Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

Tunable Fabry-Perot Filter Using Hollow-Core Photonic Bandgap Fiber and Micro-Fiber for a Narrow-Linewidth Laser

Tunable and Programmable Fiber Ring Laser Based on Digital-Controlled Chirped Fiber Bragg Grating

A Single-Mode Polarization Maintaining Hollow Core Photonic Bandgap Fiber

High-Q, Low-Mode-volume Microsphere-Integrated Fabry–Perot Cavity for Optofluidic Lasing Applications

A Simple Approach to Fiber-Based Tunable Microcavity with High Coupling Efficiency

Study of tunable Fabry-Perot filter based on piezoelectric polymer film

Widely Tunable Laser Using Reflecting Fabry–Perot Filters with Lossy Half-Wave Trenches

Wide Wavelength Tuning in V-Coupled-Cavity Laser Integrated with a Fabry-Perot Filter

Tunable, Ultra-Narrow-Band Optical Filter Based on A Whispering Gallery Mode Hybrid-Microsphere

Half-Wave-Coupled Ring-FP Laser with 50-Channel 100-Ghz-spaced Wavelength Tuning

Silicon-Based On-Chip Fully Tunable Optical Fabry-Perot Filter Based on Multi-Mode Waveguide

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

Fiber-Integrated Reversibly Wavelength-Tunable Nanowire Laser Based on Nanocavity Mode Coupling.

GaAs/AlGaAs tunable laser using Fabry-Perot filters based on half-wave coupled lossy deep etched trenches

Fast and Wide-Band Tuning Single-Mode Microlaser Based on Fiber Fabry–Pérot Microcavities

Tunable narrow-linewidth fiber laser based on an optically controlled tunable filter

Tunable Liquid Crystal Fabry-Perot Filter for Dense Wavelength Division Multiplexing System

Single-mode and Wavelength Tunable Lasers Based on Deep-Submicron Slots Fabricated by Standard UV-lithography

Hybrid Wavelength Manipulation with Enhanced Ambient-Thermal Adaptability in an All-Polarization-Maintaining Mode-Locked Fiber Laser

Ultra-narrow bandwidth and large tuning range single-passband microwave photonic filter based on Brillouin fiber laser

Ultra-Narrow Bandwidth Microwave Photonic Filter Implemented by Single Longitudinal Mode Parity Time Symmetry Brillouin Fiber Laser