Abstract:Flexible superhydrophobic surfaces have been attracting more and more attention due to their foldable property. However, the superhydrophobic structure was easily damaged or destroyed owing to their poor interfacial force between substrate and superhydrophobic coating. Herein, fluorinated silica nanoparticles (F-SiO 2 ) were sprayed onto the wet poly(amide–imide) (PAI) surface, which made F-SiO 2 easily went into PAI substrate to enhance the durability of superhydrophobic surface. The PAI/F-SiO 2 flexible surface exhibited a water contact angle (CA) of beyond 160° and a sliding angle (SA) of as low as 3°, while the tensile strength (34 MPa) was comparable to that of PAI substrate (35.8 MPa). Encouragingly, the superhydrophobicity and hierarchical porous structure of PAI/F-SiO 2 surface were maintained even they were folded by 5000 times or underwent sandpaper abrasion test (500 cm of wear on a 1200 grit sandpaper under 50 g load), while the nanocomposites failed the sandpaper abrasion test when F-SiO 2 were sprayed onto completely dried PAI surface. More importantly, the CA and SA just slightly decreased when PAI/F-SiO 2 surfaces were heated at 300 °C for 24 h due to the unique surface morphology and high thermal stability of PAI, which is one of the highest thermal stabilities for flexible superhydrophobic films. In addition, PAI/F-SiO 2 surfaces maintained superhydrophobic after hot water jet impact, acid–base immersing, UV irradiation, and ultrasonic treatment, indicating the fabricated surfaces could be used for practical application especially under harsh conditions. Furthermore, the superhydrophobic surfaces possessed icephobic properties. It should be noted that PAI/F-SiO 2 surfaces showed such excellent properties, although their fabricating procedure did not undergo any optimization. This wet spraying method was also used to fabricate flexible superhydrophobic surfaces with other polymers as substrates such as poly(acrylic acid) (PAA), thermoplastic polyurethane (TPU), polystyrene (PS), and poly(vinyl alcohol) (PVA). Therefore, the simple strategy provided a general route to prepare flexible superhydrophobic films with high durability.

Fabrication of flexible superhydrophobic biomimic surfaces

Fabrication of Flexible Superhydrophobic Films by Lift-Up Soft-Lithography and Decoration with Ag Nanoparticles

Fabrication of biomimetic superhydrophobic surfaces inspired by lotus leaf and silver ragwort leaf.

Fabrication of Super-Hydrophobic Film with Dual-Size Roughness by Silica Sphere Assembly

Biomimetic Superhydrophobic Films with an Extremely Low Roll-Off Angle Modified by F16CuPc via Two-Step Fabrication

Fabrication of Superhydrophobic Polymer Films with Hierarchical Silver Microbowl Array Structures

Fabrication of Biomimetic Superhydrophobic Surface Using Hierarchical Polyaniline Spheres

Fabrication of two biomimetic superhydrophobic polymeric surfaces

A Novel Fabrication of A Superhydrophobic Surface with Highly Similar Hierarchical Structure of the Lotus Leaf on A Copper Sheet

Facile Fabrication of Superhydrophobic Coatings Based on Two Silica Sols

Fabrication of biomimetic superhydrophobic surface with controlled adhesion by electrodeposition

Controllable Fabrication of Lotus-Leaf-like Superhydrophobic Surface on Copper Foil by Self-Assembly

A One-Step Method to Fabricate Lotus Leaves-Like Zno Film

Flexible Superhydrophobic Film with Micro-Nano-ag Particles Fabricated by Spray Replacement

Fabrication of Superhydrophobic Surfaces of Cellulose Sheets by Creating Biomimic Structures

Packing the Silica Colloidal Crystal Beads: A Facile Route to Superhydrophobic Surfaces

Facile fabrication of flexible superhydrophobic surfaces with high durability and good mechanical strength through embedding silica nanoparticle into polymer substrate by spraying method

Fabrication of superhydrophobic coating via a facile and versatile method based on nanoparticle aggregates

Facile Formation of Hierarchical Textures for Flexible, Translucent, and Durable Superhydrophobic Film

An easy-to-implement method for fabricating superhydrophobic surfaces inspired by taro leaf

A Novel Approach To Stable Superhydrophobic Surfaces