Abstract:Hydrogen is a potential green alternative to conventional energy carriers such as oil and coal. Compared with the storage of hydrogen in gaseous or liquid phases, the chemical storage of hydrogen in solid complex hydrides is safer and more effective. In this study, the complex hydride composite 2LiBH4–Li 3 AlH 6 with different amounts of TiF 3 was prepared by simple ball-milling and its hydrogen storage properties were investigated. Temperature programmed desorption and differential scanning calorimetry were used to characterize the de/rehydrogenation performance, and X-ray diffraction and scanning electron microscopy (SEM) were used to explore the phase structure and surface topography of the materials. The dehydrogenation temperature decreased by 48°C in 2LiBH4–Li 3 AlH 6 with 15 wt% TiF 3 composites compared to the composite without additives while the reaction kinetics was accelerated by 20%. In addition, the influence of hydrogen back pressure on the 2LiBH4–Li 3 AlH 6 with 5 wt% TiF 3 composite was also investigated. The results show that hydrogen back pressure between 2.5 and 3.5 bar can improve the reversible performance of the composite to some extent. With a back pressure of 3.5 bar, the second dehydrogenation capacity increased to 4.6 wt% from the 3.3 wt% in the 2LiBH 4 –Li 3 AlH 6 composite without hydrogen back pressure. However, the dehydrogenation kinetics was hindered. About 150 h, which is 100 times the time required without back pressure, was needed to release 8.7 wt% of hydrogen at 3.5 bar hydrogen back pressure. The SEM results show that aluminum was aggregated after the second cycle of dehydrogenation at the hydrogen back pressure of 3 bar, resulting in the partial reversibility of the 5 wt% TiF 3 -added 2LiBH4–Li3AlH 6 composite.

Low-Temperature Hydrogen Desorption from Libh4-Tif4 Composite

A new strategy to remarkably improve the low-temperature reversible hydrogen desorption performances of LiBH4 by compositing with fluorographene

Synergistic Catalysis of Fe2o3 and Tif3 Additives on the Libh4-Mgh2 Composite

In Situ Formation of TiB2 and TiH2 Catalyzed Li/Mg Based Dual-Cation Borohydride with a Low Onset Dehydrogenation Temperature below 100 °C

Destabilized dehydrogenation reaction of LiBH4 by AlF 3

Improved dehydrogenation/rehydrogenation performance of LiBH 4 by doping mesoporous Fe 2 O 3 or/and TiF 3

LiAlH4 As a “microlighter” on the Fluorographite Surface Triggering the Dehydrogenation of Mg(BH4)2: Toward More Than 7 Wt % Hydrogen Release below 70 °C

Hydrogen storage properties of Ti/TiF3-doping LiAlH4/LiNH2 composites

Hydrogen Storage Properties of LiBH4–Li3AlH6 Composites

Hydrogen desorption from LiBH4 destabilized by chlorides of transition metal Fe, Co, and Ni

In-situ Introduction of Highly Active TiO for Enhancing Hydrogen Storage Performance of LiBH4

Excellent Low-Temperature Dehydrogenation Performance and Reversibility of 0.55Libh4-0.45Mg(bh4)2 Composite Catalyzed by Few-Layer Ti2C

Improved hydrogen desorption properties of LiBH4 by AlH3 addition

Enhanced Hydrogen Storage Properties of LiBH4 Modified by NbF5

Low-Temperature Dehydrogenation of Libh4 Through Destabilization with Tio2

Significantly Improved Dehydrogenation of Libh4 Destabilized by Tif3

Hydrogen Desorption Kinetics of the Destabilized LiBH 4 AlH 3 Composites

Dehydrogenation Properties and Mechanism of LiBH4/Li3AlH6 Composite

Effect of Different Amounts of TiF3 on the Reversible Hydrogen Storage Properties of 2LiBH4–Li3AlH6 Composite

Reversible Hydrogen Storage in Titanium-Catalyzed LiAlH4–LiBH4 System

Dehydrogenation Performances of Different Al Source Composite Systems of 2libh4 + M (M = Al, LiAlH4, Li3AlH6).