Abstract:Ultra-fine grained ferrite steels have higher strength and better toughness than the normal ferrite steels because of their micrometer or sub-micrometer sized grains. In this paper the ultra-fine grained steel SS400 is welded by CO2 laser. The shape of weld, cooling rate of HAZ, width of HAZ, microstructures and mechanical properties of the joint are discussed. Experimental results indicate that laser beam welding can produce weld with a large ratio of depth to width. The cooling rate of HAZ of laser beam welding is fast, the growth of prior austenite grains of HAZ is limited, and the width of weld and HAZ is narrow. The microstructures of weld metal and coarse-grained HAZ of laser beam welding mainly consist of BL + M (small amount). With proper laser power and welding speed, good comprehensive mechanical properties can be acquired. The toughness of weld metal and coarse-grained HAZ are higher than that of base metal. There is no softened zone after laser beam welding. The tensile strength of a welded joint is higher than that of base metal. The welded joint has good bending ductility. Feinkornbaustähle mit ultra-feinem Korn in der Größenordnung von Mikrometern oder darunter weisen höhere Festigkeiten und bessere Zähigkeiten als die normalen ferritischen Stähle auf. In dieser Arbeit wird ein solcher Feinkornbaustahl SS 400 mit CO2-Laser geschweißt. Die Form der Schweißnaht, die Abkühlgeschwindigkeit in der Wärmeeinflußzone (WEZ) die Breite der WEZ, die Mikrostrukturen und die Festigkeitseigenschaften der Naht werden diskutiert. Versuchsergebnisse weisen darauf hin, dass das Laserstrahlschweißen Schweißverbindungen mit einem großen Verhältnis aus Schweißnahttiefe und -breite erzeugen kann. Die Abkühlgeschwindigkeit in der WEZ ist beim Laserstrahlschweißen hoch, das Wachstum ehemaliger Austenitkörner in der WEZ ist begrenzt; sowohl Schweißnaht als auch WEZ sind schmal ausgebildet. Die Mikrostrukturen der Schweißnaht und der grobkörnigen WEZ bestehen überwiegend aus unterem Bainit und kleinen Gehalten an Martensit. Mit geeigneter Energiezufuhr und Schweißgeschwindigkeit lassen sich gute Festigkeitseigenschaften erzielen. Die Naht und die grobkörnige WEZ weisen bessere Duktilitätswerte als der Grundwerkstoff auf. Nach dem Laserstrahlschweißen tritt keine Erweichungszone auf. Die Zugfestigkeit der Schweißverbindung liegt ebenfalls über der des Grundwerkstoffes. Die Schweißverbindung besitzt gute Biegeeigenschaften.

Laser welding of carbon-fibre-reinforced polyetherketone and 304 stainless steel: Cost-effective approach using prefabricated holes

Study on microstructures and mechanical performance of laser transmission welding of poly-ether-ether-ketone (PEEK) and carbon fiber reinforced PEEK (CFR-PEEK)

Laser joining of CFRTP to metal: A review on welding parameters, joint enhancement, and numerical simulation

Blue laser welding of 7075-T6 aluminum alloy and carbon fiber reinforced polyetheretherketone

Mass Fabrication of Microholes in Aviation Kerosene Filters Using the Back-water-assisted Picosecond Laser Drilling Technique

Interlayer bonding improvement of PEEK and CF-PEEK composites with laser-assisted fused deposition modeling

Laser welding process and strength enhancement of carbon fiber reinforced thermoplastic composites and metals dissimilar joint: A review

Research on laser rivet welding to achieve hybrid joining of CFRP and high-strength steel

Fiber Laser Welding of 1700-MPa, Ultrahigh-Strength Steel

Influence of laser welding power on steel/CFRP lap joint fracture behaviors

Effects of Laser Premelting Treatment on Microstructure and Mechanical Properties of High-Strength Steel Weld Obtained by Laser-MAG Hybrid Welding

Investigation on the joining process and strength of laser circle welding between Al5052 and CFRP dissimilar materials

Laser Welding of AISI 316L Stainless Steel Produced by Additive Manufacturing or by Conventional Processes

Reducing the taper and the heat-affected zone of CFRP plate by Micro fluid assisted laser induced plasma micro-drilling

Effect of surface texture spacing on interface heat transfer and tensile property of laser‐welded steel/ CFRTP joint

Machining holes in CFRP with laser "drilling + boring" hybrid technique

Laser-assisted direct-joining of carbon fibre reinforced plastic with thermosetting matrix to polycarbonate sheets

Laser Welding of Metal-Polymer-Metal Sandwich Panels

Laser surface treatment to enhance the adhesive bonding between steel and CFRP: Effect of laser spot overlapping and pulse fluence

Study of Welding Ultra-Fine Grained Ferrite Steel by CO2laser

Comparative investigations on machinability and surface integrity of CFRP plate by picosecond laser vs laser induced plasma micro-drilling