Microstructure coarsening behavior of Ti-17 alloy with equiaxed alpha during heat treatment

jianwei xu,weidong zeng,zhiqiang jia,xin sun,jianhua zhou

DOI: https://doi.org/10.1016/j.jallcom.2014.08.223

IF: 6.2

2015-01-01

Journal of Alloys and Compounds

Abstract:Curves of r‾αn-r‾α0n vs t−t0 for material heat treated at 820°C and 860°C, and values of n equal to (a) 1, (b) 2, (c) 3 and (d) 4.

What problem does this paper attempt to address?

Coarsening Behavior of Lamellar Microstructure of TC17 Titanium Alloy During Heating Processing in α+β Phase Field

Yunli Wang,Xingdong Zhao,Jianwei Xu,Weidong Zeng

DOI: https://doi.org/10.13567/j.cnki.issn1009-9964.2018.03.008

2018-01-01

Abstract:The coarsening behavior of TC17 titanium alloy at 800℃and 840℃was investigated in this research.The results show that the thickness of alpha lamellae continues to increase with heat treatment time .However, the coarsening rate decreases with heat treatment time.The coarsening of alpha lamellae is a process of element diffusion. Elements will migrate from the large curvature (the termination or defect position ) to the small curvature (the flat interface), which leads to the dissolution of the termination tip and the coarsening of the adjacent plate.The coarsening index is calculated as 0.37 and 0.42 for 800 ℃and 840 ℃.According to the LSW theory, the coarsening behavior of TC17 titanium alloy is controlled by bulk diffusion and interface reaction.The prediction model of coarsening rate of TC17 titanium alloy is successfully established based on Gibbs-Thompson theory.
Microstructure evolution during isothermal forging and subsequent heat treatment of Ti-17 alloy with a lamellar colony structure

jianwei xu,weidong zeng,xin sun,zhiqiang jia

DOI: https://doi.org/10.1016/j.jallcom.2015.03.042

IF: 6.2

2015-01-01

Journal of Alloys and Compounds

Abstract:•The rotation and fragmentation characterize alpha phase during deformation.•The preferential orientation of alpha phase after deformation is about 90°.•The separation of alpha phase and coarsening are two features during heat treatment.•The coarsening and shortening of alpha phase during heat treatment were quantified.
Coarsening Kinetics and Morphological Evolution in a Two-Phase Titanium Alloy During Heat Treatment

Jianwei Xu,Weidong Zeng,Zhiqiang Jia,Xin Sun,Yawei Zhao

DOI: https://doi.org/10.1007/s11665-016-1951-5

IF: 2.3

2016-01-01

Journal of Materials Engineering and Performance

Abstract:The effects of alpha/beta heat treatment on microstructure evolution of Ti-17 alloy with a lamellar colony structure are established. Heat treatment experiments are conducted at 1103 or 1063 K for times ranging from 10 min to 8 h. The main features of microstructure evolution during heat treatment comprise static globularization and coarsening of primary alpha phase. Such behaviors can be accelerated by higher heat treatment temperature. Furthermore, globularization and coarsening behaviors show a faster rate at higher prestrain. In order to better understand the microstructure evolution of Ti-17 alloy during alpha/beta heat treatment, static globularization and coarsening behaviors are modeled in the theoretical frame of the Johnson-Mehl-Avarmi-Kolmogorov (JMAK) and Lifshitz-Slyozov-Wagner (LSW) theories, respectively. The JMAK and LSW kinetics parameters are derived under different experimental conditions. Agreements between measurements and predictions are found, indicating that the JMAK and LSW theories can be used to predict and trace static globularization and coarsening processes of Ti-17 alloy during alpha/beta heat treatment.
Static Coarsening Behavior of the Lamellar Alpha in Ti-17 Alloy

