Abstract:There has been considerable interest recently in the development of fiber optic sensors based on white light interferometry. The use of such a technique for distributed strain or temperature sensing in advanced composite or other structural materials has been discussed in several recent articles. Fiber optic Michelson sensor arrays are of particular interest for such applications because a number of reflective-type sensors networked either in a serial or a parallel topology may be interrogated by use of a common path-length variable reference, thus keeping the system cost down. Several schemes have been reported for multiplexing this type of sensors. These include coherence turning, time-division, Spatial division, duplicate fiber optic switch and 1 x N star coupler multiplexing technique. In this paper, we propose and demonstrate a white light twin-sensor-array scheme that measures the absolute optical path lengths between each fiber segment and reflective surfaces. The sensing principle is shown in Figure 1. The broadband LED source is directly coupled into the fiber optic Michelson interferometer by passing thorough a 3 dB coupler and launched into the twin-sensor-array. The twin-sensor-array consist of 2 x N fiber segments (N twin-sensors) connected in series with partial reflectors in-between the adjacent fiber segments, configuring a Michelson interferometer based multiplexed fiber optic sensor array. The reflected signals of each sensor pair retime and travel in the same path towards to the PIN detector end. One arm of the fiber optic Michelson interferometer as optical path adjusting part has been used to demodulate the twin-sensor-arrays. So that each individual sensor pair is corresponding to a unique interference peak due to the optical path length is different each other. For a sensor pair, if one of the twin sensors is used as a strain sensor, while the other sensor can be used as a temperature compensated sensor. Therefore, the proposed sensing scheme will be useful for temperature compensation of distributed strain measurement. An important application of the sensing system could be deformation sensing in smart structures. (Figure Presented) Figure 2 shows a twin-sensor-arrays has been embedded in a concrete structure. A number of fiber segments pairs l i and l′i are connected in serial to form the twin-sensor-arrays, which is further connected to a lead in/out fiber of length L0 and L′0. In the sensing system, the length of the two lead in/out fiber cables has been chosen as nearly equal, and same as for each fiber segment pairs, i.e.: the optical path length of the reference arm L′0 can be varied through the use of a moving graded index (GRIN) lens (as shown in Fig. 1(a)) or a scanning right angle mirror (as shown in Fig. 1(b)). One adjusts the optical path of the reference arm to match and trace fhe change of the twin-fiber-sensor gauge length in each sensing pairs. When the optical-path difference (OPD) between the sensing branch and the reference branch falls within the coherence length of the light source, a white light fringe pattern is produced. The central fringe, which is located in the center of the fringe pattern and has the highest amplitude, corresponds to the exact path match of the two optical paths. Fiber optic white light interferometric twin sensor array multiplexing technique has been demonstrated, which the matching multi-wave was demodulated by a moving GRIN lens or a right-angle mirror. The fiber optic sensors multiplexing capacity is strongly depend on the light source power of the sensing system. The proposed sensing scheme will be useful for the measurement of temperature or strain. An important application could be deformation sensing in smart structures. By incorporating fiber optic twin sensor array into structures such as large-scale buildings, bridges, dams, tunnels and highways, smart structures can be realized for situations where material strains must be monitored throughout the lifetime of the structure. © 2006 Taylor & Francis Group.

Multiplexed Multi-Longitudinal Mode Fiber Laser Sensor.

Ameliorated Spatial Division Multiplexing System of FBG Sensors Based on Novel Wavelength Detection and Demodulation Technique

Strain Sensor Based on Gourd-Shaped Single-Mode-multimode-single-mode Hybrid Optical Fibre Structure.

Multilongitudinal Mode Fiber Laser for Strain Measurement

Multiplexing technique of optical fiber displacement sensor based on heterodyne interference with frequency-modulated semiconductor laser

Multiplexing Optical Fiber Displacement Sensor Based on Heterodyne Interference with Frequency-Modulated Laser Diode

Twin-core fiber sensor integrated in laser cavity

Simultaneous wavelength and frequency encoded microstructure based quasi-distributed temperature sensor

Modulated Pulses Based High Spatial Resolution Distributed Fiber System for Multi-Parameter Sensing

Semiconductor optical amplifier fiber-ring laser for FBG dynamic strain sensing with an adaptive two-wave mixing demodulator

Multiple fiber optic twin-sensor-array based on Michelson optical low-coherence reflectometer

Multiplexed static FBG strain sensors by dual-comb spectroscopy with a free running fiber laser.

Optical Coherence-Multiplexed Sensors Based on In-Fiber Michelson

Fiber Bragg grating sensing multiplexing method using photonic lantern spatial mode diversity

Three-Wavelength Fiber Laser Sensor With Miniaturization, Integration for the Simultaneous Measurement of Underwater pH, Salinity, Temperature, and Axial Strain

Twin Multiplexing Strain Sensing Array Based on a Low-Coherence Fiber Optic Mach–Zehnder Interferometer

Dual-Parameter Active Fibre Sensor Based On Modal Interference In Few-Mode Fibres

High-Resolution Strain/Temperature Sensing System Based on A High-Finesse Fiber Cavity and Time-Domain Wavelength Demodulation

Multiplexed Static FBG Strain Sensors by Dual-Comb Spectroscopy with a Free Running Fiber Laser

Simple Hybrid Wire-Wireless Fiber Laser Sensor by Direct Photonic Generation of Beat Signal.

Simultaneous temperature and strain sensing using few-mode fiber in a single-ended BOTDA system