Abstract:Until now, lithium-ion battery production technology relied on a slurry-based process using organic solvents (NMP), which is hazardous and is a major contributor to high cost and energy consumption in battery manufacturing processes. Among many studies to reduce battery costs, the dry electrode process that does not use organic solvents is attracting attention as a rising star. Dry electrode technology is one of the most promising processes for next-generation energy storage systems due to their eco-friendly production and lowering energy costs (US$ kWh −1 ). However, when nano-sized carbon black (CB) is used in a dry electrode process, electrochemical performance deteriorates due to insufficient conductivity in the electrode due to pin-point contact with the nickel-rich cathode. In addition, when CNTs used in the conventional wet process are applied to a dry electrode process, it is still difficult to prepare a dry electrode that is uniformly distributed within the electrodes due to its very high aggregation properties. Despite having innovative advantages, solvent-free processing remains a challenge due to these critical issues. Here, we fabricated a dry-type electrode by using poly-crystalline Ni-rich cathodes uniformly coated with CNTs (Carbon nanotubes), resulting in higher electrical conductivity than the electrodes prepared with the conventional wet process including carbon black (CB). In addition, as a result of minimizing the amount of PTFE binder in the electrode by eliminating the mixing of existing carbon black (CB), dry electrode manufacturing was enabled without crushing the Ni-rich cathodes even the fabrication of dense cathodes with extremely high active material content (99.7%) and high electrode density (4.0 g cm -3 ). The CNT-coated dry electrodes show a high Q vol of ~860 mAh cm -3 at a current rate of 0.2 C (~1.0 mA cm -2 ) compared to the conventional wet-process electrodes (98 wt% Ni-rich cathode; ~3.6 g cm -3 ). Furthermore, to demonstrate the practical LiBs operation, a 12cm 2 -sized pouch cell (>60mAh) was fabricated via dry process and exhibited excellent cycle performance (up to 80% after 400 cycles). We believe that this solvent-free lithium-ion battery via carbon nanotube-coated Ni-rich cathodes approach would be feasible and bring a new electrode design paradigm to the lithium-ion battery market. Figure 1

Lithium-ion Batteries Based on Vertically-Aligned Carbon Nanotube Electrodes and Ionic Liquid Electrolytes.

Vertically Aligned Carbon Nanotube Electrodes for Lithium-Ion Batteries

Flexible and Stable Lithium Ion Batteries Based on Three-Dimensional Aligned Carbon Nanotube/silicon Hybrid Electrodes

Carbon Nanotube Array Anodes for High-Rate Li-ion Batteries

Depolarized and Fully Active Cathode Based on Li(Ni0.5co0.2mn0.3)O-2 Embedded in Carbon Nanotube Network for Advanced Batteries

Vertically Aligned N-doped Carbon Nanotubes Arrays as Efficient Binder-free Catalysts for Flexible Li-CO2 Batteries

Highly ordered carbon nanotubes to improve the conductivity of LiNi0.8Co0.15Al0.05O2 for Li-ion batteries

Synthesis and Electrochemical Performance of Vertical Carbon Nanotubes on Few-Layer Graphene As an Anode Material for Li-ion Batteries

Carbon-Coated Li3 VO4 Spheres As Constituents of an Advanced Anode Material for High-Rate Long-Life Lithium-Ion Batteries.

High Performance Electrochemical Capacitors from Aligned Carbon Nanotube Electrodes and Ionic Liquid Electrolytes

Solvent-Free Lithium-Ion Batteries to High Volumetric Capacity via Carbon Nanotube-Coated Ni-Rich Cathodes

Multidimensional VO2 nanotubes/Ti3C2 MXene composite for efficient electrochemical lithium/sodium-ion storage

High performance lithium ion battery anodes based on carbon nanotube-silicon core-shell nanowires with controlled morphology

Sputtered Nickel Oxide on Vertically-Aligned Multiwall Carbon Nanotube Arrays for Lithium-Ion Batteries

Carbon Nanotube Wiring of Electrodes for High-Rate Lithium Batteries Using an Imidazolium-Based Ionic Liquid Precursor As Dispersant and Binder: A Case Study on Iron Fluoride Nanoparticles

Dual Vertically Aligned Electrode‐Inspired High‐Capacity Lithium Batteries

Oxygenated Carbon Nitride-Based High-Energy-density Lithium-Metal Batteries

Filled Carbon Nanotubes as Anode Materials for Lithium-Ion Batteries

Double-Nanocarbon Synergistically Modified Na3V2(PO4)3: an Advanced Cathode for High-Rate and Long-Life Sodium-Ion Batteries.

Nanochannel-confined Synthesis of Nb2O5/CNTs Nanopeapods for Ultrastable Lithium Storage

Ti3C2 MXene Nanosheets/Vanadium Nitride@Carbon Composite Electrodes for High-Performance Lithium-Ion Batteries