Abstract:Electron beam selective melting (EBSM), is powder bed fusion additive manufacturing (AM) technique by adding materials layer upon layer. The capacity of EBSM to fabricate complex and multi-functional parts has made it a realm of great interest for researchers in the domain of science. However, during the fabrication of functionally graded materials (FGMs) with graded composition by EBSM using at least two different materials, it is difficult to separate and reuse these materials after the fabrication. Additionally, it is difficult to vary the powder composition within a layer to fabricate a horizontal graded structure. In this research, an element evaporation concept based on electron beam powder bed fusion, is presented for fabricating one-dimensional (1D) FGMs of (α2 + γ) TiAl alloy/(α + β) titanium alloy from a single material powder. By irradiating different sub-regions of the powder bed with electron beam energy input of different magnitude to greatly reduce the relative atomic ratio of aluminum from 47% to less than 10%, the 1D FGMs structures with (α2 + α + β) phases in the interfacial transition zone (ITZ) were successfully produced. Since the microstructure of the ITZ has a significant effect on mechanical properties for the 1D FGMs, three different overlap scan distances (0.5, 1.0 and 2.0 mm), which result in different ITZs, were utilized for evaluating the microstructure of the ITZ and resulting mechanical properties. The results showed that no defects were found in the specimens of any overlap distance. Moreover, the width of the ITZ increases as the overlap scan distance, and the tensile strength decreases with the overlap scan distance.

Characterization of W/Fe Functionally Graded Materials Manufactured by Resistance Sintering under Ultra-High Pressure

Fabrication and microstructure of W/Cu functionally graded material

Fabrication of W–Cu Functionally Graded Material with Improved Mechanical Strength

Fast fabrication of W-Cu functionally graded material by high-gravity combustion synthesis and melt-infiltration

Simulation and Study of Manufacturing of W–Cu Functionally Graded Materials by a Selective Laser Melting Process

Synthesis of Functionally Graded AA7075-B4C Composite with Multi-Level Gradient Structure

Preparation of W–V Functionally Gradient Material by Spark Plasma Sintering

Preparation of W-Cu functionally graded material coated with CVD-W for plasma-facing components

Experimental and Numerical Studies on W–Cu Functionally Graded Materials Produced by Explosive Compaction–welding Sintering

Fabrication of W-Cu functionally graded material by spark plasma sintering method

Microstructure and Properties of Wcp/Cu Layered Functionally Graded Materials Prepared by Vacuum Hot-Pressed Sintering

A Novel Preparation Approach of Aluminum-Based Functionally Graded Material: Auxiliary Wire Filling Gas Metal Arc Directed Energy Deposition

Fabrication of Al2O3/TiC/Ni Functionally Graded Materials by Pulsed-Electric Current Sintering and Their Mechanical Properties.

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Development and Characterization of 316l/inconel625 Functionally Graded Material Fabricated by Laser Direct Metal Deposition

Effect of the Post-Production Heat Treatment on Phase Evolution in the Fe3Ni–FeNi Functionally Graded Material: an In-Situ Neutron Diffraction Study

Investigation on 316L/316L-50W/W plate functionally graded materials fabricated by spark plasma sintering

Fabrication and Application of W/Cu Functionally Graded Material

Structure and Property of W-Ni-Cu Functionally Graded Materials by Composite Electrodeposition

Characterization of Interfacial Transition Zone of Functionally Graded Materials with Graded Composition from a Single Material in Electron Beam Powder Bed Fusion

A functionally graded material from stainless steel 304 to Fe–40Al fabricated by dual wire arc additive manufacturing