. Q. Qiao,X. L. Wang,C. D. Gu

DOI: https://doi.org/10.1021/jp3002178

2012-01-01

The Journal of Physical Chemistry C

Abstract:Hierarchical hollow Fe3O4 (H-Fe3O4) microspheres are 'prepared by the controlled thermal decomposition of an iron alkoxide precursor, which is obtained via an ethylene glycol (EG) mediated solvothermal reaction of ferric chloride hexahydrate (FeCl3 center dot 6H(2)O), sodium acetate (NaAc), and polyvinylpyrrolidone (PVP). The microspheres are characterized by the assembly of highly oriented primary nanoparticles and have a single-crystal feature. As the anode materials for the lithium-ion batteries, the resultant H-Fe3O4 microspheres show high specific capacity and good cycle stability (851.9 mAh g(-1) at 1 C and 750.1 mAh g(-1) at 3 C up to 50 cycles), as well as enhanced rate capability. The excellent electrochemical performance can be attributed to the high interfacial contact area between the microspheres and electrolyte, and good accommodation of volume change arising from the synergetic effect of the hierarchical hollow structure. It is suggested that the H-Fe3O4 microsphere synthesized by this method is a promising anode material for high energy-density lithium-ion batteries.
Fe3O4 Hollow Nanospheres Grown In Situ in Three-Dimensional Honeycomb Macroporous Carbon Boost Long-Life and High-Rate Lithium Ion Storage

Lixia Wang,Hao Zheng,Xin Jin,Yongfeng Yuan

DOI: https://doi.org/10.1007/s11664-022-10026-w

IF: 2.1

2022-11-04

Journal of Electronic Materials

Abstract:A composite of Fe 3 O 4 and carbon is constructed by a one-step calcination method with polystyrene spheres as template, polyvinyl pyrrolidone as assembling agent, and Fe(NO 3 ) 3 as Fe source. Material characterization demonstrates that Fe 3 O 4 hollow nanospheres 10–16 nm in diameter are closely grown in situ inside three-dimensional honeycomb macroporous carbon with a pore diameter of about 200 nm. The composite material exhibits high specific capacity, delivering an average discharge capacity of 1618 mA h g −1 at 0.1 A g −1 . The long-term cycling performance is excellent, achieving discharge capacity of 770 mA h g −1 at 1 A g −1 after 1000 cycles and 429 mA h g −1 at 5 A g −1 after 200 cycles. Even at 10 A g −1 , the rate capability is outstanding. Kinetics analyses reveal predominant capacitive behavior and low reaction impedance in electrochemical reaction. The excellent performance mainly benefits from the beneficial structural effects of Fe 3 O 4 hollow nanospheres and honeycomb macroporous carbon. Fe 3 O 4 hollow nanospheres@three-dimensional honeycomb macroporous carbon is a superior anode material for lithium-ion batteries.

engineering, electrical & electronic,materials science, multidisciplinary,physics, applied
Ultrathin Li4Ti5O12 Nanosheet Based Hierarchical Microspheres for High-Rate and Long-Cycle Life Li-Ion Batteries

Yishi He,Aidaer Muhetaer,Jianming Li,Feifan Wang,Cheng Liu,Qi Li,Dongsheng Xu

DOI: https://doi.org/10.1002/aenm.201700950

IF: 27.8

2017-01-01

Advanced Energy Materials

Abstract:Ultrathin Li4Ti5O12 nanosheet based hierarchical microspheres are synthesized through a three-step hydrothermal procedure. The average thickness of the Li4Ti5O12 sheets is only approximate to(6.6 +/- 0.25) nm and the specific surface area of the sample is 178 m(2) g(-1). When applied into lithium ion batteries as anode materials, the hierarchical Li4Ti5O12 microspheres exhibit high specific capacities at high rates (156 mA h g(-1) at 20 C, 150 mA h g(-1) at 50 C) and maintain a capacity of 126 mA h g(-1) after 3000 cycles at 20 C. The results clearly suggest that the utility of hierarchical structures based on ultrathin nanosheets can promote the lithium insertion/extraction reactions in Li4Ti5O12. The obtained hierarchical Li4Ti5O12 with ultrathin nanosheets and large specific surface area can be perfect anode materials for the lithium ion batteries applied in high power facilities, such as electric vehicles and hybrid electric vehicles.
Rosa roxburghii-like hierarchical hollow sandwich-structure C@Fe2O3@C microspheres as second nanomaterialsfor superior lithium storage

Mengfei Sun,Xianfeng Chu,Zhenkang Wang,Hongxun Yang,Zhao Yang,Jiaojiao Ma,Bo Zhou,Tongyi Yang,Lizhuang Chen

