Abstract:There are heat transfer correlations for heat transfer analysis in single tube geometries after several experimental and theoretical heat transfer studies in these single tube geometries. This is not the case for heat transfer analysis in rod bundle geometry with regard to proposed square fuel assembly of the Supercritical-Water-Cooled Reactor (SCWR) European Atomic Energy (EURATOM) design. Thus limited heat transfer studies exist on rod bundle geometry at supercritical pressures. Heat transfer correlations with accurate prediction capabilities of coolant and wall temperatures will be helpful in carrying out heat transfer studies at supercritical pressures. This paper presents the performance of twelve selected heat transfer correlations assessed on the 1/8th bare square fuel assembly of the SCWR EURATOM design using Simulation of Turbulent flow in Arbitrary Regions Computational Continuum Mechanics C ++ based code (STAR-CCM + CFD code). The obtained numerical results were compared with the results obtained by Waata numerical experimentation. Overall, the Cheng et al. correlation provided the most satisfying prediction for the wall temperatures in all the sub-channels and captured closely Wataa's Numerical data. The maximum wall temperature was obtained in sub-channel 9, the hottest sub-channel and exceeded the design limit 620 °C by 60 °C for the Cheng correlation. The difference in temperature between the hottest and coldest sub-channels 9 and 1 respectively was approximately 80 °C. It was found that Cheng correlation is best suited for heat transfer prediction in rod bundle geometry at supercritical pressures with regard to the proposed square fuel assembly of the SCWR EURATOM design. It was also found that the different numerical tools adopted for this study and Waata study were able to capture the trends of normal, enhanced and deteriorated heat transfer regimes normally observed at supercritical pressures. Nevertheless, experimental investigations involving rod bundles adopted in this study should be conducted to validate the results obtained numerically and address the inconsistency of the conclusions drawn when compared with Waata data and other similar studies.

Analysis of the Influences of Thermal Correlations on Neutronic–thermohydraulic Coupling Calculation of SCWR

Assessment of heat transfer correlations in the sub-channels of proposed rod bundle geometry for supercritical water reactor

Analysis of Heat Transfer Characteristics in Core of Supercritical Water Cooled Reactor

NEUTRONIC/THERMAL-HYDRAULIC COUPLING ANALYSIS OF XI'AN PULSED REACTOR BASED ON RMC AND COBRA-TF

Development and Verification of Multiphysical Coupling Calculation Code for Typical Pressured Water Reactor Core

Review on neutronic/thermal-hydraulic coupling simulation methods for nuclear reactor analysis

Experimental study on heat transfer in vertical cooling tube cooled by downward flow in the passive heat removal system of SCWR

The first-principle coupled calculations using TMCC and CFX for the pin-wise simulation of LWR

Internal coupling between neutronics and thermal hydraulics with RMC/CTF and validation using vera benchmarks

Coupled Monte Carlo and Thermal-Hydraulics Modeling for the Three-Dimensional Steady-State Analysis of the Xi'an Pulsed Reactor

Research on Coupling of Neutronics and Thermal-Hydraulics Based on Stochastic Method of Neutron Transport

Research on RMC neutronics-thermal hydraulics coupling based on universal coupling methodology

Multi-physics coupling analysis on neutronics, thermal hydraulic and mechanics characteristics of a nuclear thermal propulsion reactor

Sub-channel Analysis of CANDU–SCWR and Review of Heat-Transfer Correlations

Discussion and perspectives for improvements of heat transfer correlation capabilities for fluids at supercritical pressures

Neutronic and Thermal-Mechanical Coupling Schemes for Heat Pipe Cooled Reactor Designs

An Internal Coupling Method Between Neutronics and Thermal-Hydraulics with RMC and CTF

Thermal Analysis on NAC-STC Spent Fuel Transport Cask under Different Transport Conditions

A new neutronics-thermal-mechanics multi-physics coupling method for heat pipe cooled reactor based on RMC and OpenFOAM

Multi-Mesh Approach for Geometry-Independent Neutronic/Thermal-Hydraulics Coupling Analyses Using RMC and Ansys Fluent

Numerical Verifications on Heat Transfer to Supercritical Water Flowing Upward in a 4-m Long Bare Vertical Tube