Abstract:The performance of superconducting magnets is greatly dependent on the size and uniformity of the superconducting filaments within the wire. However, in the fabrication of Bi 2 Sr 2 CaCu 2 O x (Bi2212) wires using ceramic oxide as the superconducting filaments, we face multiple challenges including filament fragility, poor uniformity, and non-smooth Ag/superconductor interfaces. These challenges primarily stem from the significantly lower plastic deformation capability of ceramic oxide powder filaments compared to metal matrices. To address these challenges, this study focuses on the modification of ceramic oxide precursor powders. Through the utilization of low-temperature, low oxygen partial pressure ( p O 2 ) heat treatment, we have observed significant changes in the Cu chemical states and lattice parameters within the Bi2212 grains. These alterations have proven to be highly effective in reducing the energy required for grain sliding and, in turn, enhancing the plastic deformation properties of the Bi2212 oxide filament. Furthermore, post-annealing the oxide powder under low p O 2 conditions narrows the gap in plastic deformability between the Ag sheath and the oxide filaments, resulting in improved filament uniformity and a smoother Ag/oxide interface in Bi2212 wires. Notably, the Bi2212 grains exhibit an orderly arrangement within the wires. As a result of these improvements, the critical current density ( J c ) of the final wires increases by an impressive 70 %. The outcomes of this study are not only crucial for producing Bi2212 magnets with higher magnetic field strength, improved magnetic field uniformity, and enhanced operational stability, but also offer fresh insights and methodologies for advancing the field of superconducting materials.

Optimization of Intergrain Connection in High-Temperature Superconductor Bi2sr2cacu2ox

Development of a Novel Fabrication Technique for High-Quality Bi-2223 Bulks with High Superconducting Performance

Optimized Intergrain Connection and Transport Properties of Bi-2212 High-Temperature Superconductors by Ag Nanoparticles Inclusions

Enhancement of Bi-2223 Intergrain Connections by Heat Treatment Parameters Optimization

Synergism Effect of Pb Doping and Microstructure Optimization on the Superconducting Properties of Bi-2212 Ceramics

Optimization of Current Carrying Capacity in Bi-2212 High Temperature Superconductors

Optimization of Bi-2212 High Temperature Superconductors by Potassium Substitution

Fabrication and Optimization of Bi-2212 High Temperature Superconductors with K and Ag Co-Incorporation

Density Enhancement for the Fabrication of Bi-2212 Superconducting Tapes

Improvements of Superconducting Properties on Bi-2212 Bulks by Element Doping

Enhanced Flux Pinning Properties in Bi-2212 High Temperature Superconductors with Nano-Sized Precipitates

Influences of Ca Nonstoichiometry on the Superconducting Properties of Bi-2212 Superconducting Bulks

Fabrication of Multifilamentary Powder in Tube Superconducting Tapes of Bi-2223 with Sr Deficient Starting Composition

Improving Transport Properties of Bi-2223 Superconducting Tapes with the Optimization of Packing Atmosphere

Improved Grain Connectivity and Critical Current Density in Ex-Situ MgB2 Superconductors Prepared by Two-Step Sintering

Influence of Cu Content in Precursor Powders on the Phase Evolution and Superconducting Properties of Bi-2212 Superconductors

Influence of Precursor Powder Fabrication Methods on the Superconducting Properties of Bi-2223 Tapes

Effects of Controlled Over-Pressure Sintering on the Critical Current and Mechanical Properties of Bi-2223/Ag Tape

Improvement of plastic deformation property and current carrying capacity of Bi2212 wires through low oxygen partial pressure post-annealing of precursor

Influences of Na Doping on Superconducting Properties of Bi-2212 High Temperature Superconductors

Influences of Yb substitution on the intergrain connections and flux pinning properties of Bi-2212 superconductors