Abstract:Equal channel angular pressing (ECAP) is an efficient metal forming tool, generally used to improve the mechanical properties by refining the grain structure in metals and alloys. In the present work, both experimental and simulation approaches have been utilized to investigate the deformation behavior of EN AW 7075 alloy during ECAP. The formation and homogeneity of the Von-Mises stress and plastic strain of the samples during ECAP with different outer corner angles (OCAs) have been investigated by the finite element method (FEM). The results revealed that the effective strain was higher and uniform for 10°, 20°, and 30° OCAs die compared to other OCAs. Beyond 30°, the magnitude of strain was found lower with a less homogenous distribution of strain. A sharp plastic deformation zone (PDZ) was noticed for 10° and 20° OCAs, although broadened gradually over an OCA value of 20°. Moreover, lower and uniform Von-Mises stress was generated along the diameter of the sample for the OCA of 20° compared to other OCAs. A gradual reduction of plastic strain has been documented with the enhancement of OCAs along with the sample diameter. The sharpest damage, however, was noticed for the OCA of 90° due to the higher gap between the sample and both die surfaces. Interestingly, the most uniform severe plastic deformation and highest strain homogeneity in terms of inhomogeneity index and coefficient of variance were achieved for 20° and 30° OCAs. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) analysis illustrated the formation of ultra-fine grain structures containing very fine η ́ and η precipitates during the post-ECAP process. An improvement in the hardness, yield strength, and ultimate strength by 22%, 18%, and 14%, respectively, after ECAP has been recorded in comparison to the initial artificially aged condition. The improvements in mechanical properties were improvised primarily due to grain refinement combined with precipitate hardening.

Optimization of Strength and Ductility in Ultra-Fine 304 Stainless Steel after Equal-Channel Angular Processing

Achieving High Strength and High Ductility in 304 Stainless Steel Through Bi-Modal Microstructure Prepared by Post-Ecap Annealing

Microstructure and mechanical properties after annealing of equal-channel angular pressed interstitial-free steel

Corrosion Behavior Of Aisi 304 Austenitic Stainless Steel Fabricated By Equal-Channel Angular Pressing

A hybrid refining mechanism of microstructure of 304 stainless steel subjected to ECAP at 500°C

Thermal Stability of Ultrafine-Grained Low Carbon Steel Processed by Equal-Channel Angular Pressing

Microstructure and Properties of Ultrafine-Grained Aluminum-Based Alloy Processed by Equal Channel Angular Pressing

Improvement of Strength and Ductility of Mg-Zn-Ca-Mn Alloy by Equal Channel Angular Pressing

Realizing Strength–ductility Synergy in a Lean Duplex Stainless Steel Through Enhanced TRIP Effect Via Pulsed Electric Current Treatment

Investigating the Influence of Thermomechanical Equal Channel Angular Pressing (ECAP) Improved Die on AA-6061

FEA of Optimized Design for ECAP Die

Development of mechanical properties and microstructure for Al–Zn–Mg–Cu alloys through ECAP after optimizing the outer corner angles through FE modeling

Enhanced mechanical properties of ultrafine-lamella 304L stainless steel processed by multidirectional hot forging

Corrosion behaviour of nanocrystalline 304 stainless steel prepared by equal channel angular pressing

Microstructure Evolution and Mechanical Properties of a Ti–35Nb–3Zr–2Ta Biomedical Alloy Processed by Equal Channel Angular Pressing (ECAP)

Mechanical responses, texture and microstructural evolution of high purity aluminum deformed by equal channel angular pressing

Grain Refinement and Strengthening of an Aluminum Alloy Subjected to Severe Plastic Deformation through Equal-Channel Angular Pressing

Intermediate Annealing of Pure Copper During Cyclic Equal Channel Angular Pressing

Microstructure Evolution and Mechanical Properties of Fcc Metallic Materials Subjected to Equal Channel Angular Pressing

Impact of Equal Channel Angular Pressing on Mechanical Behavior and Corrosion Resistance of Hot-Rolled Ti-2Fe-0.1B Alloy

Mechanical Properties and Microstructure Evolution of Ultra-High Strength Al-Zn-Mg-Cu Alloy Processed by Room Temperature ECAP with Post Aging