Abstract:Wake-up receivers (WuRXs) help to significantly reduce the average power of the Internet of the Things (loT) hardware systems. To lower the “asleep” power in the idle state, the WuRX structures based on non-standard protocols have been widely studied in prior researches, which can realize a high sensitivity [1] or low power [2]. Compared to the non-standard receivers, there are more design challenges in the standard-compliant WuRXs. For example, a BLE-compliant WuRX operating in the congested 2.4GHz band should be able to handle potentially large interferers including adjacent-channel tone and image, as well as realize a high sensitivity for long-reach access. Therefore, there have been several conventional solutions for the interference-resilient BLE-compliant WuRXs: 1) Single-path down-conversion WuRXs. The interference is handled by an RF filter [3] or a low-noise LO [4] (Fig. 1, top). The WuRX in [3] utilized an FBAR filter to reject the interference from the adjacent channel, resulting in a signal-to-interference ratio (SIR) of −6dB@2MHz, where the loss of FBAR filter degraded the sensitivity to −85dBm. An LC oscillator based LO was adopted in [4] to suppress the adjacent-channel interference by −10dB, but it's at the penalty of 1.2mW power. 2) I/Q-path down-conversion WuRXs. A Hartley WuRX was designed in [5] to reject both 2MHz adjacent-channel interference and image (Fig. 1, middle), as well as improve the sensitivity to −92dBm, while the I/Q downconverters and LO generators dominated the total power consumption. Although the WuRX power was reduced to 352μW by the edge combiner based I/O LO generation, the SIR was limited to −12.5dB due to the spurs and noise accompanying the LO signal. As a result, it's difficult for the conventional WuRX structures to realize both a high SIR and low power consumption.

Towards Zero-Time Wakeup of Line Cards in Power-Aware Routers

Toward Power-Efficient Backbone Routers

On the Design of Green Reconfigurable Router Toward Energy Efficient Internet.

Green Router: Power-Efficient Router Design

Reducing Power of Traffic Manager in Routers Via Dynamic On/off-Chip Scheduling

GreenRouter: Reducing Power by Innovating Router's Architecture.

Low Power Architecture for High Speed Packet Classification

Energy Efficient Design for Multi-Shelf IP over WDM Networks

Power-proportional Router: Architectural Design and Experimental Evaluation

A Software-Defined Always-On System With 57-75-nW Wake-Up Function Using Asynchronous Clock-Free Pipelined Event-Driven Architecture and Time-Shielding Level-Crossing ADC

F-Bypass: a low-power network-on-chip design utilizing bypass to improve network connectivity

An Interference-Resilient 120-Degree-apart Pseudo-I/Q BLE-Compliant Wake-Up Receiver Achieving-21dB SIR,-94dBm Sensitivity, and 4-D Wake-Up Signature

A Unified Clock-Gated Error Correction Scheme with Three-Phase Latch-Based Pipeline for Energy-Efficient Wide Supply Voltage Range Router

Applying SMART-Based Power Gating Approach in NoC System

A Loading-Aware TDMA Sleep Scheme to Improve Power Consumption Performance on Medium to High Traffic for NG-EPON Networks

Energy-Efficient Scheme For Ieee 802.15.4 Compliant Device

Improved Opportunistic Sleeping Algorithms for LAN Switches

Robust Energy-Aware Routing With Uncertain Traffic Demands

Deadline-Aware Routing: An Energy Saving Scheme In Data Center Network

Low Latency Router Design Supporting both Deterministic Routing and Adaptive Routing

20.2 A 57nw Software-Defined Always-On Wake-Up Chip for IoT Devices with Asynchronous Pipelined Event-Driven Architecture and Time-Shielding Level-Crossing ADC