Abstract:The acidic (pKa ≈1.5–2.5) and hygroscopic nature of poly(3,4-ethylene dioxythiophene) polystyrene sulfonate, used as a common hole-injection layer in optoelectronic devices, has a detrimental effect on device stability and is associated with well established device failure mechanisms. In this work, a process with a high green index hole-injection layer material (V2O5) and low surface roughness (RMS roughness ≈1.3 nm) was developed for demonstrating a hybrid polymer–inorganic perovskite light-emitting diode. Test devices with the new hole-injection layer demonstrate nearly identical maximum current efficiencies (4.23 vs 4.19 cd/A), and luminous efficacies (2.99 vs 2.32 lm/W) when compared to a control device fabricated with the conventional hole-injection layer. Furthermore, the peak brightness was achieved at a current density one-third of the value for the control device. To examine the transport of holes in the above hole-injection layer, we carried out device simulations based on a physical charge control model, including defect-assisted tunneling for hole injection. Close agreement for current–voltage characteristics is observed. Experimentally measured mobility in the device and measured radiative lifetimes were found to be sufficient to achieve this agreement without resorting to the introduction of a sheet charge at the injection interface. Despite the use of a bulk-heterojunction device architecture, the model predicts high radiative recombination rates [≈5.6×1022/(cm3s)] in the emissive layer, consistent with the measured photophysical properties for the active film, suggesting effective passivation of non-radiative surface states.

Hole-Injection Enhancement by Copper Phthalocyanine (cupc) in Blue Polymer Light-Emitting Diodes

Conjugated Polyelectrolytes as Efficient Hole Transport Layers in Perovskite Light-Emitting Diodes.

Polarized Blue Polymer Light-Emitting Diodes Utilizing Rubbed Hole Injection Layers

PCDTBT: from Polymer Photovoltaics to Light-Emitting Diodes by Side-Chain-Controlled Luminescence

Low Operating-Voltage and High Power-Efficiency OLED Employing MoO3-doped CuPc As Hole Injection Layer

Enhancing hole injection by electric dipoles for efficient blue InP QLEDs

Defect-assisted hole transport through transition metal oxide-based injection layers for passivated nanocrystalline CsPbBr3 emissive thin films: A combined experimental and modeling study

Efficient Blue PhOLEDs Using Host Materials of Lower Triplet Energy Than the Emitter

Blue Electroluminescent Devices Using the Dye-Doped Polymers As Emitter and the Organic-Molecule Film As Hole Blocking Layer

Polymeric Hole Transport Materials for Red CsPbI3 Perovskite Quantum-Dot Light-Emitting Diodes

Blue polymer light-emitting diodes with organic/inorganic hybrid composite as hole transporting layer

Mechanism of improving the performance of organic electroluminescent divices by using CuPc as buffer layer

An Efficient Blue Organic Light Emitting Structure

Superior Hole Injection Material PEGDT/TPF/PVDF with p-Doping Capability for Highly Efficient Solution-Processed Organic Light-Emitting Diode

Influence of Hole Buffer Layer CuPc on Properties of Organic Light-Emitting Devices

Effect of adjusting charge transport on optoelectronic performances of polymer light-emitting diodes based on SY-PPV

Poly(pyridine-2,5-diyl) as electron-transport/hole blocking layer in poly(phenylene vinylene) light-emitting diode

Improved Electroluminescence Performance of Perovskite Light-Emitting Diodes by a New Hole Transporting Polymer Based on the Benzocarbazole Moiety

Improved hole injection for CsPbI 3 nanocrystals based light-emitting diodes via coevaporation of hole transport layer

Design of Hole Blocking Layer with Electron Transport Channels for High Performance Polymer Light‐Emitting Diodes

Enhancing Blue Polymer Light-Emitting Diode Performance by Optimizing the Layer Thickness and the Insertion of a Hole-Transporting Layer