Abstract:The purpose of strengthened plasters (interior applications) and renders (exterior applications) in this paper is to control cracks at the interface between the main structure and the infill wall rather than strengthen masonry and reinforced concrete structures. Cracks in plasters and renders have caused severe issues that need to be resolved urgently. Cracks affect not only the aesthetics but also the normal use of a building. The presence of cracks changes the perceptions of the owners of a structure, forcing them to question its safety and even take legal action against its developer. Consequently, the present paper discusses the effects of different strengthening materials on the tensile behaviour of plasters and renders, particularly on the first cracking. One test group without strengthening materials and six test groups with strengthening materials were tested under uniaxial tensile loads. Each experimental group included the same six specimens. A glass fibre-reinforced polymer (GFRP) grid, two types of basalt fibre-reinforced polymer (BFRP) grids, and three types of welded wire meshes (WWMs) were selected as the strengthening materials in the tests. Four types of plasters and renders were used: cement mortar, anti-crack mortar, gypsum plaster, and thermal insulation mortar. The crack pattern, stain–stress relationship, first cracking strain, energy dissipation capacity in the uncracked stage, and microstructure were investigated to gain better insight into the tensile behaviour of the plasters and renders. It was found that a strengthening material with a small mesh size resulted in numerous cracks and a narrow crack spacing. The stress–strain curves of the strengthened specimens could be divided into uncracked and cracked stages. The higher slopes in both stages of the strengthened specimens could be attributed to the higher longitudinal strain coefficient, smaller opening size, and larger cross-sectional area of each strand of the strengthening materials. The first cracking strain of the unreinforced specimen was smaller than that of a strengthened specimen. Stronger bond strength between plaster/render and strengthening material, smaller mesh size and greater cross-sectional area of each strand of strengthening material led to the larger first cracking strain. The energy dissipation capacity in the uncracked stage of the strengthened thermal insulation mortar was the least. The energy dissipation capabilities in the uncracked stage of the plasters/renders reinforced with BFRP grid-2 and WWM-3 were the second-highest and highest, respectively. The bond strengths of the GFRP and BFRP grids to the plasters/renders were stronger than those of the WWMs. The bond strengths between the gypsum plaster and the reinforcing materials were the highest, whereas those between the thermal insulation mortar and the strengthening materials were the lowest. Additionally, stress–strain relationships were proposed for the strengthened plasters and renders; the results were found to be in good agreement with the test results.

Field Testing the Strength of Thin-Layer Mortars Using the Pull-Out Method

Experimental Study on Mechanical Properties of Basalt Fiber-Clay Lime Mortar and Application in Brick Masonry

Experimental research on the strength of concrete mearsured by limpet

Effect of Different Strengthening Materials on Tensile Behaviour of Plasters and Renders

A Study on the Relationship Between the Performance of External Thermal Insulating Anti-Crack Mortar and Maintenance Time

Experimental Research on Concrete Strength Prediction by Limpet Pull-off Test in China

The Mechanical Properties of Polymer-cement Mortar

Experimental Study on Mechanical Properties of Low-Strength Mortar–Granite Composite Specimens

Bond Performance of Hook-End Steel Fiber to the Mortars Cured for 360 Days

Large scale experimental study on bond behavior between polymer modified cement mortar layer and concrete

STUDY ON GLUING-PULLING METHOD FOR CONCRETE STRENGTH TEST

Experimental pull-out tests and design indications for strength anchors installed in masonry walls

Experimental study on axial compressive behavior of stone masonry with ultra-high performance mortar

Experimental Study on Low Strength Brick Masonry Wall Strengthened with Self-compacting Concrete Wall

Investigation on Hydration and Mechanical Properties of Mortar Containing Limestone Powder and Fly Ash Based on the Coupled Chemical–Thermal–Mechanical Method

Physical and 3D numerical modelling of reinforcements pullout test

Comparison of Influence of Superficial Strengthening with FRCM System and Kind of Mortar Type on Shear Strength of Autoclaved Aerated Concrete Masonry

EXPERIMENTAL STUDY ON PHYSICAL AND MECHANICAL PROPERTIES OF STICKY RICE-LIME MORTAR

Dynamic compressive and splitting tensile tests on mortar using split Hopkinson pressure bar technique

A Study on the Mechanical and Wear-Resistance Properties of Hybrid Fiber Mortar Composites with Low Water-Cement Ratios

Analysis on the Strength of Cement Mortar Mixed with Construction Waste Brick Powder