Abstract:Laser cladding is a new technology for fabricating coatings with good properties, such as wear resistance, lubrication, and corrosion resistance. Usually, parts of 45 steel are used as a shaft under conditions of high-speed rotation or friction and wear, and they have a short service life and sometimes cause accidents. In order to avoid serious accidents, a cladding coating made from a Ni-based alloy with ceramic particles was fabricated via laser technology on a substrate of 45 steel in this research. The microstructure and properties were investigated via SEM, EDS, XRD, and a wear and friction tester. The results show that there was an obvious boundary between the cladding coating and the substrate. The main phases were γ(Fe, Ni), WC, TiC, Cr2Ti, and Cr23C6. In the middle of cladding coating, the microstructure was composed of dendrite and cellular crystals, while the microstructure was composed of equiaxial crystals in the bonding region. Inside the cellular crystal, the main phase was γ~(Fe, Ni), which occasionally also showed the appearance of some white particles inside the cellular crystal. Compared with the cellular crystal, the boundary had less of the Fe and Ni elements and more of the Cr and W elements. The amount of C element around the dendrite crystal was more than that around the boundary of cellular crystal due to the long formation time of dendrite. The white particles around the boundary were carbides, such as WC and Cr23C6 phases. Meanwhile, the segregation of the Si element also appeared around the boundaries of the crystal. The maximum microhardness was 772.4 HV0.5, which was about 3.9 times as much as the substrate's microhardness. The friction coefficients of the 45 steel substrate and Ni-based alloy coating were usually around 0.3 and 0.1, respectively. The Ni-based coating had a smaller coefficient and more stable fluctuations. The wear volume of the cladding coating (0.16 mm3) was less than that of the substrate (1.1 mm3), which was about 14.5% of the wear volume of 45 steel substrate. The main reason was the existence of reinforced phases, such as γ~(Fe, Ni), Cr23C6, and Cr2Ti. The added small WC and TiC particles also enhanced the wear resistance further. The main wear mechanism of the cladding coating was changed to be adhesive wear due to the ceramic particles, which was helpful in improving the service life of 45 steel.

Effect of niobium on the microstructure and wear resistance of nickel-based alloy coating by laser cladding

Effect of process parameters and niobium carbide addition on microstructure and wear resistance of laser cladding nickel‐based alloy coatings

Effect of Cobalt on Microstructure and Wear Resistance of Ni-Based Alloy Coating Fabricated by Laser Cladding

Effects of Nb content on the microstructure and properties of CoCrFeMnNiNb x high-entropy alloy coatings by laser cladding

Effect of niobium content on microstructure and wear and corrosion resistance of laser-clad FeCo0.5CrNi1.5B0.5Nbx coatings on ductile iron

Effect of Nb content on microstructure and corrosion resistance of Inconel 625 coating formed by laser cladding

Effect of the Nb content on the microstructure evolution and properties of the CrFeCoNiNb x layers prepared by laser cladding

Microstructure and properties of laser clad Fe-based amorphous alloy coatings containing Nb powder

Effect of graphene and niobium carbide on microstructure and mechanical properties of Ni60 composite coatings prepared by laser cladding

Characterization and tribological evaluation of NiCrMoNb and NiCrBSiC laser cladding on near-α titanium alloy

Effect of Nb Content on the Tribological Properties of Laser-Cladded Ti-Al-C MAX Phase Composite Coatings

Effect of NbC in-situ synthesis on the microstructure and properties of pre-placed WCoB-TiC coating by laser cladding

Effect of Nb Content on Phase Transformation and Comprehensive Properties of TiNb Alloy Coating

Effects of the Proportions of Carbon on the Microstructure and Properties of NbC-Reinforced Ni-WC Composite Coatings by Laser Cladding In-situ Synthesis

Effect of La2O3 on the microstructure and wear resistance of laser clad nickel-based alloy coatings

Mechanical and Tribological Properties of Fe- and Ni-based Coating Material under Laser Cladding Process

Effect of Ceramic Particles on Ni-Based Alloy Coating Fabricated via Laser Technology

Influence of Nb on the microstructure of laser clad composite coating reinforced by in-situ particles

Microstructure and Corrosion Behavior of Ti-Nb Coatings on NiTi Substrate Fabricated by Laser Cladding

Properties of Ti–Zr–Nb–Cu–Ni multi-principal-component alloy coatings prepared by laser cladding on a Ti–6Al–4V surface

Effect of Laser Cladding Layers on Microstructure and Mechanical Properties of NiCoCrAlY Bond Coat