Abstract:In recent years a considerable amount of research has been undertaken in the development of the piezoelectric actuator for active structural acoustic control (ASAC). Some researchers have concentrated on the optimisation of the parameters of the piezoelectric actuators; for instance, the number, sizes, locations and voltages applied to the actuators to minimise either structural vibration or radiated sound power . In the work of Wang et al. , a mathematical formulation for the optimisation of the locations of piezoelectric actuators in a feedforward control implementation of ASAC was given. They demonstrated that optimally located piezoelectric actuators can provide a large reduction in the amount of sound power radiated, and are observed to perform better than actuators in arbitrarily chosen locations. Based on the object function selected in their work, Wang et al. found that properly locating one piezoelectric actuator generally gives greater reduction of radiated sound power than using two or three actuators. Recently, Varadan et al. 4 have reported on the optimisation of the placement of circular disk-shape piezoelectric actuators on a clamped rectangular plate, using the finite element method. They found that the optimal locations of piezoelectric actuators to minimise sound radiation are near the corners rather than the centre of the plate. This is because the edges and corners of flat plates contribute most to the radiated sound power at frequencies below the plate critical frequency, the frequency range of the results reported. Another application of PZT actuators their use to excite a panel control sources to replace loudspeakers in ANVC (Li et al. ). In the work of Li et al. , a tuned curved panel sound source for use with active systems for controlling transformer sound was developed. If this kind of sound source is used in the place of loudspeakers, the number of control sources and the complexity of the controller can be reduced substantially. To prevent the interaction and cancellation of the sound radiation from the two sides of the panel, a cavity was coupled to one side of the panel. The reasons for using a curved panel rather than flat panel are twofold: first a curved panel is more easily excited by piezoelectric patch actuators because the bending vibration of the curved panel couples better with the extensional motion of the actuators; and second, it is not possible to adjust the resonance frequencies of the efficient modes of a flat panel very easily. In this paper, a curved panel with a backing cavity driven by rectangular PZT actuators 7 has been modelled. Simple optimisation procedures for sizes and locations of the PZT actuators on the panel are given. Because the research described in this paper concerns the design of a resonant curved panel as a sound source, only optimal results for some efficient natural modes are presented. The objective of the optimisation is to maximise the structural response (velocity) of the curved panel vibrating in particular resonant modes.

Control Strategies and Mechanisms for Active Control of Sound Transmission into a Cabin Enclosure.

A Method of Sound Field Control Using Beam Deflection

Control of Scattering Sound Field from a Cylindrical Shell Using Beam Deflection

Active Radiation Noise Control of Airplane's Cabin Using Piezoelectric Elements

Experimental Research of Noise Control in the Fighter Cockpit Using Microperforated Panel Absorber Structure

Mechanisms of Active Control of Noise Transmission Through a Panel into a Cavity Using a Point Force Actuator on the Panel

Sound transmission control through a hybrid smart double sandwich plate structure

Study on active noise control inside automobile cabin

Experimental Study of an Active Window for Silent and Comfortable Vehicle Cabins

Theory and Scheme of Active Control on Structural Interior Noise

Enhancing sound insulation performance with active constrained layer damping plates at low frequencies

Active Control of Sound Reflection, Absorption and Transmission Using Thin Panels

Study on Active Control of Sound Radiation From a Baffle in Sonar Equipment

Mechanisms of Active Control of Sound Radiation from an Opening with Boundary Installed Secondary Sources.

Control of sound transmission into a hybrid double-wall sandwich cylindrical shell

Active control of noise in plate-cavity coupled systems using the pole placement method

Acoustic-Structural Coupled Modal Analysis Method and It S Application in Vehicle Interior Noise Control

Optimal Sizes and Locations of Piezoelectric Actuators for Curved Panel Sound Sources

Secondary source and error sensing strategies for the active control of sound transmission through a small opening

Causal feedforward control of a stochastically excited fuselage structure with active sidewall panel

Active Sound Radiation Control with Secondary Sources at the Edge of the Opening