Abstract:The impact of minor Mg addition on microstructure and mechanical properties of cast Al–Li–Cu–Zr alloy with high lithium content (3 wt % Li) were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations and its effect on mechanical properties. Scanning Electron Microscope and X-ray diffraction results suggested that raising the content of Mg gradually altered the grain structure of the as-cast alloys and increased the types and volume fraction of the grain boundary intermetallic phase. Unusually, solvus temperature is higher than solidus temperature in 0.5 Mg alloy (Al–3Li–2Cu-0.5Mg-0.15Zr, wt. %), resulting in the incipient melting of the matrix before the complete dissolution of the intermetallic phases. Prominent enhancements in both age-hardening and precipitation kinetics of the base alloy with the addition of Mg were also easily identified, indicating the important role of Mg during isothermal aging. Transmission Electron Microscope and atom probe tomography results showed that minor Mg addition (0.2 wt %, denoted by 0.2 Mg alloy) could encourage the diffusion of Cu atoms by the aggregation of Mg–Cu-vacancy co-clusters, thereby promoting the nucleation of the T1-Al2CuLi and θ′-Al2Cu precipitates. In addition, S′-Al2CuMg precipitate was therefore introduced as a result of Mg addition. With further increasing the content of Mg to 0.5 wt %, the nucleation and growth of S′ precipitate would be promoted at the expense of T1 and θ′ precipitates, especially the latter. Based on the theoretical models and regression analysis, the formation mechanism of δ′-Al3Li precipitate-free-zones gradually changed from the initial vacancy-depletion mechanism to the solute-depletion mechanism, and Mg element could significantly inhibit the coarsening of δ′ precipitate-free-zones. The best balance between ductility and strength was obtained by 0.2 Mg alloy aged for 32 h, and the alloys have significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over conventional cast aluminum alloys (density: 2.7–2.8 g/cm3; elastic modulus: 72 GPa).

The Influence of Cu/Mg Atomic Ratios on Precipitation Scenarios and Mechanical Properties of Al–Cu–Mg Alloys

Influence of Mg and Cu on Precipitation Behaviors and Mechanical Properties of Al-Si Alloys

Influences of Mg content on the microstructures and mechanical properties of cast Al–2Li–2Cu–0.2Zr alloy

Effect of Cu Content and Zn/Mg Ratio on Microstructure and Mechanical Properties of Al–Zn–Mg–Cu Alloys

Effects of Cu Content and Cu/Mg Ratio on the Microstructure and Mechanical Properties of Al–Si–Cu–Mg Alloys

Investigation on microstructure and mechanical properties of Al-Zn-Mg-Cu alloys with various Zn/Mg ratios

Effects of Cu/Mg Ratio on the Microstructure, Mechanical and Corrosion Properties of Al-Li-Cu-Mg-X Alloys

Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy

Study on properties and precipitation behavior of 6000 series alloys with high Mg/Si ratios and Cu contents

Effect of Mg content on Cu precipitation behavior in Al-Cu-Mg ternary alloy by molecular dynamics simulation

Influence of Mg Doping on the Structure and Mechanical Properties of Al2Cu Precipitated Phase by First-Principles Calculations

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Insights into precipitation characteristics and strengthening mechanisms in a low Cu/Mg ratio Al-Cu-Mg-Ag alloy

Effect of Cu content on the mechanical properties of an Al–Cu–Mg–Ag alloy

Influence of Mg content on ageing precipitation behavior of Al-Cu-Li-x alloys

Effect of Zn on Precipitation Evolution and Mechanical Properties of a High Strength Cast Al-Li-Cu Alloy

New Insight into Enhancing the Comprehensive Mechanical Performance in Non-Stretched Al-Cu-Li-(Mg)-(Ag)-Mn-Zr Alloys

Influence of Mg Contents on Aging Precipitation Behavior of Al–3.5Cu–xMg Alloy

Precipitate microstructures, mechanical properties and corrosion resistance of Al-1.0 wt%Cu-2.5 wt%Li alloys with different micro-alloyed elements addition

Effect of Zn/Mg Ratios on SCC, Electrochemical Corrosion Properties and Microstructure of Al-Zn-Mg Alloy

The influence of Cu/Li ratio on precipitation in Al–Cu–Li–x alloys