A method for solving Laplace's equation with mixed boundary condition in electromagnetic flowmeters

Zhang Xiao Zhang

DOI: https://doi.org/10.1088/0022-3727/22/5/001

1989-01-01

Abstract:A method is presented to solve mixed boundary value problems of Laplace's equation. Several important examples in electromagnetic flowmeters are given.

What problem does this paper attempt to address?

Divisionally Analytical Solutions of Laplace'S Equations for Dry Calibration of Electromagnetic Velocity Probes

L. Hu,J. Zou,X. Fu,H. Y. Yang,X. D. Ruan,C. Y. Wang

DOI: https://doi.org/10.1016/j.apm.2008.10.016

IF: 5.336

2009-01-01

Applied Mathematical Modelling

Abstract:The potentials of weight function W→ and magnetic flux density B→ both obey Laplace’s equations in the measuring volume around an electromagnetic velocity probe. Analytical solutions of the Laplace’s equations are pre-requisite for the dry calibration of the probe, in which the sensitivity of the probe is calculated according to a mathematical model. However, the complexity of calculation geometry hindered the directly analytical solution of the equations, and there are still no effective analytical solutions applicable for the dry calibration at present. A method proposed in the paper is dividing the complex calculation geometry into two simple ones by an auxiliary surface, and thus the Laplace’s equations can be analytically solved in the each generated geometry separately. Specifically, two ways of division which can be effectively applied in the dry calibration, and the corresponding analytical solutions of the Laplace’s equations accessed using the method of separation of variables, are represented. Approaches to determine the additionally required boundary conditions on the auxiliary surfaces in dry calibration are also introduced. Finally, the study is validated on a numerical electromagnetic velocity probe.
Study of No-liquid Calibration Technique for the Medium-and-large Diameter Electromagnetic Flowmeter

Si-meng TANG,Liang HU,Jun MA

DOI: https://doi.org/10.3969/j.issn.1000-1158.2013.04.09

2013-01-01

Abstract:A no-liquid calibration technique for electromagnetic flowmeter (EMF) is presented. The proposed method utilizes the electromagnetic measuring principle. Several differential equations for the relevant physical quantities and corresponding boundary conditions are established. A set of no-liquid calibration equipment is designed and implemented. By measuring the point-by-point magnetic induction on the boundary surface as well as the structure dimensions of EMF, the sensitivity of EMF are acquired via the numerical solution of the differential equations with measured boundary conditions. The comparison of the no-liquid and practical-flow calibration methods is carried out on two EMFs with diameter of 200 mm. The relative error of the sensitivity data determined by the two methods is less than 0.5%.
Introducing a General Analytical Method for Solving Electromagnetic Fields with Complicated Boundary

QS MA,G GUO,JN SHENG,KX JIANG

DOI: https://doi.org/10.1109/20.312548

IF: 1.848

1994-01-01

IEEE Transactions on Magnetics

Abstract:In this paper, an analytical method, which may be applied to solve the Laplace's or Poission's equation, is introduced. The analytical method has been used to solve some 2-D electrostatic field problems. The calculated results have been compared with that obtained by the separation of variables or by BEM, which is expressed by the direct integral equation, respectively. Compared results show that the analytical method introduced has a lot of merits.
An Application of the Adomian's Decomposition Method to the Analysis of MHD Duct Flows

JM Machado,SLL Verardi,SY Yang

DOI: https://doi.org/10.1109/tmag.2005.845031

IF: 1.848

2005-01-01

IEEE Transactions on Magnetics

Abstract:A new approach is proposed in this work for the treatment of boundary value problems through the Adomian's decomposition method. Although frequently claimed as accurate and having fast convergence rates, the original formulation of Adomian's method does not allow the treatment of homogeneous boundary conditions along closed boundaries. The technique here presented overcomes this difficulty, and is applied to the analysis of magnetohydrodynamic duct flows. Results are in good agreement with finite element method calculations and analytical solutions for square ducts. Therefore, new possibilities appear for the application of Adomian's method in electromagnetics.
Reconstruction of the magnetic field in the measuring volume of an electromagnetic flow sensor

