Abstract:The use of superhydrophobic surfaces in a broad range of applications is receiving a great deal of attention due to their numerous functionalities. However, fabricating these surfaces using low-cost raw materials through green and fluorine-free routes has been a bottleneck in their industrial deployment. This work presents a facile and environmentally friendly strategy to prepare mechanically robust superhydrophobic surfaces with engineered lotus leaf mimetic multiscale hierarchical structures via a hybrid route combining soft imprinting and spin-coating. Direct soft-imprinting lithography onto starch/polyhydroxyurethane/cellulose nanocrystal (SPC) films formed micro-scaled features resembling the pillar architecture of lotus leaf. Spin-coating was then used to assemble a thin layer of low-surface-energy poly(dimethylsiloxane) (PDMS) over these microstructures. Silica nanoparticles (SNPs) were grafted with vinyltriethoxysilane (VTES) to form functional silica nanoparticles (V-SNPs) and subsequently used for the fabrication of superhydrophobic coatings. A further modification of PDMS@SPC film with V-SNPs enabled the interlocking of V-SNPs microparticles within the cross-linked PDMS network. The simultaneous introduction of hierarchical microscale surface topography, the low surface tension of the PDMS layer, and the nanoscale roughness induced by V-SNPs contributed to the fabrication of a superhydrophobic interface with a water contact angle (WCA) of ∼150° and a sliding angle (SA) of <10°. The PDMS/V-SNP@SPC films showed an ∼52% reduction in water vapor transmission rate compared to that of uncoated films. These results indicated that the coating served as an excellent moisture barrier and imparted good hydrophobicity to the film substrate. The coated film surfaces were able to withstand extensive knife scratches, finger-rubbing, jet-water impact, a sandpaper-abrasion test for 20 cycles, and a tape-peeling test for ∼10 repetitions without losing superhydrophobicity, suggesting superior mechanical durability. Self-cleaning behavior was also demonstrated when the surfaces were cleared of artificial dust and various food liquids. The green and innovative approach presented in the current study can potentially serve as an attractive new tool for the development of robust superhydrophobic surfaces without adverse environmental consequences.

Lotus Leaf-Like Dual-Scale Silver Film Applied As A Superhydrophobic and Self-Cleaning Substrate

Super-hydrophobic and Self-cleaning PVDF Film Fabricated by Chemical Bath Deposition

Fabrication of Self-Cleaning Polyvinylidene Fluoride Film

Superhydrophobic poly(vinylidene fluoride) film fabricated by alkali treatment enhancing chemical bath deposition

Superhydrophobicity of polyvinylidene fluoride membrane fabricated by chemical vapor deposition from solution

Fabrication of Self‐cleaning Poly(vinylidene Fluoride) Membrane with Micro/nanoscaled Two‐tier Roughness

Facile Fabrication of Superhydrophobic Nanocomposite Coatings Based on Water‐Based Emulsion Latex

Abrasion‐Resistant, Hot Water‐Repellent and Self‐Cleaning Superhydrophobic Surfaces Fabricated by Electrophoresis of Nanoparticles in Electrodeposited Sol–Gel Films

Fabrication of flexible superhydrophobic biomimic surfaces

Fabrication of biomimetic superhydrophobic surface with controlled adhesion by electrodeposition

Fabrication of Super-Hydrophobic Film with Dual-Size Roughness by Silica Sphere Assembly

Lotus Leaf Inspired Robust Superhydrophobic Coating from Strawberry-Like Janus Particles

Robust and Eco-Friendly Superhydrophobic Starch Nanohybrid Materials with Engineered Lotus Leaf Mimetic Multiscale Hierarchical Structures

Superhydrophobic materials with good oil/water separation and self-cleaning property

Durable Biomimetic Two-Tier Structured Superhydrophobic Surface with Ultralow Adhesion and Effective Antipollution Property

Superhydrophobic Waxy-Dendron-Grafted Polymer Films Via Nanostructure Manipulation

Fabrication of Superhydrophobic Surface by a Laminating Exfoliation Method

Superhydrophobic Surfaces Fabricated by Femtosecond Laser with Tunable Water Adhesion From Lotus Leaf to Rose Petal.

Fabricating Super‐Hydrophobic Lotus‐Leaf‐Like Surfaces Through Soft‐Lithographic Imprinting

Design of Mechanical Robust Superhydrophobic Cu Coatings with Excellent Corrosion Resistance and Self-Cleaning Performance Inspired by Lotus Leaf

Fabrication of Stable Superhydrophobic Surface with Low Adhesion on Aluminum Foil