Jianwei Xu,Weidong Zeng,Xin Sun,Zhiqiang Jia,Jianhua Zhou

DOI: https://doi.org/10.1016/j.jallcom.2015.01.106

IF: 6.2

2015-01-01

Journal of Alloys and Compounds

Abstract:Static coarsening behavior of Ti-17 alloy with the lamellar alpha structure has been investigated as a function of time at temperatures of 820 degrees C and 860 degrees C. The resultant microstructures have been characterized using scanning electron microscopy. Microstructure prior to heat treatment contained a fully lamellar alpha structure. Heat treatment at 820 degrees C and 860 degrees C resulted in the continuous coarsening of alpha lamellae. The coarsening rate decreases with heat treatment time. Static coarsening of Ti-17 alloy with the lamellar alpha was mainly controlled by termination migration mechanism. Solute atoms migrated from the termination or local defect positions of lamellae to the flat interface, leading to the coarsening or separation of the lamellar alpha. The coarsening behavior could be interpreted in terms of Lifshitz-Slyozov-Wagner (LSW) theory, and the kinetics equation could be established by the modified LSW theory model (d = Kt(n)). The coarsening coefficients n of Ti-17 alloy with the lamellar structure were determined to 0.33-0.4 for 820 degrees C and 0.45-0.5 for 860 degrees C, respectively. Therefore, the coarsening was more likely influenced by bulk diffusion at 820 degrees C, and controlled by interface reaction at 860 degrees C. In addition, a mathematical model was developed to predict static coarsening rate of the lamellar alpha of Ti-17 alloy. The results showed that the model can provide a relatively reliable prediction for static coarsening behavior of the lamellar structure of Ti-17 alloy. (C) 2015 Elsevier B.V. All rights reserved.
Microstructural Instability of A Tial-Based Alloy During Rapid Heating Cyclic Heat Treatment

CQ Peng,BY Huang

DOI: https://doi.org/10.3321/j.issn:1002-185x.2004.04.006

2004-01-01

Rare Metal Materials and Engineering

Abstract:Four kinds of microstructural instability of a TiAl-based alloy during rapid heating cyclic heat treatment were observed: (i) the formation of secondary lamellae, (ii) the spheroidization of primary lamellae, (iii) a discontinuous coarsening at grain boundaries and (iv) nucleation at phase interfaces. By comparing the starting line of continuous heating transformation with that of TTT diagram, the similarity and difference of the microstructure instability during continuous heating and isothermal heating conditions were studied. Ways of avoiding unfavorable microstructural instability were proposed such as: (i) insuring homogeneity of the composition so as to guarantee the identity of transformation temperature in the alloy; (ii) holding at the highest temperature for as short a time as possible.
Microstructural Evolution of A Forged Tial Based Alloy During Heat Treatment at Subtransus Temperature

JC Tang,BY Huang,WS Liu,YH He

IF: 3.752

2000-01-01

Transactions of Nonferrous Metals Society of China

Abstract:Microstructural evolution of a forged TiAl based alloy during heat treatment from 1180 degrees C to 1300 degrees C was investigated. The grain sizes of the alpha phases as well as the sizes and the volume fractions of the gamma phases were evaluated as a function of heat treatment temperature and time. When the alloys are isothermally heat treated at subtransus temperatures, the sizes of gamma phases( D-gamma) increase slightly with heat treatment temperature and time and those of alpha phases(D-alpha) and the volume fractions of gamma phases(phi gamma) vary significantly with holding time in the early stages of heat treatments, but after heat treatments for 2h, phi gamma reveal little variations with holding times and D-alpha approach limits, which can be described by D-alpha 0 = 0. 65 D-gamma/(phi gamma). Besides, it has been found that the alpha phases in the specimens heat treated at 1260 degrees C and 1300 degrees C contain lamellar structures, at low temperatures, however, appear featureless.
Experimental investigation of coarsening behavior of TA15 titanium alloy in beta-phase field

