Determination of opening velocities for vacuum circuit breakers at transmission voltage
Xiaofei Yao,Jianhua Wang,Yingsan Geng,Zhiyuan Liu,Xiaoshe Zhai
DOI: https://doi.org/10.1109/DEIV.2016.7748703
2016-01-01
Abstract:The objective of this paper is to propose a quantitative method to determine opening velocities for VCBs at transmission voltage. A couple of 2/3 coil-type axial magnetic field (AMF) contacts, which are used in a 126 kV vacuum interrupter, are arranged in a demountable vacuum chamber. The movable contact is opening with three different kinds of opening travel-curves. Each curve is adjusted by two opening velocities, v
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1</inf>
and v
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</inf>
, respectively. The v
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1</inf>
is an average opening velocity within 1/3 full contact gap, which is with 1.8 m/s, 2.4 m/s and 2.7 m/s, respectively. The v
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</inf>
is an average opening velocity within 2/3 full contact gap, which is with 2.4 m/s, 2.7 m/s, and 3.0 m/s, respectively. The test current ranges from 4 kA to 40 kA, stepped by 4 kA. When a VCB is used to interrupt a short-circuit current, the preferred opening velocity is determined by reducing the arcing interval t
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">I</inf>
for the intense arc mode and increasing the arcing interval t
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">II</inf>
until the formation of high-current anode mode (HAM). The preferred v
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1</inf>
is higher than a threshold value v
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1_th</inf>
, at which there is a peak critical contact gap d
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">I_peak</inf>
, for the evolving from intense arc mode into diffuse arc mode. The preferred value v
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</inf>
is lower than another threshold value v
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2_th</inf>
, at which there also exists a peak critical contact gap d
<inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">II_peak</inf>
, for the evolving from diffuse arc mode into the footpoint mode and anode spot mode.