DOI: https://doi.org/10.1016/j.jallcom.2020.157518

IF: 6.2

2021-02-01

Journal of Alloys and Compounds

Abstract:Fe2O3, as a promising advanced anode for the next generation lithium ion batteries, behaves high theoretical capacity and rich electrochemical properties. However, the poor cycle performances and low conductivity impede its extensive applications in lithium ion batteries. Herein, the von Mises stress distribution on solid spheres and hollow spheres were simulated by finite element method which confirmed the vital role of porous hollow spheres on strain-relaxation behavior as electrode materials. We also have developed a template method for the first preparation of rosa roxburghii-like hierarchical hollow sandwiched 2O3@C microspheres as second nanomaterials for superior lithium storage. As an advanced anode for lithium ion batteries, the porous 2O3@C microspheres exhibit reversible gravimetric capacity (1167 mAh g−1 after 100 cycles at 0.2 C), high rate performance (762 mAh g−1 after 1000 cycles at 1 C) and cycling stability without obvious capacity fading. The excellent performance is ascribed to the hierarchical hollow structure which can better withstand the stress produced in the process of ion embedding/stripping and alleviate the volume change of materials. On the other hand, the double carbon layer can effectively inhibit the self-aggregation effect of nano-scale Fe2O3 and provide a three-dimensional electronic network.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Hierarchical Fe3O4@C Nanospheres Derived from Fe2O3/MIL-100(Fe) with Superior High-Rate Lithium Storage Performance

Kai Wang,Miaomiao Chen,Zhishun He,Liang-ai Huang,Shasha Zhu,Shien Pei,Jianfeng Guo,Haibo Shao,Jianming Wang

DOI: https://doi.org/10.1016/j.jallcom.2018.04.320

IF: 6.2

2018-01-01

Journal of Alloys and Compounds

Abstract:Carbon coating is one of the most effective strategies to improve the electrochemical performance of nanostructured transition metal oxides (TMOs). Herein, we report a facile and scalable method to prepare hierarchical Fe3O4@C nanospheres. The fabrication includes one-step solvothermal synthesis of Fe2O3/MIL-100(Fe) precursor and subsequent annealing treatment in Ar. The Fe3O4 @C nanospheres with an average size of about 200 nm are composed of many interconnected small nanoparticles, with an amorphous carbon layer on the surface of Fe3O4, exhibiting a unique hierarchical nanostructure with a larger specific surface area of 176.5 m(2) g(-1). The hierarchical Fe3O4@C nanosphere electrode delivers a high capacity of 757.9 mAh g(-1) after 500 cycles at a current density of 500 mA g(-1), demonstrating superior high-rate lithium storage performance. This may be ascribed to the unique hierarchical nanoarchitecture, higher specific surface area and the uniform carbon layer in-situ generated from MIL100(Fe). (C) 2018 Elsevier B.V. All rights reserved.

Carbon Encapsulated 3D Hierarchical Fe3O4spheres As Advanced Anode Materials with Long Cycle Lifetimes for Lithium-Ion Batteries

Enhanced lithium storage performance in three-dimensional porous SnO 2 -Fe 2 O 3 composite anode films

Fe3O4/C Composites Synthesized from Fe-based Xerogels for Anode Materials of Li-ion Batteries

Covalent Organic Framework/Aluminum Oxide Composite Nanosheets As a Separator for High-Performance Lithium–Sulfur Batteries

Carbon-Coated Li3 VO4 Spheres As Constituents of an Advanced Anode Material for High-Rate Long-Life Lithium-Ion Batteries.

3-Dimensional Hierarchically Porous ZnFe2O4/C Composites with Stable Performance As Anode Materials for Li-ion Batteries

Hierarchical dopamine-derived N-doped carbon-encapsulated iron oxide/sulfide hollow nanospheres for enhanced lithium-ion storage

Carbon Encapsulated Fe3o4 Nanospheres With High Electrochemical Performance As Anode Materials For Li-Ion Battery

MOF-derived Fe3O4 hierarchical nanocomposites encapsulated by carbon shells as high-performance anodes for Li-storage systems

Enhanced Anode Performances Of The Fe3o4-Carbon-Rgo Three Dimensional Composite In Lithium Ion Batteries

Three-dimensionally Porous Fe3O4 As High-Performance Anode Materials for Lithium–ion Batteries

3D Porous iron oxide/carbon with large surface area as advanced anode materials for lithium-ion batteries

Three-Dimensional Interconnected Network Geox/Multi-Walled Cnt Composite Spheres As High-Performance Anodes for Lithium Ion Batteries

Electrosprayed Porous Fe3O4/carbon Microspheres As Anode Materials for High-Performance Lithium-Ion Batteries

Self-assembly of Hierarchical Fe3O4microsphere/graphene Nanosheet Composite: Towards a Promising High-Performance Anode for Li-ion Batteries

MOF-Derived Hierarchical MnO-Doped Fe3O4@C Composite Nanospheres with Enhanced Lithium Storage.

Synthesis of Hierarchical Hollow-Structured Single-Crystalline Magnetite (fe3o4) Microspheres: the Highly Powerful Storage Versus Lithium As an Anode for Lithium Ion Batteries

Fe3O4 Hollow Nanospheres Grown In Situ in Three-Dimensional Honeycomb Macroporous Carbon Boost Long-Life and High-Rate Lithium Ion Storage

Ultrathin Li4Ti5O12 Nanosheet Based Hierarchical Microspheres for High-Rate and Long-Cycle Life Li-Ion Batteries

Rosa roxburghii-like hierarchical hollow sandwich-structure C@Fe2O3@C microspheres as second nanomaterialsfor superior lithium storage

Hierarchical Fe3O4@C Nanospheres Derived from Fe2O3/MIL-100(Fe) with Superior High-Rate Lithium Storage Performance