Liang Hu,Jun Zou,Xin Fu,Xiaodong Ruan,ChiYu Wang

DOI: https://doi.org/10.1109/AIM.2009.5230012

2009-01-01

Abstract:A novel approach to obtain the magnetic field in the measuring volume of an electromagnetic flow sensor is introduced. It is a measurement-calculation coupled approach. Utilizing a characteristic that there is no exciting current in the measuring volume, the problem is simplified to solving a Laplace's equation of magnetic scalar potential in the volume. Through measuring the distribution of normal magnetic flux density on the boundary surface of the volume using a magnetic scanning device, the necessary boundary condition to solve the Laplace's equation is provided. Finally, the magnetic field is reconstructed through solving the Laplace's equation with the measured boundary condition. This approach is more efficient and accurate than existing approaches and do not need to know the inner structure of the magnetic exciting unit. Experimental validations on a conventional pipe flow measuring sensor and a late-model local velocity measuring sensor are both given. This reconstruction approach will be very useful in the studies of not only electromagnetic flow sensors but also many other mechatronics systems such as motors, bearing and maglev etc.
Alternating Iteration Method for Solving the Laplace Equation

张小章

DOI: https://doi.org/10.3321/j.issn:1000-0054.2002.12.006

2002-01-01

Abstract:A simple, fast semianalytical method is introduced for solving boundary value problems in volving the Laplace equation. This method used parts of the boundary condition alternatively to obtain the final solution satisfying the real boundary condition. This method results in a series form of the solution that is easy to compute. The method was used to solve several engineering examples with boundary conditions of the first and the second kinds and various domains including circles, circles with several holes, and cylinders with a spherical cutout. These examples, required a maximum of 21 terms and 10 cycles of the boundary conditions to get accurate results. The results show that the method is a practical way to solve Laplace boundary value problems. 
Simulation of Electromagnetic Fields on Flow Boundary Layer Control

ZHANG Hui,FAN Bao-chun,CHEN Yao-hui,ZHOU Ben-mou,LI Hong-zhi

DOI: https://doi.org/10.3969/j.issn.1005-9830.2008.01.006

2008-01-01

Abstract:It is possible to control the flow in the electrolyte solution by Lorentz forces generated by the suitably chosen magnetic and electric fields.Based on electromagnetic equations,the electromagnetic fields induced by a cylindrical actuator in a low-conducting moving electrolyte,the voltage,the magnetic,the intensity of electric field,the intensity of magnetic field and the Lorentz forces are investigated numerically with finite differential algorithm.The distributions are analyzed.The result shows the distribution of the voltage,the magnetic,the intensity of electric field,the intensity of magnetic field and the Lorentz force are periodic in spanwise direction,and are exponential attenuation in normal direction.The wider the actuator is,the slower the attenuation is,and the deeper the effective depth is,the weaker the fluctuation of the Lorentz forces is.
Three-dimensional MHD simulations of the electromagnetic flowmeter for laminar and turbulent flows

Bo Lü,Liangwang Xu,Xiaozhang Zhang

DOI: https://doi.org/10.1016/j.flowmeasinst.2013.07.015

IF: 2.42

2013-01-01

Flow Measurement and Instrumentation

Abstract:The interaction between an electrically conducting fluid and an external magnetic field in an ideal cylindrical electromagnetic flowmeter is numerically investigated for both laminar and turbulent flows. Induced electric potential in the fluid, and the difference in potential at the measuring electrodes are directly obtained by including MHD effects in the CFD simulations. Fully developed laminar and turbulent flows are simulated. The computed electric potential difference on the electrodes agrees with analytical values for small Hartmann number cases, where the induced Lorentz force is small. Turbulent flow produces a more uniform electric potential distribution in the flow meter cross-section than laminar flow. These integrated MHD/CFD simulations couple the MHD effect with flow dynamics without deriving a weighting function with an assumed velocity profile, which will be necessary for electromagnetic flow meters when the Hartmann number is not small.
A Rectangular Mixed Finite Element Method with A Continuous Flux for an Elliptic Equation Modelling Darcy Flow

Xindong Li,Hongxing Rui

DOI: https://doi.org/10.1155/2013/580461

2013-01-01

Abstract and Applied Analysis

Abstract:We introduce a mixed finite element method for an elliptic equation modelling Darcy flow in porous media. We use a staggered mesh where the two components of the velocity and the pressure are defined on three different sets of grid nodes. In the present mixed finite element, the approximate velocity is continuous and the conservation law still holds locally. The LBB consistent condition is established, while the error estimates are obtained for both the velocity and the pressure. Numerical examples are presented to confirm the theoretical analysis.
Hybrid Laplace transform finite element method for solving the convection–dispersion problem

