Abstract:A cellular automaton (CA)-finite element (FE) model was implemented for multi-scale modelling of micro-segregation, mesoscopic grain structure and macroscopic segregation during direct chill (DC) casting of industrial billets or slabs. The macroscopic transport of mass, momentum, energy and solutes was solved on an FE grid, while the mesoscopic grain structure governed by nucleation, growth kinetics and grain evolution was calculated on a CA grid. The solidification path was determined using a modified micro-segregation model for multi-component aluminium alloys. An Euler representation was used for pre-processing and post-processing, and a Lagrangian representation was used for expanding the calculation domain and for resolving the CAFE model. By simulating a DC casting experiment of the 2024 aluminium alloy, a typical grain structure was reproduced, and the composition map showed a reasonable deviation. This model was applied to an industrial-scale DC cast slab of an Al-3.5Cu-1.5 Mg (wt. %) alloy, and three simulations with different nucleation undercoolings were performed for a grain-unrefined slab, a grain-refined slab and an equilibrium solidified slab, respectively. The slabs tended to solidify at equilibrium with the decreasing nucleation undercooling. The earlier release of latent heat yielded a smaller liquid undercooling region ahead of the solidification front, and a finer grain structure. A typical grain structure with coarse equiaxial grains at the centre and fine columnar grains near the bottom surface as well as sidewall was observed for the grain-unrefined slab. By contrast, the grain structure of the grain-refined slab was fully equiaxial. Furthermore, the grain structure, temperature field, melt flow and macro-segregation were quantitatively investigated.

Simulation of Stray Grain Formation During Unidirectional Solidification of In738lc Superalloy

Simulation of stray grain formation at the platform during Ni-base single crystal superalloy DD403 casting

Numerical Simulation of Grain Selection Behavior of Single Crystal Ni3al Based Superalloy Casting

Numerical Simulation of Temperature Field and Grain Texture During Casting Single Crystal Superalloy DD403 with Liquid Metal Cooling

Numerical Simulation of Temperature Field and Grain Structure in the Solidification of K4169 Superalloy Shell Casting

Numerical Simulation of Solidification Structures of Ag-28Cu Alloy Continuous Casting Based on 3D-CAFE Method

Simulation of microstructures in solidification of aluminum twin-roll casting based on CA

Modelling of Solidification Structure and Macro-Segregation in an Industrial DC Cast Slab

Transient Modeling Of Grain Structure And Macrosegregation During Direct Chill Casting Of Al-Cu Alloy

Numerical Simulation of Solidification Structure of Al Alloy During Centrifugal Casting

Stray Grain Formation in Casting Platform of Third Generation Ni-Base Single Crystal Superalloy

Numerical Simulation of Solidification Structures Influenced by Cooling Spraying and Process Parameters Based on Cellular Automaton Finite-Element Model

Formation of Stray Grains During Directional Solidification of a Superalloy AM3

Numerical Simulation of Temperature Field and Grain Structure in Cu-10Al Alloy Produced by Heated Mould Continuous Casting

Simulation of Solidification Microstructure of Fe-6.5%Si Alloy Using Cellular Automaton-Finite Element Method

Three Dimensional Numerical Simulation of Solidification Microstructure of Single Phase Alloy

Simulation of the as-cast structure of Al-4.0wt.%Cu ingots with a 5-phase mixed columnar-equiaxed solidification model

Computer Simulation of Equiaxed Microstructure Formation in Solidification of Al-4%Cu Alloy

Numerical Modeling of Grain Refinement During Solidification of Mg-4Y-3Nd (wt.%) Alloy Via Mesh-Anisotropy Reduction Algorithm

Simulation of Fine Grain Casting Process of Superalloy K4202 by Thermal Control Method

Modelling freckles and spurious grain formation in directionally solidified superalloy castings