Abstract:Sn-Sb alloys are potential solders for replacement of high-Pb solders because of their high melting temperature in lead-free solders. However, Cu substrate is extremely dissolved by the Sn-Sb binary alloy during the high temperature soldering process, which will cause serious reliability problem of the solder joint. Based on this critical issue, we designed a new high temperature lead-free Sn-10Sn-5Cu ternary solder to prevent the dissolution of Cu substrate. In this study, liquid-state interfacial reaction between the high temperature lead-free solder and the Cu substrate was investigated. The liquid-state interfacial reaction of the solder on the Cu substrate was carried out at the different temperature of 280degC, 320degC,360degC and 400degC, and the reaction time was 1min, 10mins, 30mins and 60mins, respectively. Microstructure of the Sn-Sb-Cu bulk solder and the solder joint was observed by scattered electron microscope (SEM). The identification of phase composition was determined by Energy Dispersive X-ray Detector (EDX) and electron probe microscopy analysis (EPMA). During the four reaction temperatures, the interfacial reaction products included a scallop Cu6Sn5 intermetallic compound (IMC) layer and a flat Cu3Sn layer adjacent to Cu substrate. IMCs thickness with the reaction time was measured by the area of interface IMCs layer divided by the interface length. The IMCs thickness increased with the reaction temperature and reaction time, and the relationship between IMC thickness and reaction time was linear with square root of time, which signified that the IMC growth dynamics was diffusion controlled. The diffusion coefficient was calculated by the IMC growth rate, which increased with the higher temperature, corresponding to be 2.30 times 10-14, 6.84 times 10-14, 1.63 times 10-13, 1.99 times 10-13 m2/s for the temperatures of 280degC, 320degC, 360degC and 400degC, res- - pectively. And then the diffusion activation energy was determined to be 57.8 KJ/mol by fitting the four diffusion coefficients at various temperatures, which indicated that the diffusion mechanism was grain boundary diffusion. Between lower temperature of 280degC and higher temperature of 400degC, huge differences existed on the microstructure of IMC in the interior solder of the solder joint.

Mechanical Properties and Microstructure of Sn-based Solder Joints at Cryogenic Temperature

Mechanical Properties and Microstructure of Mixed SnAgCu-SnPb Solder Joints at Cryogenic Temperature

Fracture pattern evolution of SnAgCu–SnPb mixed solder joints at cryogenic temperature

Experimental and Statistical Study of the Fracture Mechanism of Sn96.5Ag3Cu0.5 Solder Joints via Ball Shear Test

Ductile-to-brittle transition in fracture behaviors of common solder alloys over a temperature range down to −150 °C

Mechanical Response of Cu/Sn58Bi-xNi/Cu Micro Solder Joint with High Temperatures

Microstructure evolution and mechanical properties of Sn-9Zn-2.5Bi-1.5In solder joints with aging treatment under various conditions

Microstructure Evolution Of Solder Joints With Different Pb Contents At Ultra-Low Temperature

Microstructural evolution of Sn-9Zn-3Bi and Sn-9Zn-3Bi-0.3Cr solder under high-temperature and high-humidity conditions

Study on the Microstructure Evolution and Mechanical Properties of Cu/Cu41Sn11/Cu Solder Joint During High-Temperature Aging

Microstructure evolution and mechanical properties of copper/304 stainless-steel joints by low-temperature soldering

Effects of aging time and temperature on shear properties of Sn–Zn and Sn–Ag–Cu solder joints

Microstructure and Shear Strength of Sn37Pb/Cu Solder Joints Subjected to Isothermal Aging

The microstructure evolution and failure mechanism of Sn37Pb solder joints under the coupling effects of extreme temperature variation and electromigration

Microstructural Evolution and Mechanical Properties of Sn‐58Bi Solder Alloys with Different Cooling

Comparison of high-speed shear properties of low-temperature Sn-Bi/Cu and Sn-In/Cu solder joints

Tensile Properties of Cu/Sn–58Bi/Cu Soldered Joints Subjected to Isothermal Aging

Phase Transformations and Mechanical Properties in In–Bi–Sn Alloys as a Result of Low-Temperature Storage

Interfacial reaction and mechanical properties of Sn–Bi Cu core solder joints

Liquid-state interfacial reaction of Sn-10Sb-5Cu high temperature lead-free solder and Cu substrate

Microstructure and mechanical properties of Cu joints soldered with a Sn-based composite solder, reinforced by metal foam