Abstract:Many sensors exhibit output impedances greater than a few MΩ, and the subsequent instrumentation amplifier (IA) must be carefully designed to meet the requirements of high input impedance $(\mathrm{R}_{\text{in}})$ , low noise and low offset. Chopping is a power-efficient technique to achieve low offset and low 1/f noise without noise aliasing [1]–[4], but at the expense of a lower $\mathrm{R}_{\text{in}}$ (10–100MΩ [1] [4] [5]). Positive feedback loop (PFL) can boost $\mathrm{R}_{\text{in}}$ of a capacitively-coupled chopper IA (CCIA) by providing a large portion of input source current [4]. However, in practice, the PFL is not suitable for a generic chopper amplifier to achieve a high $\mathrm{R}_{\text{in}}$ above $100\text{MO}$ , because the actual impedance boosting factor highly depends on the absolute accuracy of the feedback elements and the overall gain of the IA. For instance, to compensate input parasitic capacitance of 100fF by the PFL, an IA with a voltage gain of 100 requires a very small feedback capacitor of 1fF. Meanwhile, this feedback capacitor must be reconfigured with different IA gains. For the same reason, the PFL is not applicable to a chopper operational amplifier (OPA) either due to its ill-defined open-loop gain. Apart from the limited $\mathrm{R}_{\text{in}}$ , chopper amplifiers also suffer from output ripple, i.e. the up-modulated offset. Prior art ripple reduction loop (RRL) can realize a sub-µV residual input referred ripple [1] [3], but this often involves an active loop integrator with large DC gain and time constant, resulting in power and area overhead.

A Low Power and Low 1/f Noise Chopper-Stabilized Amplifier with Current Recycling Technology

System Design of a Low Noise, Low Offset Instrumentation Amplifier with Chopper Stabilization

Compact 50-62 GHz Current-Reused Low-Noise Amplifier with Gate-Drain Transformer Feedback

A Low-Noise Low-Voltage Low-Power Bulk-Driven Amplifier with Chopper Stabilization Technique

A 36nv/√hz Noise PSD Chopper-Stabilized CMOS Amplifier with a New Ripple-Spur-filter Scheme

A 0.061-Mm² 1–11-Ghz Noise-Canceling Low-Noise Amplifier Employing Active Feedforward with Simultaneous Current and Noise Reduction

A Compact 2.1–39 GHz Self-Biased Low-Noise Amplifier in 65 Nm CMOS Technology

Ultralow Power E-Band Low-Noise Amplifier with Three-Stacked Current-Sharing Amplification Stages in 28-Nm CMOS

Design of Low Noise and Low Power Chopper Stabilized Amplifier for Neural Recording Applications

A 24-Ghz Voltage-Combined Stacked Power Amplifier with Current-Sharing Technique in 65-Nm CMOS

A Low Noise Operational Amplifier Design Using Chopper Stability

3.10 A 0.69/0.58-PEF 1.6nW/24nW Capacitively Coupled Chopper Instrumentation Amplifier with an Input-Boosted First Stage in 22nm/180nm CMOS.

Analysis and design of instrumentation amplifier based on chopper technology

A 2.8 Nv/√ Hz Chopper Amplifier for Bridge Readout with Dual Ripple Reduction and Noise- Nonlinearity -Cancelling Loop.

A 300kHz Bandwidth 1.66nV/√Hz Chopper Instrumentation Amplifier with Ripple Reduction Loop Using Multi-Rate Duty-Cycled Resistors

A 0.8V Chopper Amplifier with 600mvpp Tolerance to Power-Line Interference for Neural Signal Acquisition

A Low Power Current Recycling Constant-GM Rail-to-rail OTA

A 1.8Gω-Input-impedance 0.15Μv-Input-referred-ripple Chopper Amplifier with Local Positive Feedback and SAR-Assisted Ripple Reduction

Design of a 3.24μW, 39nV/√Hz chopper amplifier with 5.5Hz noise corner frequency for invasive neural signal acquisition

Measurement and Analysis of Current Noise in Chopper Amplifiers.

A low power constant-Gm rail-to-rail operational transconductance amplifier by recycling current