Abstract:Cathode buffer layer (CBL) is one of the key issues influencing the performance of organic solar cells. In this article, a nanocomposite of zinc oxide nanoparticles (ZnO) together with a conjugated polymer, poly[(9,9-bis(3'-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctyl)-fluorene] (PFN) was developed, and used as the CBL for solution processed inverted organic solar cells (OSC). In comparison with the bare ZnO, PFN or ZnO/PFN stacked layer, the ZnO:PFN nanocomposite CBL employing device showed superior device performance, in particular significantly improved fill factor. Optimized power conversion efficiency (PCE) of P3HT:PC61BM and PTB7:PC61BM device using ZnO:PFN composite CBLs reached to 3.56% and 7.17%, respectively. Influences of the mixing ratio and the layer thickness of the ZnO:PFN nanocomposite CBL on solar cell performance were carefully studied, and results indicated that ZnO:PFN CBL showed a wide tolerance of blend ratio and layer thickness. In particular, no obvious thickness dependent-device performance was found, even when the CBL layer thickness was higher than 125nm, providing a good printing processibility of the nanocomposite. Photoelectron spectroscopy, photoluminescence, as well as electric conductivity of the ZnO:PFN films were studied, and the results were compared with that of the other three reference CBLs. Results demonstrated that the interaction between ZnO and PFN decreases the work function of the blended film, leading to a more favorable energy level alignment for electron injection at the interface. Analysis on the dark J–V curves of the solar cells revealed that device using ZnO:PFN CBL had the best diode characteristics including lowest reverse saturated current density (J0), ideal factor (n), and series resistance (Rs), and highest shunt resistance (Rsh). Such an improvement was ascribed to the defect passivation by the conjugated polymer, which led to an improved charge carrier selectivity of the CBL and consequently enhanced the FF of the solar cells. In addition, long-term stability of organic solar cells was also improved by using ZnO:PFN nanocomposite as the CBL. The current work provides a valuable guideline for the development of high performance cathode buffer layer material for printable organic solar cells.

Simple O2 Plasma-Processed V2O5 As an Anode Buffer Layer for High-Performance Polymer Solar Cells.

Aqueous Solution‐processed NiOx Anode Buffer Layers Applicable for Polymer Solar Cells

Solution-processed vanadium oxide as an anode interlayer for inverted polymer solar cells hybridized with ZnO nanorods

A Low-Cost and Low-Temperature Processable Zinc Oxide-Polyethylenimine (zno:Pei) Nano-Composite As Cathode Buffer Layer for Organic and Perovskite Solar Cells

Novel Cathode Buffer Layer Enabling over 21.6%/20.9% Efficiency in wide bandgap/inorganic Perovskite Solar Cells

Water‐Induced Formation of α‐MoO 3 Microcrystals as Anode Buffer Layer for Highly Efficient Polymer Solar Cells

An Ultraviolet‐Deposited MoO3 Film As Anode Interlayer for High‐Performance Polymer Solar Cells

Zinc Oxide: Conjugated Polymer Nanocomposite As Cathode Buffer Layer for Solution Processed Inverted Organic Solar Cells

Efficient Inverted Polymer Solar Cells with ITO Cathode Modified by Zinc Oxide and Polyethylene Oxide Bilayers

High-Performance Ultrathin BiVO4 Photoanode on Textured Polydimethylsiloxane Substrates for Solar Water Splitting

Solution-Processed Copper Iodide As an Inexpensive and Effective Anode Buffer Layer for Polymer Solar Cells

Low Temperature Aqueous Solution-Processed Zno and Polyethylenimine Ethoxylated Cathode Buffer Bilayer for High Performance Flexible Inverted Organic Solar Cells

Ultrathin chromium oxide buffer layer by reactive thermal deposition for high-performance semitransparent perovskite solar cells

A Versatile Buffer Layer for Polymer Solar Cells: Rendering Surface Potential by Regulating Dipole

Simple and Low‐Cost Vanadyl Oxalate as Hole Transporting Layer Enables Efficient Organic Solar Cells

Vanadium Pentoxide Modified Polycrystalline Silicon Anode for Active-Matrix Organic Light-Emitting Diodes

Advances in Top Transparent Electrodes by Physical Vapor Deposition for Buffer Layer‐Free Semitransparent Perovskite Solar Cells

Enhanced Performance And Stability Of Polymer Solar Cells By In Situ Formed Alox Passivation And Doping

Solution Processed Inorganic V2Ox As Interfacial Function Materials for Inverted Planar-Heterojunction Perovskite Solar Cells with Enhanced Efficiency

Self-assembled, aligned ZnO nanorod buffer layers for high-current-density, inverted organic photovoltaics

Organic Salt Buffer Layer Enables High‐Performance NiOx‐Based Inverted Perovskite Solar Cells