Chuan Wu,He Yang,Hongwei Li,Zhichao Sun

2012-01-01

Abstract:The coarsening characteristics of TA15 titanium alloy with an equiaxed microstructure were investigated via experimental study. The experiments were performed at temperatures of 1273,1293,1313,1333 and 1353 K for holding times 5,10,20 and 30 minutes at each temperature, respectively. To understand and control the coarsening behavior, the effects of temperature and holding time(t) on the growth kinetics and topological features were experimentally investigated. We find that temperature does have an important effect on grain coarsening in beta-phase field. At the experimental temperatures, we neglect the effect of initial grain size R-o on coarsening evolution. The relationship between average grain size(R) and t approximately follows the classical parabolic growth law, moreover, the growth exponent (m) does not vary at specific temperatures; the areas of grains with sides less and more than six linearly decrease and increase with t, respectively; the distribution of grain size and edges is initial grain size-invariant and time-invariant under these temperatures.
Microstructure and Mechanical Properties of TC21 Titanium Alloy after Heat Treatment

Zhi-feng Shi,Hong-zhen Guo,Jin-yang Han,Ze-kun Yao

DOI: https://doi.org/10.1016/s1003-6326(13)62810-1

IF: 3.752

2013-01-01

Transactions of Nonferrous Metals Society of China

Abstract:Microstructure evolutions during different heat treatments and influence of microstructure on mechanical properties of TC21 titanium alloy were investigated. The results indicate that the excellent mechanical properties can be obtained by adopting air cooling after forging followed by heat treatment of (900 °C, 1 h, AC)+(590 °C, 4 h, AC). Deformation in single β field produces pan-like prior β grains, while annealing in single β field produces equiaxed prior β grains. Cooling rate after forging or annealing in single β field and the subsequent annealing on the top of α+β field determine the content and morphology of coarse α plates. During aging or the third annealing, fine secondary α plates precipitate. Both ultimate strength and yield strength decrease with the content increase of coarse α plates. Decreasing effective slip length and high crack propagation resistance increase the plasticity. The crisscross coarse α plates with large thickness are helpful to enhance the fracture toughness.
Evolution of the microstructure of as-rolled Ti-43AI-9V-Y alloy with different heat treatments

Fantao Kong,Yuyong Chen

2009-01-01

Abstract:The as-rolled Ti-43Al-9V-Y alloy sheet material investigated had a starting microstructure consisting of equiaxed gamma grains with a small volume fraction of B2 phase mainly located in gamma grain boundaries. As-rolled samples were heat treated at different temperatures ranging from 1200 degrees C up to 1320 degrees C. The hold time at these temperatures was 30 minutes. After different heat treatment, the equiaxed gamma grain size of the sheet does not increase dramatically but precipitation of B2 phase lamellas in equiaxed gamma grains is observed upon furnace cooling. Furthermore, after heat treatment at 1280 degrees C, gamma equiaxed grains were refined because the content of B2 laths formed in gamma equiaxed grains increased significantly. Microstructure of Ti-43Al-9V-Y alloy sheet transferred from gamma+B2 phase microstructure to DP microstructure after heat treatment of 1300 degrees C /30min. And after heat treatment at 1320 degrees C, many gamma equiaxed grains had been also changed into alpha 2/gamma/B2 lamellar structure, and the content of B2 phase of like-network shape increased.
Microstructure Evolution of Rapidly Solidified Ti3al-2nb Alloy

R Xu,YY Cui,D Li,ZQ Hu,DM Xu,QC Li

1996-01-01

Abstract:It has been found from the analysis of X-ray diffraction and the observation of TEM that the metastable ordered orthorhombic martensite alpha(0) '' phase in the rapidly solidified Ti3Al-2Nb alloy transforms to various phases at different aging temperatures. When the alloy aged at temperature of 500 degrees C for 20 min, the alpha(0) '' phase decomposition into B2 and O phases is related to the stress in the alloy. When the aged temperature above 600 degrees C, the alpha(0) '' phase transforms to alpha(2) phase by both shearing and chemical ordering.
Evolutions of the Microstructures and Mechanical Properties of Ti-2.8 Wt%cu Alloy During Heat Treatment