Li Ren,Renduo Zhang

DOI: https://doi.org/10.1016/S0309-1708(99)00013-5

IF: 5.361

1999-01-01

Advances in Water Resources

Abstract:It can be very time consuming to use the conventional numerical methods, such as the finite element method, to solve convection–dispersion equations, especially for solutions of large-scale, long-term solute transport in porous media. In addition, the conventional methods are subject to artificial diffusion and oscillation when used to solve convection-dominant solute transport problems. In this paper, a hybrid method of Laplace transform and finite element method is developed to solve one- and two-dimensional convection–dispersion equations. The method is semi-analytical in time through Laplace transform. Then the transformed partial differential equations are solved numerically in the Laplace domain using the finite element method. Finally the nodal concentration values are obtained through a numerical inversion of the finite element solution, using a highly accurate inversion algorithm. The proposed method eliminates time steps in the computation and allows using relatively large grid sizes, which increases computation efficiency dramatically. Numerical results of several examples show that the hybrid method is of high efficiency and accuracy, and capable of eliminating numerical diffusion and oscillation effectively.
A Hybrid Phase Flow Method for Solving the Liouville Equation in a Bounded Domain

Hao Wu,Xu Yang

DOI: https://doi.org/10.1137/090773726

IF: 3.039

2011-01-01

SIAM Journal on Numerical Analysis

Abstract:The phase flow method, originally introduced in [L. X. Ying and E. J. Candes, J. Comput. Phys., 220 (2006), pp. 184-215], can efficiently solve autonomous ordinary differential equations. In [S. Jin, H. Wu, and Z. Y. Huang, SIAM J. Sci. Comput., 31 (2008), pp. 13031321], the method was generalized to solve Hamiltonian system where the Hamiltonian function was discontinuous. However, both of these methods require a phase flow map constructed on an invariant manifold. This can increase computational cost when the invariant domain is big or unbounded. Following the idea of [S. Jin, H. Wu, and Z. Y. Huang, SIAM J. Sci. Comput., 31 (2008), pp. 1303-1321], we propose a hybrid phase flow method for solving the Liouville equation in a bounded domain, which is smaller than the invariant manifold of a phase flow map. By using some proper boundary conditions, this method can help solve the problem where the invariant manifold of a phase flow map determined by the Liouville equation is unbounded. We verify numerical accuracy and efficiency by several examples of the semiclassical limit of the Schrodinger equation. Analysis of numerical stability and convergence is given for the semiclassical limit equation with inflow boundary condition.
Numerical Simulation for Magnetostatic Problems Based on A-λ Mixed Finite Element Method

Jiang Peng,Li Jing,Zhang Qun,Luo Linshan,Guan Zhenqun

DOI: https://doi.org/10.19595/j.cnki.1000-6753.tces.162025

2018-01-01

Abstract:This paper proposes to adopt mixed finite element method to eliminate spurious solution in simulating magnetostatic problems. By introducing a scalar Lagrange multiplier, Coulomb gauge is incorporated into magnetic vector potential formulation based on constrained variational principle, leading to A-λ mixed formulation. Furthermore, the gradient of the scalar Lagrange multiplier is identified as the incompatible component of exciting current source. By means of Newton-Raphson method, iterative strategy is established for material nonlinearity problems. Edge elements are employed to discretize magnetic vector potential, and nodal elements are employed to discretize Lagrange multiplier. By augmented Lagrange multiplier technique, the saddle point problem arising from mixed finite element discretization can be transferred to an equivalent problem which can be iteratively solved by Uzawa method. Compared with conventional nodal element and edge element, the mixed element can suppress potential spurious solutions, and obtain a more accurate solution.
Unified Lattice Boltzmann Method for Electric Field–Space Charge Coupled Problems in Complex Geometries and Its Applications to Annular Electroconvection

