Abstract:Zn metal anodes in aqueous electrolytes suffer from interface issues including uncontrolled dendrite growth and undesired side reactions, resulting in their limited application in terms of short circuits and cell failure. Herein, a hybrid interface chemistry strategy is developed through ultrafast microwave polarization at the skin region of bare Zn. Owing to efficient Joule heating directed by abundant local hot spots at electron valleys, the rapid establishment of a dense interfacial layer can be realized within a minute. Stabilized Zn with suppressed side reactions or surface corrosion is therefore achieved due to the interfacial protection. Importantly, hybrid zincophilic sites involving laterally/vertically interconnected Cu-Zn intermetallic compound and Zn2+-conductive oxide species ensure mixed charge conducting (denoted as CuHL@Zn), featuring uniformly distributed electric field and boosted Zn2+ diffusion kinetics. As a consequence, CuHL@Zn in symmetric cells affords lifespans of 2800 and 3200 h with ultra-low polarization voltages (approximate to 19 and 56 mV) at a plating capacity of 1.0 mAh cm-2 for 1 and 5 mA cm-2, respectively. The CuHL@Zn||MnO2 full cell further exhibits cycling stability with a capacity retention of over 80% for 500 cycles at 2 A g-1. A hybrid interfacial layer is in situ constructed at the surface of Zn via a microwave polarization strategy. Interconnected zincophilic sites concerning metallic Cu5Zn8 alloy and Zn2+-conductive ZnO ensure mixed charge conducting for regulated Zn nucleation and deposition behavior, contributing to dendrite-free Zn anode with promote stability and reversibility. image

Zn As the Protective Layer for Cu Electrode in Wafer-Si Solar Cells

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Assembly of Metal–Organic Chemical Conversion Layers As Ion Sieves along with Exposing Zn(002) Planes for Stable Zn Metal Anode

Stabilizing Zn Metal Anode by Interfacial Self-Assembled Zincophilic Metal-Organic Complex Conversion Layers

Enhancing Adhesion and Reducing Ohmic Contact through Nickel–Silicon Alloy Seed Layer in Electroplating Ni/Cu/Ag

Hybrid Interface Chemistry Enabling Mixed Conducting Via Ultrafast Microwave Polarization Toward Dendrite-Free Zn Anodes

A zincophilic interface coating for the suppression of dendrite growth in zinc anodes

A Cu-Ag Double-Layer Coating Strategy for Stable and Reversible Zn Metal Anodes

Copper Hexacyanoferrate Solid‐State Electrolyte Protection Layer on Zn Metal Anode for High‐Performance Aqueous Zinc‐Ion Batteries

Ag and Sn capping layers for stabilizing Cu solar cell contacts against oxidation in air: effects of method and solution of deposition

Achieving the dendrite-free zinc anode by constructing a Sn-C interfacial layer with zincophilic and conductive network

Constructing a well-wettable interface on a three-dimensional copper foam host with reinforced copper nanowires to stabilize zinc metal anodes

Multicomponent Copper-Zinc Alloy Layer Enabling Ultra-Stable Zinc Metal Anode of Aqueous Zn-ion Battery.

Alloying strategy to stabilize monocrystalline zinc anode under high utilization and working capacity

Galvanically replaced artificial interfacial layer for highly reversible zinc metal anodes

Formation of Alloyed Cu 2 Co x Zn 1- x Sn(S,Se) 4 Absorption Layer and Its Application in Solar Cells

Large‐Scale Integration of Zinc Metasilicate Interface Layer Guiding Well‐Regulated Zn Deposition

Mitigating Zn Dendrite Growth and Enhancing the Utilization of Zn Electrode in Aqueous Zn-Ion Batteries

Layer-by-layer zinc metal anodes to achieve long-life zinc-ion batteries