Abstract:The hot deformation behavior of a powder metallurgy (P/M) Ni-base superalloy FGH96 was investigated at the temperature (T) of 1050–1140°C, strain rate (ε˙) of 0.002–1.0s−1, and the height reduction of 20–50% via isothermal hot compression experiment. The flow behavior and the microstructural mechanism of the synthesized superalloy were systematically studied. The processing map was constructed based on the experiment data to evaluate the efficiency of power dissipation and recognize the instability regimes for forging process determination. The processing map with the strain of 0.15 exhibits a smooth and small variation of η and predicts a little instability regime confined at (T: 1050°C, ε˙:1.0 s−1), attributed to the previous particle boundary (PPB) cracks. The map obtained at the strain of 0.65 reveals a large domain with the efficiency above 40% and predicts two instability regimes at around (1050°C, 1s−1) and located in the regime of (T: 1080–1140°C, ε˙:0.002−0.01 s−1), respectively. The optimum processing condition is identified as (T: 1140°C, ε˙:1.0 s−1), which presented the highest efficiency in hot working process, as well as the obtained fine microstructure after the hot processing. Via microstructure characterization and observation, it is concluded that the dynamic recrystallization (DRX) occurred at the PPBs in the P/M superalloy. The DRX and the strain rate sensitivity exponent m are both affected by true strain. The local DRX presents a relatively low m in a small strain compression. With an increase of strain, the fraction of the recrystallized grains increases with m. The global DRX, however, presents a relatively high m in a large strain compression. It is thus indicated that the superplasticity of FGH96 superalloy can be realized at a slow strain rate such as 0.001s−1 and the deformation temperature of 1110°C, near to the γ′-transus temperature, by using the uniformly fine-grained superalloys as well as the high temperature superplastic forming equipment.

Spheroidization and dynamic recrystallization mechanisms of a novel HIPed P/M superalloy during hot deformation

Modeling Dynamic Recrystallization Behavior in a Novel HIPed P/M Superalloy during High-Temperature Deformation

Morphological Evolution and Dissolution Mechanisms of Γ′ Phase in a Novel HIPed P/M Superalloy in Hot Deformation Process

Plastic deformation and dynamic recrystallization of a powder metallurgical nickel-based superalloy

Hot Deformation Characteristics of GH141 Superalloy

Investigation on Dynamic Recrystallization of FGH96 Powder Metallurgy Superalloy

Thermal Deformation and Dynamic Recrystallization of a Novel HEXed P/M Nickel-Based Superalloy

Hot Deformation Behavior and Microstructure Characterization of Hiped Fgh4096 Superalloy Containing High Strain Rate

High Temperature Deformation Behavior of Hot Isostatically Pressed P/M FGH4096 Superalloy

Modeling the rheological behaviour of a novel HIPed P/M superalloy

Microstructure evolutions of a powder metallurgy superalloy during high-strain-rate deformation

Hot Deformation Characteristics and Dynamic Recrystallization Mechanisms of a Novel Nickel‐Based Superalloy

Hot Compressive Deformation Behavior and Microstructure Evolution of HIPed FGH96 Superalloy

Microstructure Evolution Characteristics of a Powder Metallurgy Ni-based Superalloy During Hot Deformation

Formation and elimination mechanisms of prior particle boundaries in a new powder metallurgy superalloy

Investigation on hot deformation behavior of P/M Ni-base superalloy FGH96 by using processing maps

Dynamic Recrystallization of the Hot Isostatically Pressed P/M Superalloy FGH4096 in Hot Working Process

Investigation on Hot Deformation Behavior of P/M Superalloy FGH4096

Post-dynamic recrystallization behavior of a powder metallurgy Ni-Co-Cr based superalloy under different deformation conditions

Hot Deformation Behavior of a Powder Metallurgy Superalloy with High γ′ Content

Microstructure Evolutions and Nucleation Mechanisms of Dynamic Recrystallization of A Powder Metallurgy Ni-Based Superalloy During Hot Compression