Kang Luo,Hong-Liang Yi,He-Ping Tan,Jian Wu

DOI: https://doi.org/10.1109/tia.2017.2691761

IF: 4.079

2017-01-01

IEEE Transactions on Industry Applications

Abstract:A lattice Boltzmann method (LBM) is developed to solve the electric field–space charge coupled problems. Instead of solving the macroscopic charge conservation equation and the Poisson's equation for electric potential, two discrete lattice Boltzmann equations are formulated and solved. A nonequilibrium extrapolation scheme is used to treat the boundary conditions with complex geometry. Our method is validated with several test cases for which analytical solutions and/or reference numerical results exit. An attractive feature of this methodology lies in its natural coupling with the LBM for the fluid flow. As a demonstration and also an application, the unipolar injection induced electroconvection of dielectric liquids in annular geometries is considered. The different flow patterns of the concentric and eccentric configurations are highlighted.
A Kind of Boundary Element Methods for Boundary Value Problem of Helmholtz Equation

ZHANG Ran,JIANG Zheng-yi

DOI: https://doi.org/10.3969/j.issn.1674-5647.2004.03.001

2004-01-01

Abstract:1. Problems for electromagnetic scattering are of significant importance in many areas of technology. In this paper we discuss the scattering problem of electromagnetic wave incident by using boundary element method associated with splines.
A Finite Element Method for a Unidimensional Single-Phase Nonlinear Free Boundary Problem in Groundwater Flow

D Liang,B Zhang

DOI: https://doi.org/10.1093/imanum/19.4.563

1999-01-01

IMA Journal of Numerical Analysis

Abstract:Consider a unidimensional, single-phase nonlinear Stefan problem with nonlinear source and permeance terms, and a Dirichlet boundary condition depending on the free-boundary function. This problem is important in groundwater ow. By immobilizing the free-boundary with the help of a Landau type transformation, together with a homogeneous transformation dealing with the nonhomogeneous Dirichlet boundary condition , an H 1-nite element method for the problem is proposed and analysed. Global existence of the approximate solution is established, and optimal error estimates in L 2 , L 1 ; H 1 and H 2 norms are derived for both semi-discrete and fully discrete schemes.
A Finite Element Method for a Boundary Value Problem of Mixed Type

Arthur G. Deacon,Stanley Osher

DOI: https://doi.org/10.1137/0716056

IF: 3.039

1979-10-01

SIAM Journal on Numerical Analysis

Abstract:A boundary value problem for the LavrentevBitsadze differential equation of mixed type is divided into an elliptic problem involving an unusual boundary condition on the parabolic line, and a hyperbolic problem. The elliptic problem is then converted into an equivalent variational form and shown to be well posed under certain conditions which always include the characteristic boundary case. The finite element method is applied using triangular elements and a few singular functions near the intersection of the parabolic line and the elliptic boundary. This method is shown to be second order accurate and easy to implement. Once the elliptic problem is solved, thus giving u and its derivatives along the parabolic line, the straightforward Cauchy problem is solved in the hyperbolic region. Numerical verification of these results is presented.

mathematics, applied
Exact Solutions of Equations for the Strongly-Conductive and Weakly-Conductive Magnetic Fluid Flow in a Horizontal Rectangular Channel

Mingjun Li,Xinrong Zhang,Hiroshi Yamaguchi

DOI: https://doi.org/10.4236/jemaa.2010.23025

2010-01-01

Journal of Electromagnetic Analysis and Applications

Abstract:This paper presents the results of exact solutions and numerical simulations of strongly-conductive and weakly-conductive magnetic fluid flows.The equations of magnetohydrodynamic (MHD) flows with different conductivity coefficients, which are independent of viscosity of fluids, are investigated in a horizontal rectangular channel under a magnetic field.The exact solutions are derived and the contours of exact solutions of the flow for magnetic induction modes are compared with numerical solutions.Also, two classes of variational functions on the flow and magnetic induction are discussed for different conductivity coefficients through the derived numerical solutions.The known results of the phenomenology of magnetohydrodynamics in a square channel with two perfectly conducting Hartmann-walls are just special cases of our results of magnetic fluid.
Numerical solution for the Helmholtz equation with mixed boundary condition

