Abstract:A composite titania thin film consisted of quasi-aligned single-crystalline rutile nanorods embedded in sol-gel-derived anatase aggregates was fabricated and its photoelectrochemical behavior was studied in detail. A monolayer of nearly sing I e-crystal line rutile nanorods was first deposited on metallic Ti substrates through a controlled reaction between Ti and hydrogen peroxide. The gaps among the rutile nanorods were then filled with titania nanoparticles through a sol-gel dip-coating approach, which achieved a composite thin film of single-crystalline rutile nanorods embedded in anatase aggregates, after a subsequent thermal treatment at 723 K. The X-ray diffraction measurement revealed that the composite film with thickness of 180 nm contained anatase and rutile in a nearly 50:50 ratio. The UV-visible diffusive reflectance spectra estimated a band gap of 2.99 eV for the rutile monolayer and a slightly increased value of 3.03 eV for the composite film due to the embedding of the anatase nanoparticles. Photocurrent versus potential diagrams, photocurrent transient curves, and open-circuit potential measurement supported the fact that the anatase nanoparticles possessed better inherent photoelectrochemical properties than rutile. However, electrochemical impedance spectra characterization, together with photocurrent transient curves and open-circuit potential measurement, suggests that the single-crystalline rutile nanorods exhibited a higher electron-transfer rate. The combination of the two components in such an appropriate way enhanced significantly the charge separation effect arising from the anatase/rutile couple, which hence combined efficiently the "mixed crystal effect" and the "mixed morphological effect". A steady-state photocurrent more than double the simple sum of those generated by the two components alone was detected for the current composite film, which can be attributed to the single-crystalline rutile nanorods that provide channels for rapid electron transfer to the conductive Ti substrates under an applied bias potential. As a result, this study concludes that the present nanostructure magnified significantly the well-established mixed crystal effect, that is, an enhanced charge separation arising from a mixture of anatase and rutile.

Enhancement of Hole Mobility of Poly(3‐hexylthiophene) Induced by Titania Nanorods in Composite Films

Improving poly(3-hexylthiophene)-TiO2 heterojunction solar cells by connecting polypyrrole to the TiO2 nanorods

The Influence of Amino Group on PCDTBT-based and P3HT-based Polymer Solar Cells: Hole Trapping Processes

Charge Transport Properties of Low Temperature Solution Processable Poly(3-Hexylthiophene)/Surface Modified Tio2 Bulk Heterojunction Systems

Structural and optoelectronic properties of P3HT-graphene composites prepared by in situ oxidative polymerization

Enhanced Photoelectrochemical Response of a Composite Titania Thin Film with Single-Crystalline Rutile Nanorods Embedded in Anatase Aggregates

Enhanced Electrochromic Properties of Donor–acceptor Polymers Via TiO2 Composite

Interplay of Three-Dimensional Morphologies and Photocarrier Dynamics of Polymer/TiO2 Bulk Heterojunction Solar Cells

Using Scanning Probe Microscopy to Study the Effect of Molecular Weight of Poly(3-Hexylthiophene) on the Performance of Poly(3-Hexylthiophene):Tio2 Nanorod Photovoltaic Devices

Hybrid poly (3-hexylthiophene)/titanium dioxide nanorods material for solar cell applications

Conjugated Polymer Controlled Morphology and Charge Transport of Small-Molecule Organic Semiconductors

Interfacial nanostructuring on the performance of polymer/TiO2 nanorod bulk heterojunction solar cells.

Hybrid Solar Cells Based on Blends of Poly(3-Hexylthiophene) and Surface Dye-Modified, Ultrathin Linear- and Branched-Tio2 Nanorods

Solid‐State NMR Exploration of Factors for Enhancement of Hole Mobility by Introduction of Poly(styrene) Into Poly(3‐hexylthiophene)

Employing an Amphiphilic Interfacial Modifier to Enhance the Performance of A Poly(3-Hexyl Thiophene)/Tio2 Hybrid Solar Cell

Improved Charge Separation and Transport Efficiency in Poly(3-Hexylthiophene)-Tio2 Nanorod Bulk Heterojunction Solar Cells

Synergistic Effect between NiOx and P3HT Enabling Efficient and Stable Hole Transport Pathways for Regular Perovskite Photovoltaics

Tuning Hole Transport Properties Via Pyrrole Derivation for High‐Performance Perovskite Solar Cells

Improving the hole transport performance of perovskite solar cells through adjusting the mobility of the as-synthesized conjugated polymer

Enhanced Hole Mobility of p-Type Materials by Molecular Engineering for Efficient Perovskite Solar Cells

Molecular engineering of novel dithiophene-fused hole-transporting materials for highly efficient perovskite solar cells