Abstract:Objective: To investigate the influence of light and heavy bite force on the mandibular movement trajectories, and the influence of bite force on virtual occlusal pre-adjustment of digital full crown. Methods: From October 2021 to March 2022, 10 postgraduate volunteers (3 males and 7 females, aged 22-26 years) were recruited from Peking University School and Hospital of Stomatology. Maxillary and mandibular digital models of the participants were obtained by intraoral scanning. Jaw relations were digitally transferred under heavy bite force and mandibular movement trajectories under light and heavy bite force were recorded by jaw motion analyser. Three mandibular markers were chosen, namely the mesial proximal contact point of the central incisor (incisal point) and the mesial buccal cusp tips of the bilateral first molars. The three-dimensional displacements of the markers under two kinds of bite force in the intercuspal position (ICP), the sagittal projection of the three-dimensional displacements in the protrusive edge-to-edge position, and the coronal projection of the three-dimensional displacements in the lateral edge-to-edge position of upper and lower posterior teeth were measured. Single-sample t-test was used to compare the three-dimensional displacements and the corresponding sagittal projection and coronal projection with 0, respectively. The left maxillary central incisor and left mandibular first molar were virtually prepared by the reverse engineering software. Then dental design software was used to design digital full crown using the copy method. The mandibular movement trajectories under light and heavy bite force were separately used to guide virtual occlusal pre-adjustment. The three-dimensional deviations (mean deviations and root mean square) between the lingual surface of the left maxillary central incisor or the occlusal surface of the left mandibular first molar and that of the natural tooth before preparation were calculated (light bite force group and heavy bite force group), and the differences between the two groups were compared by the paired t-test. Results: Under the two kinds of bite force, the three-dimensional displacements of the markers in the ICP were (0.217±0.135), (0.210±0.133) and (0.237±0.101) mm, respectively; the sagittal projection of the three-dimensional displacements of the markers in the protrusive edge-to-edge position were (0.204±0.133), (0.288±0.148) and (0.292±0.136) mm, respectively; the coronal projection of the three-dimensional displacements of the mesial buccal cusp tips of the bilateral first molars in the lateral edge-to-edge position were (0.254±0.140) and (0.295±0.190) mm, respectively. The differences between the above displacements and 0 were statistically significant (P<0.05). The results of occlusal pre-adjustment showed that the mean deviations of the lingual surface of the left maxillary central incisor in the light and heavy bite force groups were (0.215±0.036) and (0.195±0.041) mm (t=3.95, P=0.004), respectively. The mean deviations of the occlusal surface of the left mandibular first molar were (0.144±0.084) and (0.100±0.096) mm (t=0.84, P=0.036), respectively. Conclusions: Both the light and heavy bite force have an influence on the mandibular movement trajectories. Virtual occlusal pre-adjustment of prostheses with mandibular movement trajectories under heavy bite force can obtain morphology of lingual or occlusal surfaces closer to the natural teeth before preparation.

[Investigation on the Relationship of Occlusal Force to Formation of Wedge-Shaped Defects].

Study of the relationship between facial anatomical marking points and occlusal vertical dimension

Study on the fracture-resistant forces of premolars with wedge-shaped defects post restoration

Occlusal Risk Factors Associated with Temporomandibular Disorders in Young Adults with Normal Occlusions.

Three-dimensional Finite Element Method Stress Analysis of First Mandibular Premolar with Various Degree of Wedge-shaped Defects under Loading

Temporomandibular joint stress analysis of patients with different mandibular deformities during unilateral molar occlusion

Two-dimensional finite element stress analysis of dental wedge-shaped defects in the elderly

Study on the correlation between the structure of TMJ and vertical craniofaciai pattern, occlusion in Class Ⅱ1 Children

Biomechanical Evaluation of the Mandibular First Molar After Simulated Occlusal Wear Using 3D Finite Element Analysis

[Study on mandibular movement trajectory and virtual occlusal pre-adjustment under light and heavy bite force].

Three-dimensional finite element analysis of unilateral mastication in malocclusion cases using cone-beam computed tomography and a motion capture system

Intensity of Singular Stress Field due to Wedge-Shaped Defect in Human Tooth after Restored with Composite Resins

Mandibular Stress and Its Relevance Analysis of Skeletal Open Bite and Deep Overbite Dysplasias by Finite Element Method

[Two-Dimensional Finite Element Stress Analysis of Simulating Restored Teeth with Wedge-Shaped Defects under Loads].

[A Study of Consistency of Occlusal Type with Skeletal Pattern and Integumental Profile].

Quantitative evaluation of the proximal contact area gap change characterization under intercuspal occlusion by intraoral 3D scanning: Food impaction with tight proximal contact

Morphological Design of Occlusal Wear Facets for the Mandibular First Molar Crown Using Different Bite Registration Methods.

Analysis of the Mandibular Position in Malocclusion Patients.

Analysis of Mandibular Position of Patients with Angles Class I and ClassII,Di Vision 1 Malocclusion

[Occlusal Force and Its Distribution in the Position of Maximum Intercuspation in Individual Normal Occlusion: a Cross-Sectional Study].

The Biomechanical Research on the Different Stress Distributions Between Complete and Defective Dentition