Abstract:The mechanical anisotropic properties of aluminum alloy are studied using multi-level approaches for strain-rate and temperature-sensitive large plastic deformation of polycrystalline aggregates. Unlike previous researches, the thermal effect and the damage evolution process are considered simultaneously and integrated in the CPFEM method. In the microscopic constitutive equation of crystal plasticity, the shear strain rate on the slip system is described by an advanced exponential function based on thermal activated mechanism, instead of traditional phenomenological power-law function. To determine the rate-sensitive material parameters in this new model, the strain rate and temperature jump tests are performed. In addition, a simulation of one representative volume element is compared to the results of conventional tensile tests to obtain other thermal parameters. Coupled with the continuum damage evolution formula, this thermal affected crystal plasticity model is then implemented in a single crystal analysis for different orientation, temperature and strain rate conditions. Finally, this extended crystal plasticity model is applied in the finite element method to simulate the mechanical properties of 5052 aluminum alloy at absolute temperature 473 K. Taylor model is also used to compare these simulations as well as the experimental data. The results show that the damage model coupled in the crystal plasticity is able to predict the mechanical response of 5052 aluminum alloy; moreover, this model can simulate the explicit evolution of damage factor and local stress concentration in the deformation of standard tensile test specimen. In the simulation, the specimen is meshed by rectangular elements and each element is given an initial orientation at the first time increment step. This study argues that even in high temperature, the orientation mismatch between adjacent grains could lead to early cavity or crack initiation and the damage development is similar to the void evolution theory. An explanation of the possible fracture angle is given in the thermal tensile test due to polycrystalline anisotropy. At last, the analysis of stress heterogeneity and texture evolution is also shown in this study.

Polycrystalline Model Predictions of Flow Stress and Textural Hardening during Monotonic Deformation

Effect of Hardening Models on the Prediction of Deformation Textures for Polycrystalline

Investigation on Plastic Flow Behaviors of FCC Polycrystalline Aluminum under Pre-Cyclic Tension-Compression Loading: Experiments and Crystal Plasticity Modeling.

Effects of the Isotropic and Anisotropic Hardening Within Each Grain on the Evolution of the Flow Stress, the R-Value and the Deformation Texture of Tensile Tests for AA6016 Sheets

Crystal Plasticity Modeling of Texture Evolution and Heterogeneity in Equal Channel Angular Pressing of Aluminum Single Crystal

Article I. Statistical Models for Deformation Texture Prediction Using Vortex-Type Accommodation of Local Strain Misfits

Validation of the Texture-Based ALAMEL and VPSC Models by Measured Anisotropy of Plastic Yielding

Polycrystalline Model for FE-simulation of Micro Forming Processes

A finite strain micromechanical-based constitutive model: Application to porous polycrystal

Modeling Texture Development During Cold Rolling of IF Steel by Crystal Plasticity Finite Element Method

Accurate Simulation of Texture Evolution and Mechanical Response of Cubic and Hexagonal Structural Alloys Using Self-Consistent Polycrystal Plastic Method

Numerical Simulation on Sheet Metal Forming with Rate-Independent Polycrystalline Plasticity Fem

Anisotropic Sheet Forming Simulations Based on the Alamel Model: Application on Cup Deep Drawing and Ironing

Constitutive analysis of hot deformation behavior of a Ti6Al4V alloy using physical based model

Characterisation and modelling of anisotropic hardening behaviour of cubic and hexagonal close packed polycrystalline metals

A Damage-Effect-involved Phenomenological Crystal Plasticity Model and Computational Methods for Mechanical Responses of FeCrAl Alloys

Mechanical Behavior and Texture Evolution of Aluminum Alloys Subjected to Strain Path Changes: Experiments and Modeling

Evaluation of Anisotropic Constitutive Models: Mixed Anisotropic Hardening and Non-Associated Flow Rule Approach

A dual-scale elasto-viscoplastic constitutive model of metallic materials to describe thermo-mechanically coupled monotonic and cyclic deformations

Crystal Plasticity-Based Assessment of Constitutive Laws for Microstructure and Rolling Texture Capture in Ferritic Stainless Steel During Cold Rolling

Crystal plasticity extended models based on thermal mechanism and damage functions: Application to multiscale modeling of aluminum alloy tensile behavior