Abstract:Modern computerized planning tools for periacetabular osteotomy (PAO) use either morphology-based or biomechanics-based methods. The latter relies on estimation of peak contact pressures and contact areas using either patient specific or constant thickness cartilage models. We performed a finite element analysis investigating the optimal reorientation of the acetabulum in PAO surgery based on simulated joint contact pressures and contact areas using patient specific cartilage model. Furthermore we investigated the influences of using patient specific cartilage model or constant thickness cartilage model on the biomechanical simulation results. Ten specimens with hip dysplasia were used in this study. Image data were available from CT arthrography studies. Bone models were reconstructed. Mesh models for the patient specific cartilage were defined and subsequently loaded under previously reported boundary and loading conditions. Peak contact pressures and contact areas were estimated in the original position. Afterwards we used a validated preoperative planning software to change the acetabular inclination by an increment of 5° and measured the lateral center edge angle (LCE) at each reorientation position. The position with the largest contact area and the lowest peak contact pressure was defined as the optimal position. In order to investigate the influence of using patient specific cartilage model or constant thickness cartilage model on the biomechanical simulation results, the same procedure was repeated with the same bone models but with a cartilage mesh of constant thickness. Comparison of the peak contact pressures and the contact areas between these two different cartilage models showed that good correlation between these two cartilage models for peak contact pressures (r = 0.634 ∈ [0.6, 0.8], p < 0.001) and contact areas (r = 0.872 > 0.8, p < 0.001). For both cartilage models, the largest contact areas and the lowest peak pressures were found at the same position. Our study is the first study comparing peak contact pressures and contact areas between patient specific and constant thickness cartilage models during PAO planning. Good correlation for these two models was detected. Computer assisted planning with FE modeling using constant thickness cartilage models might be a promising PAO planning tool when a conventional CT is available.

Computer Assisted Planning and Navigation of Periacetabular Osteotomy with Range of Motion Optimization

Computer Assisted Planning, Simulation and Navigation of Periacetabular Osteotomy.

Preoperative Planning Of Periacetabular Osteotomy (Pao)

Cadaveric Validation of a Novel Planning and Navigation System for Peri-Acetabular Osteotomy (PAO).

Computer-Assisted Optimization of the Acetabular Rotation in Periacetabular Osteotomy Using Patient's Anatomy-Specific Finite Element Analysis

Biomechanical Optimization-Based Planning of Periacetabular Osteotomy.

A Cost-Effective Surgical Navigation Solution for Periacetabular Osteotomy (PAO) Surgery

Periacetabular Osteotomy Through the Pararectus Approach: Technical Feasibility and Control of Fragment Mobility by a Validated Surgical Navigation System in a Cadaver Experiment

Three-dimensional acetabular reorientation during periacetabular osteotomy: an intraoperative navigation method using an external fixator for periacetabular osteotomy

Development of a Novel Customized Cutting and Rotating Template for Bernese Periacetabular Osteotomy.

A Cost-Effective Navigation System for Peri-acetabular Osteotomy Surgery.

Application of a 3-dimensional printed navigation template in Bernese periacetabular osteotomies: A cadaveric study

Periacetabular osteotomy using computed tomography-based navigation: preoperative planning and accuracy evaluation

Augmented Marker Tracking for Peri-acetabular Osteotomy Surgery: A Cadaver Study

Fast and Automatic Periacetabular Osteotomy Fragment Pose Estimation Using Intraoperatively Implanted Fiducials and Single-View Fluoroscopy

Robot-Assisted Augmented Reality (AR)-Guided Surgical Navigation for Periacetabular Osteotomy

Optimization Technique and Fe Simulation for Lag Screw Placement in Anterior Column of the Acetabulum

Use of 3D Printed Models to Determine Accurate Bone Cuts during a Periacetabular Osteotomy for Developmental Hip Dysplasia

Evaluation of Constant Thickness Cartilage Models Vs. Patient Specific Cartilage Models for an Optimized Computer-Assisted Planning of Periacetabular Osteotomy

[Study on Finite Element Analysis Method for the Pre-operative Planning of Bernese Periacetabular Osteotomy].

Development and evaluation of an image-free computer-assisted impingement detection technique for total hip arthroplasty