Wang Haibing,Liu Jijun

2007-01-01

Abstract:We consider the numerical solution for the Helmholtz equation in R2 with mixed boundary conditions. The solvability of this mixed boundary value problem is estab- lished by the boundary integral equation method. Based on the Green formula, we express the solution in terms of the boundary data. The key to the numerical re- alization of this method is the computation of weakly singular integrals. Numerical performances show the validity and feasibility of our method. The numerical schemes proposed in this paper have been applied in the realization of probe method for inverse scattering problems. Keywords Helmholtz equation, Green formula, potential theory, boundary integral equation, numerics.
A Finite-Element Method for Laplace- and Helmholtz-Type Boundary Value Problems with Singularities

XN Wu,HD Han

DOI: https://doi.org/10.1137/s0036142993258488

IF: 3.039

1997-01-01

SIAM Journal on Numerical Analysis

Abstract:Laplace- and Helmholtz-type boundary value problems with singularities are considered. A sequence of approximations to the exact boundary conditions at an artificial boundary is given. Then the original problem is reduced to a boundary value problem in a domain away from the singularities. Furthermore, finite-element approximations are applied to this problem and error estimates are obtained. Finally, some numerical examples show the effectiveness of this method.
Asymptotic Solutions for Laminar Flow Based on Blood Circulation Through a Uniformlyporous Channel with Retractable Walls and an Applied Transverse Magnetic Field

Lin Li,Ping Lin,Hong Zhang,Liancun Zheng,Xinhui Si

DOI: https://doi.org/10.1016/j.powtec.2016.12.033

IF: 5.64

2016-01-01

Powder Technology

Abstract:This paper is concerned with asymptotic solutions of a nonlinear boundary value problem (BVP), which arises in a study of laminar flow in a uniformly porous channel with retractable walls and an applied transverse magnetic field. For different ranges of the control parameters (i.e. α,Re and M) arising in the BVP, four cases are considered using different singular perturbation methods. For the first case, unlike those in the existing literature, we make use of the Lighthill method and successfully construct an asymptotic solution with high-order derivatives at the center of the channel. For the second case, under large suction we consider M2=O(1) and M2=O(Re), respectively, which will further extend the applying range of asymptotic solutions. In other cases, asymptotic solutions with a boundary layer are successfully constructed. In addition, numerical solutions presented for each case agree well with asymptotic solutions, which illustrates that the asymptotic solutions constructed in this paper are more reliable. Finally, the influences of some parameters on flow field are discussed to develop a better understanding of the flow problem.

A method for solving Laplace's equation with mixed boundary condition in electromagnetic flowmeters

Divisionally Analytical Solutions of Laplace'S Equations for Dry Calibration of Electromagnetic Velocity Probes

Study of No-liquid Calibration Technique for the Medium-and-large Diameter Electromagnetic Flowmeter

Introducing a General Analytical Method for Solving Electromagnetic Fields with Complicated Boundary

An Application of the Adomian's Decomposition Method to the Analysis of MHD Duct Flows

Reconstruction of the magnetic field in the measuring volume of an electromagnetic flow sensor

Alternating Iteration Method for Solving the Laplace Equation

Simulation of Electromagnetic Fields on Flow Boundary Layer Control

Three-dimensional MHD simulations of the electromagnetic flowmeter for laminar and turbulent flows

A Rectangular Mixed Finite Element Method with A Continuous Flux for an Elliptic Equation Modelling Darcy Flow

Hybrid Laplace transform finite element method for solving the convection–dispersion problem

A Hybrid Phase Flow Method for Solving the Liouville Equation in a Bounded Domain

Numerical Simulation for Magnetostatic Problems Based on A-λ Mixed Finite Element Method

Unified Lattice Boltzmann Method for Electric Field–Space Charge Coupled Problems in Complex Geometries and Its Applications to Annular Electroconvection

A Kind of Boundary Element Methods for Boundary Value Problem of Helmholtz Equation

A Finite Element Method for a Unidimensional Single-Phase Nonlinear Free Boundary Problem in Groundwater Flow

A Finite Element Method for a Boundary Value Problem of Mixed Type

Exact Solutions of Equations for the Strongly-Conductive and Weakly-Conductive Magnetic Fluid Flow in a Horizontal Rectangular Channel

Numerical solution for the Helmholtz equation with mixed boundary condition

A Finite-Element Method for Laplace- and Helmholtz-Type Boundary Value Problems with Singularities

Asymptotic Solutions for Laminar Flow Based on Blood Circulation Through a Uniformlyporous Channel with Retractable Walls and an Applied Transverse Magnetic Field