Inhalable Nano-Dimpled Microspheres Containing Budesonide-PLGA for Improved Aerodynamic Performance
DOI: https://doi.org/10.2147/IJN.S372582
IF: 7.033
2022-08-03
International Journal of Nanomedicine
Abstract:Chang-Soo Han, 1, &ast Ji-Hyun Kang, 1, &ast Young-Jin Kim, 1 Dong-Wook Kim, 2 Chun-Woong Park 1 1 College of Pharmacy, Chungbuk National University, Cheongju, 28160, Republic of Korea; 2 College of Pharmacy, Wonkwang University, Iksan, 54538, Republic of Korea &astThese authors contributed equally to this work Correspondence: Chun-Woong Park, College of Pharmacy, Chungbuk National University, 194-21, Osongsangmyeong 1-ro, Heungdeok-gu, Cheongju, Chungbuk, 28160, Republic of Korea, Tel +82-43-261-3330, Fax +82-43-268-2732, Email Introduction: Dry powder inhalations are an attractive pharmaceutical dosage form. They are environmentally friendly, portable, and physicochemical stable compared to other inhalation forms like pressurized metered-dose inhalers and nebulizers. Sufficient drug deposition of DPIs into the deep lung is required to enhance the therapeutic activity. Nanoscale surface roughness in microparticles could improve aerosolization and aerodynamic performance. This study aimed to prepare microspheres with nanoscale dimples and confirm the effect of roughness on inhalation efficiency. Methods: The dimpled-surface on microspheres (MSs) was achieved by oil in water (O/W) emulsion-solvent evaporation by controlling the stirring rate. The physicochemical properties of MSs were characterized. Also, in vitro aerodynamic performance of MSs was evaluated by particle image velocimetry and computational fluid dynamics. Results: The particle image velocimetry results showed that dimpled-surface MSs had better aerosolization, about 20% decreased X-axial velocity, and a variable angle, which could improve the aerodynamic performance. Furthermore, it was confirmed that the dimpled surface of MSs could cause movement away from the bronchial surface, which helps the MSs travel into the deep lung using computational fluid dynamics. Conclusion: The dimpled-surface MSs showed a higher fine particle fraction value compared to smooth-surface MSs in the Andersen Cascade Impactor, and surface roughness like dimples on microspheres could improve aerosolization and lung deposition. Keywords: nanoscale dimple, aerodynamic performance, particle image velocimetry, computational fluid dynamics Dry powder inhalers (DPIs) are attracting attention as treatments for lung diseases. DPIs have propellant-free, portable, and stable physicochemical properties and offer environmental and economic advantages. Successful therapy using DPIs depends upon the formulation, the aerosol device, and the patient. 1,2 This study investigated the effect of aerodynamic behavior on the dimpled nanostructure of microspheres. Microparticle roughness has been reported to have either a positive or a negative effect on pulmonary delivery. The negative effects of increased roughness were increased drug adhesion and particle-particle interaction in micro-level roughness. 3 In contrast, a positive effect was the reduction of particle-particle interactions due to nano-level roughness. 4–6 Furthermore, differences in surface roughness can also affect powder behavior in terms of particle velocity and the diversity of directions as it exits the device and moves within the lungs. 7,8 The dimpled structure and increased roughness of a golf ball allow for a four-times greater travel distance than does a smooth ball because of its reduced drag and lift. This causes the air to move faster at the top of the ball, creating a lower pressure there. 9,10 A dimpled nanostructure in microspheres can provide better aerodynamic behavior, similar to that of a golf ball. Increased roughness that does not have interlocking structures can show an improved aerodynamic performance owing to reduced particle-particle interactions and the behavior of the particles coming from the device and into the lungs. 11–14 Dimpled microspheres have been prepared by a spray dryer, droplet imprinting, and the emulsion method. 15–17 The oil in water (O/W) solvent evaporation method is the simplest approach and obtains a high yield with a narrow particle size distribution. 18–20 Dimpled- surface and smooth-surface microspheres, consisting of budesonide (BUD) and poly (D, L lactic-co-glycolic acid) (PLGA) were made using the O/W solvent evaporation method. 21 We controlled for the shear rate in the solvent evaporation steps. They had similar sizes, distribution, and physicochemical properties, but different surface morphology. 22 Particle image velocimetry (PIV) is a technique for capturing flow fields in fractions of a second. Particle characteristics such as velocity and direction can be quantified and -Abstract Truncated-
pharmacology & pharmacy,nanoscience & nanotechnology