Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Texture Analysis of Commercial Pure (grade 3) Ti after Two-Step Severe Plastic Deformation

Mechanism of Crystallographic Orientation and Texture Evolution of Ti60 Alloy during Plane Strain Compression

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Textures of Rectangular Extrusions and Their Effects on the Mechanical Properties of Thermo-Mechanically Treated, Lamellar Microstructure, Ti–47Al–2Cr–2Nb–0.15B

Effect of the Texture of the Ultrafine-Grained Ti-6Al-4V Titanium Alloy on Impact Toughness

The Role of Deformation and Microstructure Evolution on Texture Formation of a TA15 Alloy Subjected to Plane Strain Compression

Tension-Compression Asymmetry in Ultrafine-grained Commercially Pure Ti Processed by ECAP

Correlation between plastic deformation mechanism and texture evolution of a near β-Ti alloy deformed in β region

Analysis of the texture evolution during multipass tube spinning of a TA15 alloy using the crystal plasticity finite element model

Texture Evolution and Mechanical Behavior of Commercially Pure Ti Processed Via Pulsed Electric Current Treatment

Effect of Texture on the Ductile–Brittle Transition Range and Fracture Mechanisms of the Ultrafine-Grained Two-Phase Ti-6Al-4V Titanium Alloy

Plastic Deformation Mechanism and Slip Transmission Behavior of Commercially Pure Ti during In Situ Tensile Deformation

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Tailoring texture in a near-α titanium alloy: Insights from strain paths and cooling rate influences

The Action Mechanism of Rolling Texture on the Anisotropic Behavior of a Pure Titanium Plate

Texture evolution and slip mode of a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr dual-phase alloy during cold rolling based on multiscale crystal plasticity finite element model

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

Probing the texture transition sequence of near β titanium matrix composites by observing the uneven hot deformation microstructure

Microstructural Development, Deformation Behavior, and Texture Evolution Investigation during Hot Compression of a Dynamically Recrystallized Ti-5Cu Alloy in the Dual (α + β) Phase Region

Differences in Texture Evolution from Low-Entropy to High-Entropy Face-Centered Cubic Alloys During Tension Test

In-situ synchrotron high energy X-ray diffraction study on the deformation mechanisms of D0 19 -α 2 phase during high-temperature compression in a TiAl alloy