Shengnan Ma,Xin Hu,Chaoqiang Liu,Shijia Qiu,Min Song

DOI: https://doi.org/10.1016/j.jallcom.2023.172568

IF: 6.2

2023-01-01

Journal of Alloys and Compounds

Abstract:The evolutions of the microstructures and mechanical properties of Ti-2.8Cu (wt%) alloy during heat treatment were investigated in this study using X-ray diffraction and electron microscopes. Three typical microstructures including alpha + Ti2Cu, alpha + alpha ' and single alpha ' were obtained after solution treatment at 780 degrees C for 4 h, 850 degrees C for 2 h and 950 degrees C for 1 h, respectively. With an increase in the solution temperature, the mechanical strength of the alloy was enhanced while the elongation was decreased. When the alloy with different microstructures was isothermally aged at 450 degrees C for 15 h or 550 degrees C for 15 h, a few of precipitates were observed in alpha phase that has a low Cu content and a large number of disk-shaped Ti2Cu precipitates were detected in alpha ' martensite that has a high Cu content. Most of the Ti2Cu precipitates lie on {1101}alpha ' except that a few of them can be occasionally detected on {1103}alpha ' in samples aged at 450 degrees C for 15 h, while all of the Ti2Cu precipitates lie on {1103}alpha ' in samples aged at 550 degrees C for 15 h. The Ti2Cu precipitates lying on {1101}alpha ' are thinner and denser than that lying on {1103}alpha ', which can cause a better precipitation strengthening effect in the alloy. For this reason, the sample solutionized at 950 degrees C for 1 h and then aged at 450 degrees C for 15 h has the highest yield strength of 907.8 MPa.
Evolution Laws of Microstructures and Mechanical Properties During Heat Treatments for Near-Α High-Temperature Titanium Alloys

Ma Xiaozhao,Xiang Zhilei,Li Tao,Chen Yilan,Liu Yingying,Chen Ziyong,Shu Qun

DOI: https://doi.org/10.1007/s12613-021-2248-8

2022-01-01

International Journal of Minerals Metallurgy and Materials

Abstract:Evolution laws of microstructures, mechanical properties, and fractographs after different solution temperatures were investigated through various analysis methods. With the increasing solution temperatures, contents of the primary α phase decreased, and contents of transformed β structures increased. Lamellar α grains dominated the characteristics of transformed β structures, and widths of secondary α lamellas increased monotonously. For as-forged alloy, large silicides with equiaxed and rod-like morphologies, and nano-scale silicides were found. Silicides with large sizes might be（Ti, Zr, Nb） 5 Si 3 and（Ti, Zr, Nb） 6 Si 3 . Rod-like silicides with small sizes precipitated in retained β phase, exhibiting near 45° angles with α/β boundaries. Retained β phases in as-heat treated alloys were incontinuous. 980STA exhibited an excellent combination of room temperature（RT） and 650°C mechanical properties. Characteristics of fracture surfaces largely depended on the evolutions of microstructures. Meanwhile, silicides promoted the formation of mico-voids.
Quantitative Relationships Between Mechanical Properties and Microstructure of Ti17 Alloy after Thermomechanical Treatment

Yan Han,Fei Zhao,Yuan Liu,Chaowen Huang

DOI: https://doi.org/10.3390/met10010067

IF: 2.695

2020-01-01

Metals

Abstract:In this paper, the relationships between the thermomechanical treatments (TMT), the microstructural evolution the mechanical properties of Ti17 alloy were investigated. The results indicate the coarsening behavior of lamellar α was sensitive to the aging temperature during the process of TMT. The thickness of lamellar α changed from 0.19 to 0.38 μm with an increase in the aging temperature. Moreover, both tensile properties and impact toughness vary with the thickness of lamellar α. The tensile strength increases with the increase of the thickness of lamellar α the plasticity and impact toughness the opposite trend. The quantitative investigations found that there is a linear relationship between the tensile properties and the thickness of lamellar α the tensile properties could be adjusted in the range of 1191~1062 MPa and 1163~1039 MPa to obtain ultimate tensile strength and yield strength as well as 11~16% elongation and 23~33% reduction of area by varying the thickness of lamellar α. Meanwhile, the impact toughness could be adjusted in the range of 46 ~53 J/cm2. The high correlation coefficients imply that the linear equation is reliable to describe the relationships between the mechanical properties and the thickness of lamellar α for Ti17 alloy.
Microstructure Evolution and Mechanical Properties of High Nb-TiAl Intermetallic Compounds during Heat Treatment

