Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Optimizing Heat Transfer Rate in an Internally Cooled Cutting Tool: FE- Based Design Analysis and Experimental Study

Research on 3D Numerical Simulation and Experiment of Cutting Temperature for High Speed Milling of Aerospace Aluminum Alloy

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

Modeling and Monitoring of the Tool Temperature During Continuous and Interrupted Turning with Cutting Fluid

On modelling coolant penetration into the microchannels at the tool-workpiece interface

Internally cooled tools as an innovative solution for sustainable machining: Temperature investigation using Inconel 718 superalloy

Internal cooling system effects to heat transfer and tool wear in turning operations of titanium alloys Ti6Al4V

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

Comparison of the performance of the internally cooled tool in closed circuit against standard PCBN tools in turning AISI D6 hardened

Study on magnetohydrodynamic internal cooling mechanism within an aluminium oxide cutting tool

Numerical Analysis of Microchannels Designed for Heat Sinks

Design of machine tool cooling system and optimization of cooling parameters based on differential cooling control strategy

Investigation of heat partition and instantaneous temperature in milling of Ti-6Al-4V alloy

Topology optimization in cooling moving heat sources for enhanced precision of machine tool feed drive systems

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions

A new internal cooling system for a green tubular channel investigated for tool life in Hastelloy-B3 turning for MQL medium

Temperature Experiment and Parameter Optimization of Cemented Carbide Tool in Milling 508III Steel

Design and fabrication of an aluminium oxide cutting insert with an internal cooling channel

Experimental and computational analysis of the coolant distribution considering the viscosity of the cutting fluid during machining with helical deep hole drills

The heat partition into cutting tool at tool-chip contact interface during cutting process: a review

Thermal Structure Design and Analysis of A Machine Tool Headstock