Abstract:This study investigated the failure behavior and mechanism of conductive and corrosion-resistant film on magnesium alloy under "double 85" test conditions. The surface morphology, microstructure, and composition of ITO composite conversion film (ITO film) at different damp-heat test times were analyzed using X-ray photoelectron spectroscopy, scanning electron microscopy and energy-dispersive X-ray spectroscopy, and the corrosion resistance was investigated using an electrochemical workstation in contact with a 3.5 wt.% NaCl solution. The electrical contact resistance (ECR) was measured using the four-wire Kelvin detection technique, and the bandgap was determined using an ultraviolet diffuse reflectance spectrometer. The results demonstrated that the ECR of the ITO film increased from 10 −1 Ω in −2 to 10 6 Ω in −2 , and the bandgap increased from 2.363 to 2.777 eV after the damp-heat test. In addition, the impedance arc radius of the film decreased to approximately one-fifth of its original value, and the impedance modulus value decreased to less than 10 4 . These findings indicated that exposure to a damp-heat environment resulted in an increase in the electrochemically active points within the film participating in the electrochemical reactions and expansion of the electrochemical reaction area. This exacerbated the corrosion of the magnesium substrate because it resulted in the destruction of the film, leading to an increase in the number of pores and defects, which heightened the exposure of the substrate to corrosive media. Furthermore, Cl − ions could easily penetrate through cracks in the film, which promoted charge transfer processes and accelerated the electrochemical corrosion reactions. In summary, these factors collectively resulted in the failure of the film's conductivity and corrosion resistance.

Corrosion performance study of anodic film formed by oxidizing magnesium alloy in environmentally friendly electrolyte

Study on microstructure and corrosion resistance of anodic film of magnesium alloy

Study on the Environmentally Friendly Anodizing of AZ91D Magnesium Alloy

Corrosion Properties of AZ31 Magnesium Alloy and Protective Effects of Chemical Conversion Layers and Anodized Coatings

Anodization of AZ91 Magnesium Alloy in Alkaline Solution Containing Silicate and Corrosion Properties of Anodized Films

Influence of Anodic Oxidation on the Organizational Structure and Corrosion Resistance of Oxide Film on AZ31B Magnesium Alloy

Effect of Electrical Parameters on the Microstructure and Corrosion Resistance of Anodized Film of Mg-1Zn-1Gd Alloy Based on Orthogonal Experiment Method

Plasma Electrolytic Oxidation of AZ91D Magnesium Alloy with Different Additives and Its Corrosion Behavior

Study on the Anodic Film Formation Process of AZ91D Magnesium Alloy

Corrosion behavior of anodized AZ91D magnesium alloy in NaCl aqueous solution

Anodizing of AZ91D Magnesium Alloy Using Environmental Friendly Alkaline Borate-Biphthalate Electrolyte

Structure, Composition and Corrosion Resistance of Mg Alloy Anodized Film

Magnesium Alloy Corrosion under Thin Electrolyte Layer Using Electrochemical Impedance Spectroscopy and Polarization Curve

Enhanced Corrosion Resistance of AZ91D Magnesium Alloy by Electric Field – Assisted Anodizing

Biodegradation of Az31 and We43 Magnesium Alloys in Simulated Body Fluid

Effects of Electric Parameters on Corrosion Resistance of Anodic Coatings Formed on Magnesium Alloys

Electrochemical Behavior of ZE41 Magnesium Alloy under Simulated Atmospheric Corrosion

Corrosion resistance enhanced by an atomic layer deposited Al2O3 /micro-arc oxidation coating on magnesium alloy AZ31

The Anodization of Zk60 Magnesium Alloy in Alkaline Solution Containing Silicate and the Corrosion Properties of the Anodized Films

Tuning Corrosion Properties of the Bio-Inspired AZ-Series Mg Alloys Using Electrochemical Surface Treatment under Varying Experimental Regimes

Study on failure behavior of conductive and corrosion-resistant conversion film on magnesium alloy in damp-heat environment