Liangliang Li,Yongliang Zhang,Jianwei Mu,Jinlong Li,Pengfei Li,Jing Li,Zhifeng Liu

DOI: https://doi.org/10.1007/s11665-024-09301-0

IF: 2.3

2024-03-09

Journal of Materials Engineering and Performance

Abstract:High Nb-TiAl intermetallic compounds are a promising lightweight high-temperature structural material for aerospace engines due to their low density, high specific strength, creep resistance, and oxidation resistance. This study focuses on controlling the microstructure and properties of cast high Nb-TiAl intermetallic compounds with an atomic composition of 46Ti-46Al-8Nb through heat treatment. Three different heating temperatures, 950, 1200, and 1280 °C, were employed with corresponding holding times of 24, 1, and 0.5 hours, followed by furnace cooling (FC). The results indicate that heat treatment significantly influences the microstructure of the cast high Nb-TiAl intermetallic compounds, resulting in precipitated dendrite arms with lower contents of Ti and Al elements compared to the matrix region. Electron backscatter diffraction (EBSD) results reveal that all samples primarily consist of grains with large-angle grain boundaries. Notably, the 1200 °C-1 h-FC cooling treatment slightly decreases the Rockwell hardness, whereas the 1280 °C-0.5 h-FC treatment enhances the hardness. Furthermore, heat treatment significantly improves the tensile strength of the cast samples.

materials science, multidisciplinary
The Influences of Heat Treatment on the Microstructure and Mechanical Properties of Rolled Ti2AlNb

Tianze Liu,Xuewen Li,Boxin Wei

DOI: https://doi.org/10.3390/met13050886

IF: 2.695

2023-05-04

Metals

Abstract:In this study, the microstructural evolution, distribution, morphology, and change mechanism of an as-rolled Ti2AlNb alloy were quantitatively analyzed by X-ray diffraction and electron backscatter diffraction (EBSD). The results show that after solution treatment at 900 °C, the content of the O phase alloy decreased by 2%, which provided space for the nucleation of the α2 phase, the content of which increased by 2%. After aging treatment at 760 °C, large quantities of acicular O phase and α2 phase were precipitated in the B2 matrix, and the content of the α2 phase increased. As the aging temperature increased to 840 °C, the elongated α2 phases were connected to each other at a specific angle along the grain boundary, extending to the interior of the grain. The hardness reached its maximum value of 402 HV at 760 °C. This study deepened our understanding of the formation of the α2 phase in the microstructure of rolled Ti2AlNb alloy, and investigates the effect of α2 phase content on the hardness of the alloy in more depth.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Research on the Microstructural Evolution Mechanism and Impact Toughness of Ti-17 Alloy with an Initial Basket-Weave Microstructure

Ronggui Yang,Fei Zhao,Yuan Liu,Kefei Shi,Sheng Yin,Mei Fan

DOI: https://doi.org/10.1016/j.mtcomm.2022.103640

IF: 3.8

2022-01-01

Materials Today Communications

Abstract:In this work, the microstructural evolution mechanism and impact toughness of Ti-17 alloy with an initial basketweave microstructure were systematically studied. Ti-17 alloys were rolled by 0, 20%, 40% and 60% at 860 degrees C, and afterward immediately aged at 600 degrees C for 8 h. The main evolved microstructural features were the globularization of the lamellar primary alpha phase (alpha p) and the precipitation of the lamellar secondary alpha phase (alpha s). The globularization fraction of alpha p raised, while the fraction of precipitated alpha s first increased and then decreased as the thickness reduction increased from 0% to 60%. The globularization behavior of alpha p originated from the combination of the alpha p recrystallization and the cutting of the beta phase. The alpha s precipitation was affected by dislocation density in the beta phase. In the thickness reduction range of 0-40%, the microstructural evolution of the alpha phase (alpha p and alpha s) enhanced impact toughness, which was largely attributed to the higher amount of precipitated alpha s. However, at the thickness reduction of 60%, the impact toughness sharply decreased due to the high globularization fraction of alpha p and the minor precipitation of alpha s negatively affected the crack propagation inhibition.
Effects of Thermomechanical Treatment on the Evolution Pattern of the Α Phase and Mechanical Properties of Ti-17 Alloy

