Abstract:In recent decades, geoelectrical methods have played a very important role in near-surface investigation. The most widely used of these methods is electrical resistivity tomography (ERT). Regardless of the forward and inversion algorithms used, the original data collected from a survey is the most important factor for quality of the resulted model. However, 3D electrical resistivity survey design continues to be based on data sets recorded using one or more of the standard electrode arrays. There is a recognized need for the 3D survey design to get better resolution using fewer data. Choosing suitable data from the comprehensive data set is a great approach. By reasonable selecting, better resolution can be obtained with fewer electrodes and measurements than conventional arrays. Previous research has demonstrated that the optimized survey design using the 'Compare R' method can give a nice performance.This paper adds target-oriented selection and modified the original 'Compare R' method. The survey design should be focused on specific target areas, which need a priori information about the subsurface properties. We select electrodes and configurations as the target set by the comprehensive set firstly which meets the requirements of the target area. The number of measurements and electrodes is much less than the comprehensive set and the model resolution matrix takes less time to calculate. At the next step for rank, we calculate the sensitivity matrix of the target set only once and then calculate the contribution degree of each measurement separately from it. The time of iterative calculation of the resolution matrix when measurements set changing is less than the original method.The traditional method of evaluating RMS is not appropriate for comparing the quality of collected data by different survey designs. SSIM (structural similarity index) gives more reliable measures of image similarity better than the RMS. The curves of SSIM values in three dimensions and the average SSIM are given as quantitative comparisons. Besides, the frequency of electrodes utilized given to guides on selecting the highest used electrodes. Finally, the curves of the average relative resolution S and the number of electrodes as the number of measurements increase are given, which proves the method works effectively.The results show the significance of using target-oriented optimized survey design, as it selects fewer electrodes and arrays than the original CR method. Also, it produces better resolution than conventional arrays and takes less calculation time. 3D SSIM, frequency of electrodes used, the relationship between average relative resolution, number of electrodes and number of measurements, these quantitative comparison methods can effectively evaluate the data collected in various survey designs.

Experimental research of LQC-I 3D resistivity survey system

Target-oriented Optimized Survey Design and Quantitative Comparison for 3D Electrical Resistivity Tomography

The Application of Capacitively-coupled Resistivity Method to Archaeological Exploration of Urban Site

Application of Three-Dimensional Electrical Resistivity Tomography in Urban Zones by Arbitrary Electrode Distribution Survey Design

The Study of 3-D Electrical Resistivity Tomography at an Archaeological Site

Capacitively Coupled Electrical Resistance Tomography System Based on Quartz Crystal Series Resonance

A novel electrical resistance tomography system based on C4D technique

Application on Ultra-Shallow 3D Seismic Exploration Technology

Application Study Of 3d Seismic Survey In Engineering Investigation

Three Dimensional Electrical Resistivity Structures of the Tarim Basin

Capacitively-Coupled Resistivity Methods And Its Application In Near-Surface Geophysical Prospecting

COMPLEX GEOLOGICAL STRUCTURE INDENTIFICATION AND PARA-METER ESTIMATION METHOD BASED ON 3D RESISTIVITY MEASURE-MENT

3D Inversion and 3D Visualization of 2D Survey Data Based on High Density Electrical Method: Take Guilester BarQin Mining Area As an Example

3D modeling and inversion of the electrical resistivity tomography using steel cased boreholes as long electrodes

Two-dimensional Inversion of CSAMT Data and Three-Dimensional Geological Mapping for Groundwater Exploration in Tongkeng Area, Hunan Province, China

Research and Application of 3D High Density Electrical Method

High-density Electrical Method Used in Cave Exploration of Building Foundation

Simulation and Application of a New Electromagnetic Resistivity Tool with Array Compensation Propagation While Drilling

3D inversion of audio-magnetotelluric data for mineral exploration: A case study of Layikeleke buried porphyry copper deposit, Xinjiang, China

Three-Dimensional Inversion of Controlled-Source Electromagnetic Data in Fanchang Region, Anhui Province

3D Inversion of Multifrequency Controlled-Source Electromagnetic Data and Its Application to Geothermal Exploration in the Tianzhen Region of the Northern Datong Basin, China