Abstract:Compression plates are widely used in orthopaedic surgeries for internal fixation of fractured femurs. To fix the plate and thus to provide compression to a fracture, the self-tapping bone screws are tightened through predrilled pilot holes of smaller diameter. Preliminary investigation showed that the holes drilled with the inappropriate cutting parameters cause mechanical and thermal damages to the local host bone, which further lead to loosening of internal fixations. In this paper, the mechanistic models to predict the thrust forces and torques during bone drilling were developed, using a 3.20 mm diameter drill bit. As a procedure, the cutting action was investigated at three different regions of the drill point, namely cutting lips, secondary cutting edges and indentation zone. The models employed the analytical approach to account for the drill-bit geometry and cutting parameters, and an empirical approach to account for the material and friction properties. To complete the procedure, calibration experiments were conducted on bovine cortical femurs with two different spindle speeds (1000 and 3000 r/min) and feeds (0.03 and 0.06 mm/rev), and then the specific normal and friction coefficients were determined. The developed mechanistic models were validated with different ranges of parameters (500–3500 r/min speeds, and 0.02–0.07 mm/rev feeds) those commonly involved in manual and robot-assisted surgery. The validation study revealed that the thrust forces predicted using the mechanistic models showed a maximum error of only 5.80%. However, the torques predicted from the mechanistic model found with more error than the thrust forces. The predominant reasons for this under-prediction might because of the extrapolation used to determine the specific cutting pressures, slip-line field applied to the indentation zone instead of compressive fracture, and chip clogging involved during the bone drilling as demonstrated in earlier studies. Despite the deviations, the developed mechanistic models satisfactorily follow the trends of the thrust forces and torques experienced during bone drilling. The outcomes can be used to practice the bone drilling procedure and monitor the effect of process parameters on thrust forces and torques in the in-silico environment before performing actual surgery.

Model-based State Recognition of Bone Drilling with Robotic Orthopedic Surgery System.

Model-Based Compensation of Moving Tissue for State Recognition in Robotic-Assisted Pedicle Drilling

A CT Image-Based Virtual Sensing Method to Estimate Bone Drilling Force for Surgical Robots.

Safety Analysis and Control of A Robotic Spinal Surgical System

Force-Position Hybrid Compensation Control for Path Deviation in Robot-Assisted Bone Drilling

State Recognition of Bone Drilling Based on Acoustic Emission in Pedicle Screw Operation

Force Perception and Bone Recognition of Vertebral Lamina Milling by Robot-Assisted Ultrasonic Bone Scalpel Based on Backpropagation Neural Network

Vibration Reduction, Characterization of Drill bit and Femur Bone to Forces During Robotic-Assisted Drilling Using Model Soft Fixture Embedded with Pressurized-Air Damper

A Cutter Vibration Signal Processing Based State Monitoring Method for Improving Operation Safety of Spinal Automatic Drilling System

Compact Bone Surgery Robot With a High-Resolution and High-Rigidity Remote Center of Motion Mechanism

Mechanistic models to predict thrust force and torque in bone drilling: An in-vitro study validated with robot-assisted surgical drilling parameters

Intraoperative control for robotic spinal surgical system with audio and torque sensing

Bone Layer Proportion Recognition and Cutting Depth Control Based on Intraoperative Signal Processing in Robotic Laminectomy

State recognition of decompressive laminectomy with multiple information in robot-assisted surgery

Model Experimental Study of Man-Machine Interactive Robot-Assisted Craniotomy

A cortical bone milling force model based on orthogonal cutting distribution method

A Biomechanics-Aware Robot-Assisted Steerable Drilling Framework for Minimally Invasive Spinal Fixation Procedures

An integrated system for planning, navigation and robotic assistance for skull base surgery

Milling State Identification Based On Vibration Sense Of A Robotic Surgical System

An End-to-End Inclination State Monitoring Method for Collaborative Robotic Drilling Based on Resnet Neural Network

Experimental Measurement of Force, Torque Control and Vibration Absorber System for Intraoperative Tele-Operated Robotic-Assisted Femoral Shaft Drilling Using Air-Controlled Soft Balloon Damper