Ronggui Yang,Fei Zhao,Yuan Liu,Kefei Shi,Sheng Yin

DOI: https://doi.org/10.1016/j.mtcomm.2021.103041

IF: 3.8

2022-01-01

Materials Today Communications

Abstract:The effects of thermomechanical treatment (TMT) on the evolution pattern of the alpha phase and mechanical properties of Ti-17 alloy were investigated using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electronic microscopy (TEM). For the purpose, Ti-17 alloy with initial basket-weave microstructure is rolled by 40% at 860 degrees C and immeiate aging at different temperatures. The results indicated that the a phase was very sensitive to the aging temperature during the TMT process. Rolling led to globularization of primary alpha phase (alpha(p)) and destruction of Burgers orientation relationship between alpha(p) and beta phases. The subsequent immediate aging yielded further globularization and coarsening of alpha(p), precipitation and coarsening of secondary alpha phase (alpha(s)), and decreasing of the volume fraction of alpha(s). When the aging temperature was increased from 540 to 630 degrees C, these changes of the alpha phase reduced the tensile strength, and enhanced the plasticity and impact toughness. High correlation coefficients (more than 94%) implied that linear equations accurately described the effect of microstructure evolution of the a phase on mechanical properties. Immediate aging at 600 degrees C after hot rolling yielded good comprehensive mechanical properties. This revealed that the structure with suitable matching of globular and lamellar a phase could obtain the optimal combination of strength, plasticity and toughness for Ti-17 alloy.
Effect of Heat Treatment on Microstructures Evolution of Rapidly Solidified Ti-48Al-4Cr Alloy

Zhu Dongdong,Dong Duo,Zhou Zhaozhong,Ni Chengyuan,Zhang Yuanxiang,Wang Hongwei,Wei Zunjie

2016-01-01

Abstract:The effect of heat treatment on microstructure of Ti-48Al-4Cr (at%) alloy rapidly solidified at the wheel speed of 10 m/s was investigated by the single roller melt-spinning technique. The results indicate that after rapid solidification, the microstructures mainly consist of equiaxed gamma phase, and a few volume fraction of alpha(2), B2 phase particles and lamellar structures exist in the gamma phase matrix. After heat treatment at 723 degrees C/1 h, alpha(2) particles become unstable, but the lamellar structure is still stable. Annealing at 932 degrees C for 1 h, the alpha(2) plate in lamellar structures becomes unstable. The alpha(2) plate in the lamellar structures is subdivided into rod-shaped alpha(2) phase and alpha(2) particles. Annealing at 995 degrees C/1 h, lamellar structures of large volume fraction are dissolved; however, rod shaped alpha(2) phase still exists. B2 phase is precipitated at the grain boundary.
Microstructure Evolution of Directionally Solidified Ni–43Ti–7Al Alloy During Heat Treatment

Lei Zhou,Lijing Zheng,Yihui Guo,Huarui Zhang,Hu Zhang

DOI: https://doi.org/10.1007/s10853-012-6993-y

IF: 4.5

2013-01-01

Journal of Materials Science

Abstract:The microstructure change of directionally solidified Ni–43Ti–7Al alloy after heat treatment has been investigated by transmission electron microscopy and back scattered electron imagings in this paper. After solution and aging treatment, the NiTi + Ti2Ni anomalous eutectic structure nearly cannot be observed and Ti2Ni phases become spheroidized. The β′-Ni2TiAl precipitates are nearly spherical at the early stage of aging at 800 °C (0.1–1 h); however, they become aligned along 〈100〉 directions and change to cubic shape after aging for 20 h. In the course of further aging, the coarsened semi-coherent β′ precipitates occur preferentially in intercellular regions. Then the coarsened β′ precipitates begin to occur in intracellular regions with the increasing aging time and aging temperature. These β′ precipitates change the shape to sphere and plate, accompanied with loss of their coherency by introducing interface dislocations surrounding them. Finally, the formation mechanism of β′ precipitates are discussed compared to other studies in the Ni–Ti–Al system.
Microstructure Evolution Behavior of Titanium Microalloyed Steel during Heat Treatment

