Abstract:In order to provide technical parameters for industrial model test,methylaluminoxane (MAO) is used as co-catalyst,ethylene/1-hexene copolymerization reaction is carried out catalyzed by CpCN-CGC in n-heptane.The effects of temperature,ethylene pressure,ratio of aluminum to zirconium,hydrogen pressure,and the concentration of 1-hexene on the catalytic behavir and polymer's properties are also studied.It is found that the catalytic activity increase first and then reduce as the temperature increase from 100 to 140 ℃,but the molecular weight of polymer decrease continuously.When the pressure of hydrogen increased from 0.1 to 0.8 MPa,the similar situations happen again.When the pressure of ethylene increase from 0.4 to 1.8 MPa,the catalytic activity increase first and then reduced but the molecular weight of polymer increase contuinually.However,when the ratio of AL/Zr augmented from 500 times to 1 000 times,the catalytic activity increase contuinually but the molecular weight of polymer tends to decrease in general.The optimum technological conditions are obtained:catalyst dosage is 10 μmol,the ratio of Al/Zr =700,polymerization temperature is 110 ～120 ℃,the pressure of ethylene is 1.2 ～1.4 MPa,the dosage of 1-hexene is 20 mL,and the polymerization time is 30 min,as a result,the catalytic activity reaches up to 106 g/(mol-Zr · h) and the insertion of 1-hexene in copolymer reaches up to 8.34％.The copolymer is characterized by 13C NMR,DSC and GPC,and the dyad and triad distribution and number-average sequence length of these copolymers are quantitatively determined,and found that there are many types branch chain in polymer and the mechanism was offered,however,it is also found there are alternating copolymer HEHE fragment exists in copolymer.

13C NMR Study of Monomer Composition and Sequence Distribution in Ethylene/propylene/1‐octene Terpolymers

Ethylene polymerization by diphenyl ether bridged dinuclear titanocenes/MAO

Engineering Ethylene/1-Hexene Copolymers from Ethylene Stock with a Model-Guided Catalyst Feeding Policy

13 C-NMR STUDY OF ETHYLENE-1-OCTENE COPOLYMERS

Tandem Action of Sns-Cr and Cgc-Ti in Preparation of Ethylene-1-Hexene Copolymers from Ethylene Feedstock

Ethylene/Propylene Copolymerization with Half-Titanocene/Mao Catalyst - Ii. C-13-Nmr Analysis of Ethylene-Propylene Copolymer

Studies on composition and molecular structure of high impact polypropylene

Modeling and Kinetics of Tandem Polymerization of Ethylene Catalyzed by Bis(2-Dodecylsulfanyl-ethyl)amine-crcl3 and Et(Ind)2ZrCl2

13C NMR Studies of Ethylene-Propylene Copolymers Prepared with Homogeneous Metallocene-Based Ziegler-Natta Catalysts

Characterization of Intramolecular Composition Heterogeneity of Metallocene-Based and Conventional Ethylene-Butene Copolymers Using Tref/Dsc

Comonomer Sequence Distribution In Metallocene-Based Ethylene/1-Butene (S-34) And Ethylene/1-Hexene (S-43) Copolymers

C-13 NMR study of the sequence distribution of styrene oligomers and polymers

ETHYLENE/PROPYLENE COPOLYMERIZATION WITH HALF-TITANOCENE/MAO CATALYST III. CHARACTERIZATION AND STRUCTURE ANALYSIS OF ETHYLENE-PROPYLENE COPOLYMER

Separation and identification of ethylene-propylene block copolymer

Study on the Structure and Property of Metallocene Ethylene/1-Heptene and Ethylene/1-Octene Copolymers

Synthesis and Characterization of Copolymer of Ethylene and 1-Hexene by Carbon Bridge CpCN-CGC

Study of Heterogeneity of Ethylene/1-Octene Copolymers Synthesized with Zirconium and Titanium Complexes Bearing Diamine-bis(phenolate) Ligands

The Effect of Feeding Sequence on the Structure and Properties of the Ethylene/1-Octene Copolymer in the Semi-Continuous Polymerization Reaction System

Synthesis and Characterization of Short-Chain Branched Polyethylene

Microstructure of Ethylene/propylene Random Copolymers Prepared by a Fluorinated Bis(phenoxy-Imine) Ti Catalyst

Propylene Polymerization with Α-Keto-β-diimine Initiators Proceeds Via Enantiomorphic Site Control