Abstract:As the third generation solar cell,dye-sensitized solar cells (DSSCs) have attracted tremendous amount of interest in scientific research and industrial applications during the past 25 years because of their simple production procedures,low-cost,environmental friendliness of raw materials,and relatively high power conversion efficiency (PCE).As an important component,counter electrode (CE) not only transfers electrons flowing from the external circuit to the electrolyte,but also catalyzes the reduction of oxidized electrolyte at the CE/electrolyte interface.So far,Pt as a noble metal has been the most commonly used CE for laboratory research due to its excellent electrocatalytic activity,high conductivity and good chemical stability.Unfortunately,the high cost and low abundance ratio of Pt create a big obstacle for large-scale applications of DSSCs.Therefore,exploiting Pt-free CE materials with high electrocatalytic activity and low cost is vital for the practical applications.Recently,a lot of Pt-free materials,such as graphene,carbon,conductive polymers and metal compounds (including carbide,oxide,sulfide,nitride and selenide),have been proposed for use as the CE of DSSCs.Among those materials,metal selenides have drawn great interest due to their distinctive electronic structures,interesting chemical behaviors and distinctive physical properties.The electrocatalytic activity of a substance not only depends on the chemical composition but also relies on the morphology of materials.While the investigation on developing new electrocatalysts has been extensively conducted,the morphology effect on the electrocatalytic activity has rarely been studied.In this paper,a simple low temperature hydrothermal method was used to synthesize NiSe2 with nanorod (r-NiSe2) and nanoparticle (p-NiSe2) morphologies.A drop-cast method was used to fabricate CE films without any post-treatment.Since the only difference for those two CEs used in DSSC is their morphology,it allows us to study the morphology effect on the electrocatalytic activity and solar cell performances.By changing the drop-cast times,the loading amount from 5.0 to 80.0 μg/cm2 could be controlled.The PCE of DSSCs increases with increasing the loading amount up to 10 μg/cm2 and then decreases with further increasing the loading amount of NiSe2.Thus,the best loading amount has been determined to be 10 μg/cm2.All the measurements in this paper are based on the best loading amount.The DSSC with r-NiSe2 CE achieves PCE of 8.52％,which is higher than that for the p-NiSe2 based DSSC (8.13％) and even better than the Pt based DSSC (8.20％) at comparable conditions.This indicates that NiSe2 nanorod is better than NiSe2 nanoparticle as the CE of DSSCs towards higher photovoltaic performance.To elucidate the catalytic activity of r-NiSe2 and p-NiSe2,electrochemical impedance spectroscopy,Tafel polarization curve and cyclic voltammetry were conducted.The experimental results indicate that the r-NiSe2 CE exhibits higher electrocatalytic activity than p-NiSe2 CE,which explains the reason that the DSSC based on r-NiSe2 CE has the higher PCE than the p-NiSe2 CE.The result implies that by varying the morphologies of CE materials could also fulfill the improvement of solar cell's performance.

In Situ Growth of Co0.85se and Ni0.85se on Conductive Substrates As High-Performance Counter Electrodes for Dye-Sensitized Solar Cells

Facile Synthesis of Nitrogen-Doped Reduced Graphene Oxide As an Efficient Counter Electrode for Dye-Sensitized Solar Cells

Efficient Electrocatalysts for Dye-Sensitized Solar Cells

In situ direct growth of single crystalline metal (Co, Ni) selenium nanosheets on metal fibers as counter electrodes toward low-cost, high-performance fiber-shaped dye-sensitized solar cells.

Development of binary transition metallic selenide (NiSe/Co3Se4) hybrid counter electrode for highly efficient Pt-free dye-sensitized solar cells

CoSe2@N-Doped Graphene Nanocomposite High-Efficiency Counter Electrode for Dye-Sensitized Solar Cells

One-step electrodeposited CoSe2 nano-reticular with high electroconductivity and electrocatalytic as a counter electrode for dye sensitized solar cell

In Situ Electrodeposition of Nickel Cobalt Selenides on FTO As an Efficient Counter Electrode for Dye-Sensitized Solar Cells

Metal Selenides as Efficient Counter Electrodes for Dye-Sensitized Solar Cells.

High Catalytic Activity and Stability of Nickel Sulfide and Cobalt Sulfide Hierarchical Nanospheres on the Counter Electrodes for Dye-Sensitized Solar Cells

Electrodeposition of nanostructured cobalt selenide films towards high performance counter electrodes in dye-sensitized solar cells

CoSe2/N-Doped Carbon Hybrid Derived from ZIF-67 As High-Efficiency Counter Electrode for Dye-Sensitized Solar Cells

Co9Se8 Nanosheets Electrodes: Drop‐Cast versus in situ Growth

Plasma-modified SnO2:F Substrate for Efficient Cobalt Selenide Counter in Dye Sensitized Solar Cell

Synthesis of Nise2/Reduced Graphene Oxide Crystalline Materials and Their Efficient Electrocatalytic Activity in Dye-Sensitized Solar Cells

Boosting Catalytic Performance of Hierarchical Co/Co0.85Se Microspheres Via Mott-Schottky Effect Toward Triiodide Reduction and Alkaline Hydrogen Evolution

Single-crystal Cobalt Selenide Nanobelt As a Highly Efficient Cathode for Stable Quasi-Solid-state Dye Sensitized Solar Cell

One-Step Electrochemical Deposition of Hierarchical Cus Nanostructures on Conductive Substrates As Robust, High-Performance Counter Electrodes for Quantum-Dot-Sensitized Solar Cells

Highly Efficient Dye-Sensitized Solar Cells with NiSe2 Counter Electrodes: Effect of Morphology on the Electrocatalytic Activity and the Photovoltaic Performance

In Situ Synthesis of Oriented NiS Nanotube Arrays on FTO As High-Performance Counter Electrode for Dye-Sensitized Solar Cells

Nickel Sulfide Counter Electrodes Enhanced by Hydrosulphuric Acid Hydrothermal Treatments for Use in Pt-free Dye-Sensitized Solar Cells