Abstract:AZ31 magnesium alloy has poor plastic deformation ability at room temperature due to its hexagonal close-packed (HCP) structure. For traditional plastic forming processes, such as extrusion processes, they can improve the mechanical properties of AZ31 magnesium alloy within a certain range at room temperature. But the coordinated deformation of twin mechanism cannot be neglected during the plastic deformation process. The mechanical properties of AZ31 magnesium alloy exhibit tension–compression yield asymmetry (TCYA). These characteristics of AZ31 magnesium alloy have caused restrictions. As a short forming/preparing integrated process, CVCDE can increase the yield strength (YS) of AZ31 magnesium alloy while effectively improving the TCYA of AZ31 magnesium alloy. In this study, the uniaxial compression test is employed and the quantitative evaluation of the AZ31 magnesium alloy TCYA is carried out by means of the SDE coefficient. With the aid of scanning electron microscopes (SEM) and electron backscattered diffraction (EBSD), the test results indicate that the fracture morphology has changed significantly with the increase in CVCDE interim. The distribution of tear ridges in the fracture area tends to be uniform and the number of dimples increases significantly. The dimples also present a trend of deepening. From the twin distribution, the proportion of {10-12} tensile twins (TTWs) decreased after the AZ31 magnesium alloy processed by CVCDE. This is conducive to the YS in the compression process and the improvement of the TCYA can be obtained.

Tensile anisotropy of AZ91 magnesium alloy by equal channel angular processing

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Mechanical properties and structure of AZ61 magnesium alloy processed by equal channel angular pressing

Orientation factor analysis of deformation mechanisms under special processing techniques in AZ31 magnesium alloys

Investigation on the anisotropy of mechanical properties along different orientations of an AZ31 hot-extrusion bar

Texture modification and mechanical properties of AZ31 magnesium alloy sheet subjected to equal channel angular bending

Microstructural evolution and mechanical properties of AZ31 Mg alloy fabricated by a novel bifurcation-equal channel angular pressing

Precipitation behaviors and mechanical properties of a solution-treated Mg-Gd-Nd-Zn-Zr alloy during equal-channel angular pressing process

Study of strength-ductility and anisotropic behavior of Mg-Gd-Y-Zn-Zr alloy prepared by Equal channel double angular pressing

Extraordinary mechanical properties of AZ61 alloy processed by ECAP with 160° channel angle and EPT

Mechanical Properties and Constitutive Analysis of Extruded AZ31B Magnesium Alloy

Mixed Grain Structure and Mechanical Property Anisotropy of AZ40 Magnesium Alloy Bar with Diameter of 160 Mm

Tailoring Mechanical Properties of Mg–Al–Zn–Sn–Mn Alloy by Multipass Equal Channel Angular Pressing

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

Mechanical Properties and Microstructure of AZ31B Magnesium Alloy Processed by I-ECAP

Effect of equal channel angular extrusion process on deformation behaviors of Mg-3Al-Zn alloy

Anisotropy investigation of an ECAP-processed Mg-Al-Ca-Mn alloy with synergistically enhanced mechanical properties and corrosion resistance

Mechanical Properties and Microstructure of AZ31 Mg Alloy Processed by Two-Step Equal Channel Angular Extrusion

Evading Strength-Ductility Tradeoff in Mg Alloy via Uniform Microstructure and Unique Texture Modification Induced by Moderate Temperature ECAP

Strengthening Mechanism of Room Temperature Mechanical Properties for AZ31 Magnesium Alloy by Continuous Variable Cross section Direct Extrusion

Experiment and Modeling of Plastic Anisotropy for AZ31B Mg-Alloy