Jiaji Wang,Meidi Wang,Lili Li,Jin Liu,Xiaohan Jiang,Yingxue Teng,Kuijun Fu,Dazheng Zhang,Jing Guo

DOI: https://doi.org/10.1007/s11665-024-09413-7

IF: 2.3

2024-05-09

Journal of Materials Engineering and Performance

Abstract:To study the microstructure evolution behavior of titanium microalloyed steel during heat treatment, we studied the effects of different heat treatment temperatures on the microstructures and properties of titanium microalloyed steels. A high-temperature laser confocal experiment was used to observe the microstructural changes in the steel during heating, and the subsequent heat treatment temperatures were determined. Four experimental steels with different titanium contents were heat treated at 860 °C, 880 °C, 900 °C, and 920 °C. These heat treatments were combined with OM and TEM analyses of the mechanical properties and microstructural changes in the steels. The results showed that steel with a high titanium content corresponded to a high optimal heat treatment temperature, which could achieve grain refinement at high temperatures. As the heat treatment temperature increased, the strengths of all four test steels first decreased and then gradually decreased, while the ductility first increased and then decreased. The microstructures of the microalloyed steels exhibited pearlite spheroidization, carbide precipitation, carbide growth, homogenization, and matrix dissolution. When the carbide precipitated, the best mechanical properties could be obtained. This discovery could provide a microscopic theoretical mechanism for optimizing the optimal heat treatment of titanium microalloyed steel.

materials science, multidisciplinary

Microstructure coarsening behavior of Ti-17 alloy with equiaxed alpha during heat treatment

Coarsening Behavior of Lamellar Microstructure of TC17 Titanium Alloy During Heating Processing in α+β Phase Field

Microstructure evolution during isothermal forging and subsequent heat treatment of Ti-17 alloy with a lamellar colony structure

Coarsening Kinetics and Morphological Evolution in a Two-Phase Titanium Alloy During Heat Treatment

Static Coarsening Behavior of the Lamellar Alpha in Ti-17 Alloy

Microstructural Instability of A Tial-Based Alloy During Rapid Heating Cyclic Heat Treatment

Microstructural Evolution of A Forged Tial Based Alloy During Heat Treatment at Subtransus Temperature

Experimental investigation of coarsening behavior of TA15 titanium alloy in beta-phase field

Microstructure and Mechanical Properties of TC21 Titanium Alloy after Heat Treatment

Evolution of the microstructure of as-rolled Ti-43AI-9V-Y alloy with different heat treatments

Microstructure Evolution of Rapidly Solidified Ti3al-2nb Alloy

Evolutions of the Microstructures and Mechanical Properties of Ti-2.8 Wt%cu Alloy During Heat Treatment

Evolution Laws of Microstructures and Mechanical Properties During Heat Treatments for Near-Α High-Temperature Titanium Alloys

Quantitative Relationships Between Mechanical Properties and Microstructure of Ti17 Alloy after Thermomechanical Treatment

Microstructure Evolution and Mechanical Properties of High Nb-TiAl Intermetallic Compounds during Heat Treatment

The Influences of Heat Treatment on the Microstructure and Mechanical Properties of Rolled Ti2AlNb

Research on the Microstructural Evolution Mechanism and Impact Toughness of Ti-17 Alloy with an Initial Basket-Weave Microstructure

Effects of Thermomechanical Treatment on the Evolution Pattern of the Α Phase and Mechanical Properties of Ti-17 Alloy

Effect of Heat Treatment on Microstructures Evolution of Rapidly Solidified Ti-48Al-4Cr Alloy

Microstructure Evolution of Directionally Solidified Ni–43Ti–7Al Alloy During Heat Treatment

Microstructure Evolution Behavior of Titanium Microalloyed Steel during Heat Treatment