Abstract:Multiscale microstructure mesh wicks (MMWs) are widely used in the fabrication of ultrathin heat pipes (UTHPs) due to their excellent capillary properties. In this study, multiscale structures, including superhydrophilic nanosheet structures and microparticles, were prepared on copper meshes by a simple chemical etching method to enhance the capillary properties of wicks. The effects of chemical etching time on wick morphology, composition and capillary rise were investigated, and the effects of high-temperature sintering on the capillary performance of wicks were compared to provide application guidance for evaluating the heat transfer performance of UTHPs. The results indicated that the chemical etching caused the self-growth of superhydrophilic CuC 2 O 4 nanosheet structures on the copper mesh surface compared with the untreated surface, and the maximum capillary rise velocity and the wicking coefficient could reach 8.4 mm/s and 404.457 mm 2 /s, respectively. After high-temperature sintering, the superhydrophilic CuC 2 O 4 on the wick surface turns into CuO and Cu through reduction and pyrolysis reactions, and the nanosheet structure also turns into particle structure and bridges into microchannels at the dense particles. Due to the change of surface structure and chemical composition, the capillary performance of the wicks decreased, and the maximum capillary rise height could reach 80.6 mm and the maximum capillary performance parameter could reach 117.419 mm 2 /s, which were approximately 11.43% and 70.97% lower than that without high-temperature sintering, respectively.

Porous Cu Nanowire Aerosponges from One-Step Assembly and their Applications in Heat Dissipation.

High-performance supercapacitors of Cu-based porous coordination polymer nanowires and the derived porous CuO nanotubes.

Innovative Multiphase Ultrasonic-Assisted Method for High-Purity, Stable, and Cost-Effective Copper Nanowire Synthesis

G030084 Fabrication of High Density Cu Nanowire Array by Template Method and Its Evaluation

Three-dimensional carbon nanotube sponge-array architectures with high energy dissipation.

Self-assembly of 3D Carbon Nanotube Sponges: A Simple and Controllable Way to Build Macroscopic and Ultralight Porous Architectures.

J212025 Fabrication of Nanowire Surface Fastener on Flexible Substrate and Its Electrical and Mechanical Properties

Resilient and Antipuncturing Si 3 N 4 Nanofiber Sponge

Enhancement of Evaporative Heat Transfer on Carbon Nanotube Sponges by Electric Field Reinforced Wettability

Novel micro‐spherical Si 3 N 4 nanowire sponges from carbon‐doped silica sol foams via reverse templating method

Ambient Aqueous-Phase Synthesis of Copper Nanoparticles and Nanopastes with Low-Temperature Sintering and Ultra-High Bonding Abilities

Enhanced capillary performance of nanostructures copper woven mesh wick for ultrathin heat pipes

Soft, highly conductive nanotube sponges and composites with controlled compressibility.

Directly Growing Nanowire-Assembled Nanofibrous Ceramic Foams with Multi-Lamellar Structure Via Freeze-Casting Process

Ultralight, Superelastic, and Washable Nanofibrous Sponges with Rigid-Flexible Coupling Architecture Enable Reusable Warmth Retention

A Facile Route to Isotropic Conductive Nanocomposites by Direct Polymer Infiltration of Carbon Nanotube Sponges

Carbon Nanotube Sponges, Aerogels, and Hierarchical Composites: Synthesis, Properties, and Energy Applications

Fabrication of a 3D Porous Silver Wire Based on a Template-Assisted Electroless Deposition Method

Synthesis of Ultralong Copper Nanowires for High-Performance Transparent Electrodes

Covalently bonded nitrogen-doped carbon-nanotube-supported Ag hybrid sponges: Synthesis, structure manipulation, and its application for flexible conductors and strain-gauge sensors

One-Step Fabrication of Copper Nanopillar Array-Filled AAO Films by Pulse Electrodeposition for Anisotropic Thermal Conductive Interconnectors