Research on Frequency Locking of 1560 nm Fiber Laser Based on Rubidium Atomic Modulation Transfer Spectroscopy Technology
Yu Xiao,Lv Mengjie,Zhang Xu,Jia Aiai,Wang Guochao,Zhu Lingxiao,Yan Shuhua,Yang Jun
DOI: https://doi.org/10.3788/CJL202249.0301002
2022-01-01
Chinese Journal of Lasers
Abstract:Objective C-band (1530-1565 nm) lasers are widely used in the field of optical fiber communication because of their extremely low energy loss in optical fibers. In addition, fiber lasers have the advantages of narrow line width, small size and simple structure and have important application values in various fields such as optical sensing, lidar and quantum communications. These applications require a narrow laser linewidth and a stable laser frequency, especially under precise measurement conditions. The realisation of laser frequency stabilisation in this band is of great significance in spectroscopy and precision measurement. In addition to the frequency stabilisation of C-band lasers directly through molecular absorption lines such as acetylene (C2H2) , ammonia (NH3) and hydrogen cyanide (HCN), another method is to convert C-band lasers to visible-light bands and then use some classic atomic-transition spectral lines for frequency stabilisation. However, in the field of quantum precision measurement, commercial semiconductor lasers in the visible-light band are currently mainly used for quantum control. These seed light sources have a wide line width and generally require line width compression when used. By combining the C-band narrow line width laser technology with the frequency doubling and frequency technology of high conversion efficiency nonlinear crystals, high-power narrow-linewidth lasers with a variety of visible wavelengths can be realized, which is expected to replace semiconductor lasers in the fields of atomic and molecular physics and quantum information technology. Methods We investigated and compared the advantages and disadvantages of different frequency stabilisation methods and determined our experimental programme. Unlike previous reports that directly use a 780 nm semiconductor laser to stabilise the frequency and use a 1560 nm semiconductor laser to amplify and double the frequency, this study uses a 1560 nm narrow linewidth, Piezoelectric Transducer (PZT) cavity-tuning fiber laser as the seed light source, and after the frequency is doubled to the 780 nm band, modulation transfer spectroscopy (MTS) technology locks on the 3-4 cross peak of the rubidium atom (Rb-87) D2 line. The MTS module comprises two parts: a free-space frequency stabilisation optical path and a modulation and demodulation circuit. The frequency-multiplied 780 nm incident light is divided into two beams via a half glass and a polarisation splitting prism, which are used as the pump and a probe beams, respectively. After passing an electro-optic modulator ( EOM) driven by a modulated signal, the two light beams are incident to the Rb atomic absorption cell in the reverse direction, and the four-wave mixing effect occurs to obtain the saturated absorption spectrum signal with modulation. The absorption spectrum signal detected by the photodetector is demodulated into a frequency discriminator signal by the mixer and then output to the servo control circuit board (including the triangular wave scanning circuit and Proportion Integration Differentiation circuit) , and the bias voltage and peak voltage of the triangular wave are changed to further reduce noise. When the laser' s frequency scanning range meets the frequency-locking requirement, the modulation switch is toggled to realise the frequency locking of the laser. Results and Discussions First, we optimise the power ratio of the pump and probe beams and select 1. 3 as the optimal ratio of them(Fig. 3) . Then, for the optimisation of modulation and demodulation signals, we choose 12 MHz as the best modulation frequency [Fig. 4 ( a) ] and 10 V as the best demodulation peak-to-peak value [Fig. 4 ( b)]. Compared with the parameters of MTS signals when not optimized, the amplitude and slope of the optimised MTS signal increase considerably (Fig. 5) . Notably, 10 V is the maximum output peak-to-peak value of the existing signal generator and 12 MHz is the optimal resonance frequency of the self-made EOM, which enhances the MTS signal. Therefore, these two values are the optimal values obtained under the various constraints of the system. Finally, we beat the frequency-stabilised laser and the precisely locked optical frequency comb and calculate the Allan variance (Fig. 7). In our system, the peak-to-peak value of the frequency fluctuation after frequency stabilisation is 0.424 MHz and the standard deviation is 0. 0049 MHz [ Fig. 7 (a)]. When the integration time is 1 s, the Allan variance of the beat frequency is 3 x 10(-11), and when the integration time is 10 s, it is taken to the minimum value of 1.4 x 10(-11) [Fig.7(b)]. Conclusions This study investigates the MTS frequency stabilisation method based on 1560 nm laser frequency doubling, optimises the analysis of the modulation transfer signal and finally locks the 1560 nm fiber laser frequency doubling to the 3-4 cross peak of the rubidium atom D2 line. After the laser is frequency-locked, it beats with an optical frequency comb and the standard deviation of the beat frequency value after locking for 1 h is 0. 049. The Allan variance is used to characterise the performance of the system frequency locking, and the relative frequency stability after frequency locking reaches the minimum within the integration time of 10 s. The system results show that the 1560 nm fiber laser frequency locking system based on rubidium MTS can achieve excellent frequency stabilisation performance. Moreover, the frequency stabilisation system can output high-frequency stability at 1560 and 780 nm narrow-linewidth lasers simultaneously, which can be directly applied to fiber sensing, lidar and rubidium atoms as experimental media, quantum information, atomic and molecular physics and other fields.